Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. If o = 4 ksi in the direction shown, determine the magnitude of the maximum in-plane shear stress at the point. O 11.5 ksi O 16.1 ksi O 13.0 ksi 10.5 ksi O 17.0 ksi 14 ksi 12 ksi

Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. If o = 4 ksi in the direction shown, determine the magnitude of the maximum in-plane shear stress at the point. O 11.5 ksi O 16.1 ksi O 13.0 ksi 10.5 ksi O 17.0 ksi 14 ksi 12 ksi

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter8: Vertical Stress Increase In Soil

Section: Chapter Questions

Problem 8.6P: Two line loads q1 and q2 of infinite lengths are acting on top of an elastic medium, as shown in...

See similar textbooks

Similar questions

The state of stress at a point is the result of two loadings as shown in figure. When acting alone, the first loading produces the 3 MPa pure shear with respect of xy-axis. The second loading alone results in the 4 MPa pure shear with respect to the x'y-axis. The angle between the two sets of axis is 30° as shown. If the two loadings act simultaneously then resultant (absolute) shear stress at that point with respect to x-y axis is MPa (in integer). 3 MPa st 1 loading 2 loading 4 MPa α = 30° x'
The stresses acting on element A on the web of a train rail (see part (a) of the figure) are found to be 50 MPa tension in the horizontal direction and 140 MPa compression in the vertical direction (see part (b) of the figure). 140 MPa B 50 MPa A A Side View Cross 57 MPa Section (a) (b) Also, shear stresses of magnitude 57 MPa act in the directions shown. Determine the stresses (in MPa) acting on an element oriented at a counterclockwise angle of 52° from the horizontal. (Use the sign convention for stresses acting on inclined sections. Round your answer for o,1 to at least one decimal place.) Ov1 = MPa MPa Oyi MPа Tx1y1 Show these stresses on a sketch of an element oriented at this angle. (Submit a file with a maximum size of 1 MB. Your submission will be graded by your instructor after the due date based on its accuracy. Your grade may change.) Choose File No file chosen
es A state of stress at a point is the result of two separate actions; one produces the pure shear of 35 MPa shown in figure A and the other produces the pure shear of 30 MPa shown in figure B. 35 MPa -19.86 degrees Y -17.04 degrees -X Figure A Which of the following most nearly gives the principal planes for the combined state of stress? Select the correct response: 35 MPa 30° Figure B 30 MPa 30 MPa 4
An element in plane stress on the fuselage ofan airplane (figure part a) is subjected to compressivestresses with a magnitude of 42 MPa in the horizontaldirection and tensile stresses with a magnitude of9.5 MPa in the vertical direction (see figure part b).Also, shear stresses with a magnitude of 15.5 MPa actin the directions shown.Determine the stresses acting on an element orientedat a clockwise angle of 40° from the horizontal.Show these stresses on a sketch of an element orientedat this angle.
Q.2) A rigid bar ACD is supported by two circular steel (E= 30x10° psi) rods AB & DE and a pin support at C. Bar ACD was horizontal prior to the application of load P. The tensile strain measured in rod AB after the application of the load is ɛ1= 0.003. Determine the rotation 0 of the bar ACD and the normal strain in rod DE. Also calculate the value of load P for these deformations. The diameters of rod AB and DE are 1.5 in. and 2 in, respectively. P - 4 ft 4 ft- 6 ft A Rigid (2) 6 ft 8 ft (1) E В
Q36 onlys Ratio of stress in part A and B
A simply supported beam is loaded by the couple M=2000 N-m as shown. The beam has a channel-type cross section as illustrated. 3 cm 30 cm 3 cm 3 m -2m1 10.5 cm BI 12 cm M. Determine the maximum tensile stress in the beam. O 1.60 MPa 3.73 MPa )2.49 MPa O1.07 MPa Determine the maximum compressive stress in the beam. 3.73 MPa O 1.07 MPa 2.49 MPa O 1.60 MPa Determine the maximum shear stress in the beam. O 00588 MPa 0.0490 MPa 0.0653 MPa O 0.0667 MPa
6. Due to a loading, the plate is deformed into the dashed shape shown in the figure below. Determine (a) the average normal strain along the side AB, and (b) the average shear strain in the plate at A relative to the x and y axes. 0.13 in В 0.09 in 10 in A 12 in C
Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. If o = 25 MPa in the direction shown, determine the principal stresses at the point. 28 MPa 16 MPa O 39.2 MPa and -30.2 MPa O 31.6 MPa and -35.8 MPa 54.1 MPa and -41.3 MPa 35.8 MPa and -27.4 MPa O 27.7 MPa and -39.0 MPa Save for Later eTextbook and Media Attempts: 1 of 3 used Submit Answer
A thin-walled long cylindrical tank of inside radius r is subjected simultaneously to internal gas pressure p and axial compressive force F at its ends. In order to produce 'pure shear state of stress in the wall of the cylinder, F should be equal to лрr² 2πpr² 3πpr² 4πpr²
2. Determine the shearing stress in each of the four walls of a portion of a structural aluminum tubing when it is subjected to a torque of 3 kN-m assuming a uniform wall thickness of 4mm. A ( 51 ) mm В 100 mm 100 mm C D ( 51 ) mm
2.25. A system consists of two rigid end-plates, tied together by three horizontal bars as shown in Fig. 2-42. Through a fabrication error, the central bar, ②2, is 0.0005L too short. All bars are of identical cross section and of steel having E = 210 GPa. Find the stress in each bar after the system has mechanically been pulled together so that the gap A is closed. Ans σ-35 MPa σ = 70 MPa Fig. 2-42