Consider a steam power plant that operates on the ideal reheat Rankine cycle as shown in Fig. Q5. The plant maintains the boiler at 7000 kPa, the reheat section at 800 kPa, and the condenser at 10 kPa. The mixture quality at the exit of both turbines is 93 percent. Determine the temperature at the inlet of each turbine and the cycle's thermal efficiency. Rcheater Boiler High-P turbine Pump Low-P turbine Condenser G

Consider a steam power plant that operates on the ideal reheat Rankine cycle as shown in Fig. Q5. The plant maintains the boiler at 7000 kPa, the reheat section at 800 kPa, and the condenser at 10 kPa. The mixture quality at the exit of both turbines is 93 percent. Determine the temperature at the inlet of each turbine and the cycle's thermal efficiency. Rcheater Boiler High-P turbine Pump Low-P turbine Condenser G

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A simple power plant utilizing the Rankine Cycle operates with an inlet boiler pressureof 5 MPa and an inlet condenser pressure of 300 kPa. Because of frictional effects, thepressure of the water drops 0.3 MPa in the boiler and 3 kPa in the condenser. Thetemperature of the steam as it enters the turbine is 700 °C. The adiabatic efficiency ofthe pump and of the turbine are 83 percent and 88 percent, respectively. The pumpand the turbine are adiabatic, and the water enters the pump as saturated liquid. It canbe assumed that heat transfer to the water in the boiler is from a reservoir at 1500 K,and the environment is at 25 °C.Determine the thermal efficiency of the cycle and compare it with the thermal efficiencyof (a) a Carnot cycle, and (b) the ideal Rankine Cycle. Specify the amount of entropygenerated in each step of the real cycle
A 120 MW gas turbine power plant running on Ideal Brayton cycle has the followinginitial conditions; air at 22°C & 95 kPa. The compression ratio is 7 and the temperature atthe turbine entrance is 910°C. Determine the following:a. Thermal Efficiencyb. Mass flow rate, kg/min
A power plant operating on an ideal Rankine cycle has steam entering theturbine at 500°C and 2 MPa. If the steam enters the pump at 10 kPa, calculate the thermal efficiency with pump work included, the thermal efficiency neglecting pump work, and the percentage error in efficiency neglectingpump work.
A basic Rankine steam power plant uses an adiabatic turbine that operates with inlet steam at 6.80 MPa and 550.0 ∘C.The exhaust steam enters the condenser at 50.0 ∘C with a quality of 0.960. Saturated liquid water leaves the isobaric condenser and is pumped to the boiler. Mass flow through the cycle is 2.900 kg/s. Neglecting pump work and kinetic and potential energy changes, determine: the work interaction term of the turbine: the thermal efficiency of the cycle, ?th:
A basic Rankine steam power plant uses an adiabatic turbine that operates with inlet steam at 6.80 MPa and 550.0 ∘C. The exhaust steam enters the condenser at 50.0 ∘C with a quality of 0.960. Saturated liquid water leaves the isobaric condenser and is pumped to the boiler. Mass flow through the cycle is 2.900 kg/s. Neglecting pump work and kinetic and potential energy changes, determine: the work interaction term of the turbine: the thermal efficiency of the cycle, ?th: the second law efficiency of the turbine, ?2nd:
In a simple Rankine cycle, the working fluid is water, operating at pressures between 7.5 kPa and 1750 kPa. The water vapor is in the form of saturated steam at the turbine inlet. Turbine expansion andCalculate the thermal efficiency of the cycle, assuming that the compression processes in the pump are reversible adiabatic.
Air enters the compressor of a regenerative gas-turbine engine at 100 kPaand 300 K and is compressed to 800 kPa. The regenerator has aneffectiveness of 65 percent, and the air enters the turbine at 1200 K. For acompressor efficiency of 75 percent and a turbine efficiency of 86 percent,determine(a) The heat transfer in the regenerator.(b) The back work ratio.(c) The cycle thermal efficiency
A Rankine Cycle operates between high and low temperature reservoirs at 1500oC and 25oC respectively. What is the maximum theoretical efficiency of this cycle?
There is a simple real rankine cycle, in which the steam enters the turbine with a pressure of 5MPa and a temperature of 500°C. The working pressure of the condenser is 20kPa. The mass flow of steam 35.4 kg/s. The Isoentropic efficiency of the turbine is 88% And the isoentropic efficiencyof the pump is 84%. Determine: a) The thermal efficiency of the cycle b) The net power produced by this cycle
A power plant is to be operated on an ideal Rankine cycle with the superheatedsteam exiting the boiler at 4 MPa and 500°C. Calculate the thermal efficiencyand the quality at the turbine outlet if the condenser pressure is (a) 20 kPa,(b) 10 kPa, and (c) 8 kPa.
A 283-MW steam power plant operates on the Rankine cycle but with turbine and pump efficiencies of 90%. The steam enters the turbine at 10,000 kPa and 550°C. It discharges to the condenser at 50 kPa. Determine the thermal efficiency in percent.
A four-cylinder compression-ignition engine with a compression ratio of 18 haspistons with a bore of 9 cm and a stroke of 10 cm. The air pressure at the beginning ofcompression is 98 kPaa, and the temperature is 37 oC. The engine may be modeled bythe air-standard Diesel cycle. The maximum cycle temperature is 1700 oK. If the engineproduces 75 kW of power, determine a) the heat supplied per cylinder; b) the thermalefficiency; and c) the rpm required.