Consider pin A, which is used in a single shear connection. Use the ultimate shear strength, the factor of safety, and the force at A to calculate the minimum required diameter for pin A.dpinA= ? (unit mm) Rigid beam AB is subjected to a distributed load that increases linearly from zero to a maximum intensity of wB = 24.5 kN/m. Beam ABis supported by a single-shear pin connection at joint A and by a double-shear connection to member (1) at joint B. Member (1) isconnected to the support at C with a double-shear pin connection. Use dimensions of a = 2.3 m, b 0.9 m, and c = 1 m.(a) The yield strength of member (1) is 309 MPa. A factor of safety of 1.7 with respect to the yield strength is required for the normalstress of member (1). Determine the minimum cross-sectional area required for member (1).(b) The ultimate shear strength of the material used for pins A, B, and Cis 210 MPa. A factor of safety of 2.8 with respect to theultimate shear strength is required for the pins, and all three pins are to have the same diameter. Determine the minimum pindiameter that may be used.WB(1)a

Answered: Image /qna-images/answer/31dcb88a-17d0-4621-891b-ce1a2a5988bf.jpg

Consider pin A, which is used in a single shear connection. Use the ultimate shear strength, the factor of safety, and the force at A to calculate the minimum required diameter for pin A. dpinA= ? (unit mm)

Consider pin A, which is used in a single shear connection. Use the ultimate shear strength, the factor of safety, and the force at A to calculate the minimum required diameter for pin A. dpinA= ? (unit mm)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Given: Bolt diameter = 20 mm ø Bolt hole diameter = 23 mm ø Plate thickness, t= 25 mm Bolt shear…

A: We will use basic formulas.

Q: Determine the length (m) of the shortest 2-mm-diameter bronze wire which can be twisted through two…

A: We know torsion relationτr=GφLτ=shearing stress =70Mpar=d2=1mmG=35×103Mpaφ= 2 turns =22π=4π rad

Q: 4) Shear and Moment. Two identical 20-mm thick plates are bolted to the top and bottom flange to…

A: Draw cross-section:

Q: PROBLEM 1. A flanged bolt coupling is used to connect two solid shafts. Each shaft has a diameter of…

A: NOTE : According to guidelines, only problem 1 is solved. Please post problem 2 separately. Given,…

Q: The pressure tank shown is fabricated from spirally-wrapped metal plates that are welded at the…

Q: 3. Determine the length of the 2-mm diameter bronze wire which can be twisted through two complete…

Q: A connection using 3 bolts with the eccentricity is shown in Figure Q3. Determine: (a) Average shear…

Q: A screw is rotated as shown to provide tension on a cable that passess over a frictionless pulley…

A: The given figure is shown below:

Q: Problem 2: A shaft is to be fitted with a flanged coupling having 6 bolts on a circle of diameter…

Q: 1. Determine the maximum torque Tin kN-m without exceeding a shear stress of 70 MPa in steel and 50…

A: Given, Gst = 83 GPa or 83000 MPa Gbr = 35 GPa or 35000 MPa

Q: r, In the given system the pin at A has a diameter of 8 mm and the pins at B and D have diameters of…

A: Given data Length Diameter FOS Normal stress Shear stress

Q: Calculate each of the following under 20 kN load on a structure given below where all pins have a…

Q: A flanged-bolt connection is arranged as shown. Each bolt has a diameter of d = 25 mm. If P 85 kN,…

Q: The following steel rod is subjected to the loadings as shown below. If the diameter of the rod is…

A: Given data in question Point loads acting on various sections Length of members Diameter 8 mm…

Q: Prob. 6 * The pipe wrench is parallel to the z-axis, and is subjected to a 40lbf force in the -y…

Q: P 100 mm 10 mm 10 mm P

A: As per bartleby guidelines the given data closely related to the IS code provisions also the term…

Q: Pins B and C experience the same force, and are both used in a double shear connection. Consider pin…

Q: A force P = 85 kN is applied at the plate-bolt connection shown. Determine the required diameter in…

A: Appreciate if there is detailed work with explanation and finds you helpful for ease of…

Q: Two A36 16mm Thick Steel Plates Are Connected By Four Rivets With Fv=152 MPa As Shown. Given:…

Q: Determine the resultant load on the most stressed bolt in the eccentrically loaded connections…

A: first find the moment M=Pewhere = p = acting loade=eccentricity of loadM=100×6M=600k-in now find…

Q: 1) what is the block shear in plate moment connection in steel members. How the allowable moment…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: 9. The gusset shown is riveted to the column flange by 7-20mm diameter rivet single shear. Determine…

A: The values and diagram given in the question are as follows: diameter of rivet(ϕ)=20 mm Number of…

Q: Situation 8: For the connection shown in the figure. Pu = 80 KN, x1 = 200, x2 = 100, y1 = 50, y2 =…

A: Given data in question Load Dimensions To find out Maximum force in a bolt due to load alone

Q: Determine the resultant load on the most stressed bolt in the eccentrically loaded connections…

A: Consider the free body diagram;

Q: The yoke-and-rod connection shown is subjected to a tensile force of 5 kN. Determine the average…

Q: Situation 8: For the connection shown in the figure. Pu = 80 KN, x1 = 200, x2 = 100, y1= 50, y2 = y3…

Q: 1.7-1 An angle bracket having thickness 19 mm is attached to the flange of a column by two 16 mm…

A: t=19mm Diameter of bolt (d) = 16mm Pressure (p) =1.9MPa Length (L) =200mm Width(b) =75mm

Q: ouble shear. : Tall of pin A = 100 MPa Sall on the rod BC = 20 MPa diameter of pin A, Øpin A = 10 mm…

A: According to given data Find the largest load P, that can be carried safely by the system below.…

Q: The angle bracket shown, 75 mm x 75 mm x 15 mm thick, is 200 mm long. It is connected to the 16 mm…

Q: (For Nos. 1-2) Determine if the structure is unstable, determinate or indeterminate. In case of…

Q: A bolted connection shown in figure A uses the friction type connection with 22mm diameter A 325…

Q: For the rivet connection shown in figure 2-4, the allowable shearing stress in the 25mm rivets is…

Q: 12 in. 9 in. B 40 lb The pipe wrench is parallel to the z-axis, and is subjected to a 40lbf force in…

Q: L1 L2 C W Fig. A Fig. B

Q: 1. For the connection shown in the figure below, determine the shearing stress in the most heavily…

A: In designing practice it isn't unexpected needed that two sheets or plates are combined and convey…

Q: polyethylene having an ultimate tensile strength of 3200 psi and an ultimate bearing strength of…

A: Given:- b=0.625in t=0.15in ultimate tensile strength=3200psi To find:- allowable normal stress…

Q: Double shear happens when you have O a. yoke connection O b. to use a rivet and connect two flat…

A: Shear stress which acts parallel or tangential to the surface at a joint, that is known as double…

Q: 2. A 101.6 mm diameter shafting SAE 1040 grade, cold rolled, having a yield point of 60 ksi and 2/3…

A: The diameter of the shaft is d=101.6 mm or d=4 in. The yield point of the shaft is τ=60 ksi. The…

Q: 12 in. 9 in. 40 lb ») The pipe wrench is parallel to the z-axis, and is subjected to a 40lbf force…

Q: W = L2 = %3D 2.4 1.2 KN m L3=1.2 L1 = L3 1.2 1.2 Typical connection at all joints. m Im Li=1.2…

Q: A box beam is constructed of four wood boards as shown in the figure part (a). The webs are h = 8…

A: F=280lb V=1200lb t=1in b=6in h1=8in

Q: H.W.4 Two 6-in.-wide wooden boards are to be joined by splice plates that will be fully glued onto…

A: The smallest allowance length L Solution 6 wide cupboard in Double Shear…

Q: Situation 10: For the connection shown in the figure. Pu = 100 KN, x1 = 200, x2 = 200, y1 = 50, y2 =…

Q: If the required clamping force at the board A is to be 2 kN, determine the torque M that must be…

A: Given Data: The clamping force required is F=2 kN. The mean radius of the square-threaded screw is…

Q: a. If the control rod AB is made of a steel having an ultimate normal stress of 600MPA, determine…

Q: A flanged bolt coupling consist of six 10 mm. diameter steel bolts on a bolt circle 300 mm. in…

Q: A wooden box beam is fabricated from four boards, which are fastened together with screws. Each…

A: Determine the maximum permissible spacing intervals for the screws.

Q: • Compute the available block shear strength of the connection based on the KN. (Diameter of hole is…

Q: A flanged-bolt coupling consisting of six % inch diameter steel bolts evenly spaced around a bolt…

Question

Rigid beam AB is subjected to a distributed load that increases linearly from zero to a maximum intensity of wB = 24.5 kN/m. Beam AB
is supported by a single-shear pin connection at joint A and by a double-shear connection to member (1) at joint B. Member (1) is
connected to the support at C with a double-shear pin connection. Use dimensions of a = 2.3 m, b 0.9 m, and c = 1 m.
(a) The yield strength of member (1) is 309 MPa. A factor of safety of 1.7 with respect to the yield strength is required for the normal
stress of member (1). Determine the minimum cross-sectional area required for member (1).
(b) The ultimate shear strength of the material used for pins A, B, and Cis 210 MPa. A factor of safety of 2.8 with respect to the
ultimate shear strength is required for the pins, and all three pins are to have the same diameter. Determine the minimum pin
diameter that may be used.
WB
(1)
a

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The electric power transmission tower supports two wires that apply 18 kN verticalforces, and the 36 kN horizontal force crudely models wind loading during astorm. Assume that the supports in A and B are hinge support and roller support,respectively. Solve for support reactions.
An L= 29-ft-long soldier beam is used as a key component of an earth retention system at an excavation site. The soldier beam is subjected to a soil loading that is linearly distributed from WA = 600 lb/ft to Wc= 220 lb/ft, as shown. The soldier beam can be idealized as a cantilever with a fixed support at A. Added support is supplied by a tieback anchor at B, which exerts a force of P = 5100 Ib on the soldier beam at a = 22 ft. Determine the horizontal deflection of the soldier beam at point C. Assume El = 6.5 × 10^8 Ib-in.^2. Deflection is positive to the left.
A simply supported beam is 3m long. It carries a uniformly distributed load of 6 kN/m throughout its span and a concentrated load of 15 kN at a point 2 m from the left support.1. what most nearly gives the maximum shear developed in the beam?2. what most nearly gives the maximum moment developed in the beam?3. Assuming that the beam has a rectangular shape whose width and depth are 150 mm and 250 mm, respectively, which of the following most nearly gives the maximum flexural stress developed in the beam?
Determine the max positive shear that can be developed at point C in the beam due to concentrated moving load of 4000lb and a uniform moving load of 2000lb/ft
The roof deck of the single story building is subjected to a dead load plus live load of 45 kN/m2. If the purlins are spaced 1.5 m and the bents are spaced 6 m apart, determine the distributed loading in kN/m that acts along the purlin DI.
Determine the shear force V in the beam at the point located 2.50 m to the left of point C. The ground reactions and shear-force diagram are shown. -30.6 kN -48.2 kN -57.2 kN -38.2 kN -40.9 kN
A propped beam has a span of 7.2 meters is simply supported at C. It carries a concentrated load of 60 kN, 3 meters from C. EI = 3000 kN.m2. reaction at C, in kN angle of rotation at C deflection at B, in mm
A 6.5m long cantilever beam 300mm x 600mm carries a uniformly distributed dead load(beam weight included) of 5kN/m throughout the length and a concentrated live load of 19KN at the free end. To prevent excessive deflection of the beam it is pretensioned with 12mm diameter strands causing a final prestress force of 550 KN. Pe= 0.85Pi 3. Determine the eccentricity of the prestress force at the fixed end such that the resulting stress at the top fiber of the beam at the fixed end is zero a. 213.84 mm b. 114.98mm c. 316.13mm d. 284.98mm e. None
A suspension cable is supported at A and B, 120 m. horizontally apart with B higher than A by 15 m. The cable subjected to horizontal uniform load of 10 kN/m and sags a distance of 10 m. measured from the chord joining A and B at the midspan, compute the horizontal reaction at the supports.
Highway uniform load = 100 kN/m; highway point load = 200 kN; uniform dead load = 30 kN/m; point dead load at midspan = 50 kN. A. Calculate the maximum bending moment and shear at a point 4m from the left support. B. Calculate the maximum shear and moment at a point 6m from the left support.
Determine the maximum bending moment that can occur at a point 8 m from the left support of a simply supported beam of 24 m span when the following series of wheel-loads traverses the beam from the left: Note: Take the 10 KN at the right as the front-wheel load. Determine also the absolute maximum bending moment that can occur in the beam.
Determine the maximum bending stresses for a rectangular beam (20x40cm) subjected to a bending moment Mz = 60 kN.m.