polyethylene having an ultimate tensile strength of 3200 psi and an ultimate bearing strength of 1500 psi. The bolts are made of nylon that has an ultimate shear strength of 4400 psi. Determine the allowable load P for this connection if a safety factor of 3.7 is required. Consider tension and bearing in the bars and shear in the bolts. Disregard friction between the plates.

polyethylene having an ultimate tensile strength of 3200 psi and an ultimate bearing strength of 1500 psi. The bolts are made of nylon that has an ultimate shear strength of 4400 psi. Determine the allowable load P for this connection if a safety factor of 3.7 is required. Consider tension and bearing in the bars and shear in the bolts. Disregard friction between the plates.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter3: Tension Members

Section: Chapter Questions

Problem 3.5.1P

See similar textbooks

Similar questions

an angle bar 100x100x11 mm tension member is connected with 20-mm-dia bolts as shown in the fig. both legs of the angles are connected. use fy=248 MPa and Fu=400 MPa. 1. determine the nominal strength for tensile yielding in the gross section. a. 515.59 kN b. 429.67 kN c. 545.60 kN d. 390.10 kN 2. determine the effective net area of member a. 1573 mm^2 b. 1632 mm^2 c. 1605 mm^2 d. 1815 mm^2 3. determine the nominal strength for tensile rupture in the net area. a. 642 kN b. 730 kN c. 554 kN d. 650 kN
The figure shows a truss and the detail of the riveted connection at joint H. Using allowable stresses ofτ = H MPa and σb= I MPa, how many 19-mm diameter rivets are required to fasten member HB to thegusset plate? Member HC? Round-up your answer to a whole number F=162 H=110 I= 180
If the 18 mm plate is connected to two cover plate of 10 mm on top and bottom, what is the capacity of the connection in double shear? Assume that the shear planes pass though the threaded portion. State the condition necessary for these strengths to be available. (Draw the connect first and calculate the capacity)
A 15" x 3/8" bar of A572 Gr. 50 steel is used as a tension member. It is connected to a gusset plate with 7/8-in diameter bolts as shown in the figure. Use s = 2.0 and g = 3.0.a) Determine the design tensile strength of the section based on yielding of the gross area.b) Determine the critical net area of the connection shown.
For the clevis connection shown, the shear stress in the 0.287-in.-diameter bolt must be limited to 29 ksi. Determine the maximum load P (in kips rounded to the nearest hundredths) that may be applied to the connection.
The plate shown is attached by using three M12x2 grade 8.8 bolts. Which screw is subjected to the largest stress? What safe load ( static) F can be supported by the screw for n=1.5.
Pls answer thank you! A flange bolt coupling has 10 steel coupling 1 inch diameter bolts evenly tighten around a 16.34 in. bolt circle. Determine the torque capacity of the connection if the allowable shearing stress in the bolt is 7.3 ksi?
If the clamping force on the boards is 600 lb, determine the required magnitude of the couple forces that must be applied perpendicular to the lever AB of the clamp at A and B in order to loosen the screw. The single square threaded screw has a mean diameter of 2 in and a lead of 0.25 in. The coefficient of friction is 0.3.
A 3/4 in (thickness) X 5 in (height) steel plate is connected to another one through two bolts of nominal diameter 1/2 in in a zig-zag arrangement as shown. Determine the tensile strength capacity Pu of the connection. Review the three limit-states: (a) yielding in the gross area, (b) rup- ture in the overall net tensile area, and (c) block shear strength.
A staggered riveted connection has rivets arranged as shown below. The plate is 400 mm and 12 mm thick with four bolt holes. The diameter of rivet is 34 mm The diameter of the rivet hole is assumed to be 5 mm larger than rivet diameter. Fy = 248 MPa. Fu= 410 MPa, Fv in rivets is 372 MPa. 1. Which of the following gives the distance b so that the net area in section 1 – 2 – 3 – 4 equal to the net area in section 1 – 2 – 4 a. 30.01 mm b. 25.12 mm c. 19.7 mm d. 12.23 mm 2. Which of the following gives the net area using the computed value of b. a. 4622.65 mm² b. 5623.75 mm² c. 3623.64 mm² d. 7652.85 mm² 3. Which of the following gives the maximum tensile force that the connection could carry if the allowable yield stress is Fy/1.67. a. 432.12 kN b. 724.73 kN c. 253.25 kN d. 712.81 kN 4. Which of the following gives the maximum tensile force that the…
Two steel plate tension members have been connected using 0.72” diameter bolts arranged in an equally-spaced four by four square formation.Total plate self-weight is specified as 912 pounds.Design of the elements adhered to the set of values that are twice as much as the minimum requirements. Both plates have a thickness equal to 1/3 in. Take shear fracture stress as 54ksi and the min required edge distance as 0.125ft. a)Sketch the connection showing all the details and measurements with units. b)Find the maximum allowable service dead load(excluding the self-weight)and live load assuming live load is half as much as dead load including the self-weight of the plates.
The riveted lap connection shown consists of two(2) – PL 12 mm × 280 mm. 1. If allowable bearing stress in holes is 1.2Fu where Fu is the ultimate strength of the plate and which is equal to 400 MPa, find the maximum allowable force P that can be applied neglecting effect of eccentricity. a. 563.3 kN b. 460.8 kN c. 683. 6 kN d. 405.9 kN 2. If allowable yielding of gross area is Fy/1.67, where Fy is the yield strength of the plate and which is equal to 250 MPa, find the maximum allowable force P that can be applied neglecting effect of eccentricity. a. 534 kN b. 560 kN c. 446 kN d. 503 kN 3. If diameter of hole equals diameter of rivet, what is the net area of edge-3-4-edge in square millimeters? a. 2540 b. 2590 c. 2880 d. 2040