Answer the problem given the figure 5. Which of the following statements BEST describes the stability and determinacy of bent bar ABC?Bent bar ABC is unstable with concurrent reactionsBent bar ABC is statically indeterminate.Bent bar ABC is statically stable and determinate.Bent bar ABC is unstable with less than 3 unknowns◆ Consider the bent bar ABC shown in the figure shown. It is supported by a roller at A and a pin at B, and is loadedmoment M = 95 kN-m, an upward force Q = 6 kN, and a downward force P = 8 kN. Use L =by a counterclockwise7 m.LMB√3C

Answered: Image /qna-images/answer/39e7ce10-8ce2-4cc4-b5dd-6cdcde0456bf.jpg

Consider the bent bar ABC shown in the figure shown. It is supported by a roller at A and a pin at B, and is loaded moment M = 95 kN-m, an upward force Q = 6 kN, and a downward force P = 8 kN. Use L = by a counterclockwise 7 m. L M B √3 C

Consider the bent bar ABC shown in the figure shown. It is supported by a roller at A and a pin at B, and is loaded moment M = 95 kN-m, an upward force Q = 6 kN, and a downward force P = 8 kN. Use L = by a counterclockwise 7 m. L M B √3 C

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.4.14P: A crane boom of mass 450 leg with its center of mass at C is stabilized by two cables AQ and BQ (Ae=...

See similar textbooks

Related questions

Q: A Fo the two trusses shown. D G B O H P I P E C A o Do Go P C F B OE OH

A: Conditions for zero force members are: If at joint only three members meet,out of which two are…

Q: Determine the largest weight of the oil drum that the floor crane can support without overturning.…

A: For the largest weight of drum, the crane is about to overturn. It means there will be no contact of…

Q: A single block brake, as shown in Fig. 25.38, has the drum diameter 250 mm. The angle of contact is…

A: Given : d = 250 mm μ = 0.35 T = 70 Nm P = ? from the figure , angle of contact 2θ = 90 ∴ θ = 45⁰

Q: 2. The equations of motion of this system are; 12Y+7Y+24Y-62-122-0 62"+62+122-6Y-12Y=f(t)…

A: Given,

Q: 900 B 1000 mm 200 500 mm mm 215 mm

A: Given,

Q: A piece of chromium steel of length 7.4 cm (density = 8780 kg/m^3; k = 50 w/mK and specific heat cp…

Q: 3- The rectangular beam ABC, 100 mm wide by 400 mm deep, is supported by a pin at A and the cable…

A: The given information in the problem is represented in the following attached image:

Q: A 60 mm thickness large steel plate (k=42.6 W/m deg C, alpha = 0.043 m^2/h), initially at 440 deg C…

Q: Consider two types of thermal barrier coatings made of Zirconia. The first A is pure Zirconia and…

A: Given question is related to surface treatments and coatings.

Q: Problem (Rotating Vessel) A 1.90 m diameter closed cylinder, 2.75 m high is completely filled with…

A: To find: The angular speed of the vortex and the pressure force exerted on the side of the tank.…

Q: An open cylindrical tank 1.2 m in diameter and 1.8 m deep is filled with water and rotated about its…

Q: A solid steel shaft 5 m long is stressed to 60 MPa when twisted through 4 degrees. Using G = 83 GPa,…

Q: 3. Find the young's modulus of a bars a rod of diameter 25 mm and of length 250 mm which is…

Q: 5. What is the minimum diameter at section (1) in the pipe below to avoid cavitation at that…

A: Given Diameter, D2 = 15 cm Height, h = 5 m Find Minimum diameter, d

Q: A sample of cross-linked natural rubber (polyisoprene) is found to have a shear modulus of 100 kPa…

Q: 2.15 Air undergoes two processes in series! Process 1-2: polytropic compression, with n=1.3, from…

Q: The doorstop experiences trapezoidal pressure distribution in the friction pad, as shown in the…

Q: locate the X-X and Y-Y centroidal axes for the areas shown.

Q: • Ex3.PS4: Determine the force in members GF, FB, and BC of the Fink truss and state if the members…

Q: A pressurized water tank supplies water to a hose. The tank has a pressure of 155 kPa and the hose…

A: Given : inside tank conditions : p₁ = pgauge = 155 kpa V₁ = 0 (water in tank is stationery) z₁ = 0…

Q: 2.13 A gas expands from an initial state where p 500 kPa and V= 0.1 m² to a final state where P₂ =…

A: Given data: P1=500 KpaP2=100 KpaV=0.1 m3PV=constant

Q: A spring with ends squared and ground, wire diameter d = 4 mm, outside diameter Do = 40 mm, 18 total…

Q: USE YOUR OWN ESTIMATES FOR MASS , VELOCITY ETC .If a vehicle has to decelerate because another…

A: Let the mass of the vehicle is m kg and initial velocity of the vehicle is V m/s The vehicle is…

Q: рабоваг P= lo5 bar 1.5

A: Given-Information:- p = 60 barp = 1.5 barT0 = 300 Kp0 = 1 bar To-Determine:- a. % isentropic turbine…

Q: A cold air-standard Otto cycle has a compression ratio of 9 and the temperature and pressure at the…

Q: Three springs are arranged in parallel like the configuration shown in (Figure 1). They have spring…

Q: A river barge, whose cross section is approximately rectangular, carries a load of grain. The barge…

Q: Given two views, draw the missing view and the isometric of the solid. L HRP FRP FRP PRP F

A: Given: Two views, draw the missing view and isometric view of the solid.

Q: The pressure at which the steam should be reheated. Notes:  Assume the steam is reheated to the…

A: To find: The reheater pressure. Given: The pressure at the entry of the high-pressure turbine is…

Q: Determine the centroid coordinates of the shaded surface

Q: Steam is supplied to a fully loaded 100-hp turbine at 276 psia with u1=1,220.3 Btu/lbm, v1=3.65…

A: Given : p₁ = 276 psia u₁ = 1220.3 Btu/lbm v₁ = 3.65 ft³/lbm υ₁ = 466 ft/s p₂ = 3 psia u₂ = 943…

Q: a. Resultant of the non-concurrent forces b. Magnitude of the moment at point A. c. Location of…

Q: age 111 Practice Problem 4.8: If we double the mass of the chain, what are the new values for e…

A: Given Initial Mass, m1 = 10 kg Final mass (after doubled), m2 = 20 kg…

Q: In a paragraph, explain: What is the difference between energy transfer and energy transformation

A: Introduction The ability to accomplish work is defined as energy. It is one of the most basic human…

Q: Problem 8.4 A single-threaded square power screw is 0.5 inches in diameter with a pitch of 0.125…

A: The given data in the question is shown in the following attached image:

Q: Given two views of a solid, draw the missing view and the isometric of the solid.

A: Find Draw the missing view and the isometric view of the given object.

Q: Given the views in HRP and PRP, provide the FRP view and isometric view of the figure.

A: Given: The views in HRP and PRP, provide the FRP view and isometric view of the figure.

Q: A hollow spherical steel has an inner diameter of 30cm and outer diameter of 37cm. It is covered…

A: Given:Inner diameter of sphere, di=30 cmOuter diameter of sphere, do=37 cmThickness of insulation,…

Q: Water flowing in a smooth 6-cm-diameter pipe enters a venturi contraction with a throat diameter of…

A: Given data:- Diameter of the pipe =6 cm throat diameter =3 cm upstream pressure =120 kPa flow rate…

Q: Drag. To see why golf balls are rough, estimate the terminal speed of a golf ball falling through…

A: Given data: Mass of the ball = M = 0.05 kg Diameter of the ball = D = 0.05 m Find: Calculate the…

Q: A stream of methane(CH4, Cp=4R) flowing at 3.0 kmol/min is isobarically heated in a well‑insulated…

A: Given: For Methane m˙=3 kmol/min=0.05 kmol/sCp=4R=4×8.314 kJ/kmolK=33.256 kJ/koml…

Q: -6m -8 m ·3₂ -12 m B₂ 2.4 kN. D 10 m

Q: A gaseous fuel has he following composition by volume – CH4 = 25%, CO= 10%, H2= 6%, C3H8=10%.…

Q: Consider a mass-spring system. The spring has a spring constant of 2.35e+3 N/m. On the end of the…

Q: A cup of hot coffee whose temperature is 200°F is poured in a room whose temperature is 70°F. Two…

A: Given : case 1 : T₀ = 200⁰ F T∞ = 70⁰ F Tf = 180⁰ F t = 2 minutes = 120 seconds case 2 : T₀ =…

Q: 282N 1m 200N 1m B A 360N

A: Given,

Q: An unknown gas at p1=95psia and V1=4 ft3undergoes a process to p2=15psia and V2=16.56 ft3, during…

A: Given : p₁ = 95 psia V₁ = 4 ft³ p₂ = 15 psia V₂ = 16.56 ft³ dH = -83 Btu (- ve since decreased)…

Q: The dimensions of the four bar mechanism of P1ABP2 as follows: P1A=300mm; AB=580mm; P2B=360mm; and…

Q: The state at the beginning of compression of an air-standard Diesel cycle is fixed by p₁ = 100 kPa…

A: Given:The state of air at the beginning of comression, P1=100 kPa, T1=310 KCompression ratio,…

Q: Which of the following is TRUE on what right a patent gives the IP owner? The right to infringe…

A: A patent is a type of intellectual property that gives the owner the right to exclude others from…

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

Answer the problem given the figure

5. Which of the following statements BEST describes the stability and determinacy of bent bar ABC?
Bent bar ABC is unstable with concurrent reactions
Bent bar ABC is statically indeterminate.
Bent bar ABC is statically stable and determinate.
Bent bar ABC is unstable with less than 3 unknowns
◆

Consider the bent bar ABC shown in the figure shown. It is supported by a roller at A and a pin at B, and is loaded
moment M = 95 kN-m, an upward force Q = 6 kN, and a downward force P = 8 kN. Use L =
by a counterclockwise
7 m.
L
M
B
√3
C

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Two pipe columns (AB, FC) are pin-connected to a rigid beam (BCD), as shown in the figure. Each pipe column has a modulus of E, but heights (L1or L2) and outer diameters (d1or different for each column. Assume the inner diameter of each column is 3/4 of outer diameter. Uniformly distributed downward load q = 2PIL is applied over a distance of 3L/4 along BC, and concentrated load PIA is applied downward at D. (a) Derive a formula for the displacement
.17 A mountain-bike rider going uphill applies torque T = Fd(F = l5lb, d = 4 in.) to the end of the handlebars ABCD by pulling on the handlebar extenders DE. Consider the right half of the handlebar assembly only (assume the bars are fixed at the fork at A). Segments AB and CD are prismatic with lengths L, = 2 in.andL3 = 8.5 in, and with outer diameters and thicknesses d01 = 1.25 in. 101 = 0.125 in. and d03 = O.87in.,i03 = 0.ll5in, respectively as shown. Segment BC’ of length L, = 1.2 in. however. is tapered, and outer diameter and thickness vary linearly between dimensions at B and C. Consider torsion effects only. Assume G = 4000 ksi is constant. Derive an integral expression for the angle of twist of half of the handlebar tube when it is subjected to torque T = Fd acting at the end. Evaluate ‘b1-, for the given numerical1ues.
A soccer goal is subjected to gravity loads (in the - z direction, w = 73 N/m for DG, BG, and BC; w = 29 N/m for all other members; see figure) and a force F = 200 N applied eccentrically at the mid-height of member DG. Find reactions at sup ports C, D, and H.
A post AB supporting equipment in a laboratory is tapered uniformly throughout its height H (see figure). The cross sections of the post are square, with dimensions b × b at the top and 1.5b × 1.5b at the base. Derive a formula For the shortening 8 of the post due to the compressive load P acting at the top. (Assume that the angle of taper is small and disregard the weight of the post itself.)
A T-frame structure is torn posed of a prismatic beam ABC and a nonprismatic column DBF. The beam and the column have a pin support at .A and D, respectively. Both members are connected with a pin at B. The lengths and properties of the members are shown in the figure. Find the vertical displacement of the column at points F and B. Plot axial force (AFD) and axial displacement (ADD) diagrams For column DBF.
A hollow circular tube T of a length L = 15 in. is uniformly compressed by a force P acting through a rigid plate (see figure). The outside and inside diameters of the tube are 3.0 and 2.75 in., respectively. A concentric solid circular bar B of 1.5 in. diameter is mounted inside the lube. When no load is present, there is a clearance c = 0.0I0 in. between the bar B and the rigid plate. Both bar and tube are made of steel having an c[autoplastic stress-strain diagram with E = 29 X LO3 ksi and err= 36 ksi. (a) Determine the yield load Pt- and the corresponding shortening 3yof the lube. (b) Determine the plastic load Ppand the corresponding shortening Spof the tube. (c) Construct a load-displacement diagram showing the load Pas ordinate and the shortening 5 of the tube as abscissa. Hint: The load-displacement diagram is not a single straight line in the region 0 ^ P ^ Pr
The upper deck ala foothill stadium is supported by braces, each of which transfer a load P = 160 kips to the base of a column (see figure part a). A cap plate at the bottom of the brace distributes the load P to four flange pates (:1 = I in)t hrough a pin(d, = 2 in.) to two gusset plates t8 = l.5 in.) (see figure parts b and c). Determine the following quantities. (a) The average shear stress i in the pin. (b) The average bearing stress between the flange plates and the pin and also between the gusset plates and the pin Disregard friction between the plates. Determine the following quantities. (a) The average shear stress i in the pin. (b) The average bearing stress between the flange plates and the pin and also between the gusset plates and the pin (7j )L Disregard friction between the plates.
A long, slender bar in the shape of a right circular cone with length L and base diameter d hangs vertically under the action of its own weight (see figure). The weight of the cone is W and the modulus of elasticity of the material is E. Derive a formula for the increase S in the length of the bar due to its own weight. (Assume that the angle of taper of the cone is small.)
Bar ABC is fixed at both ends (see figure) and has load P applied at B. Find reactions at A and C and displacement SBif P = 200 kN. L = 2 m, t = 20 mm, b, = 100 mm, b2= 115 mm, and E = 96 GPa.
A plane Frame with pin supports at A and E has a cable attached at C, which runs over a friction-less pulley at F(see figure). The cable Force is known to be 500 lb. (a) Find reactions at supports A and E. (b) Find internal stress resultants N, V, and M at point H.
A rigid bar AB having a mass M = 1.0 kg and length L = 0.5 m is hinged at end A and supported at end B by a nylon cord BC (see figure). The record has cross-sectional area A = 30 mm2. length b = 0.25 m. and modulus of elasticity E = 2.1 GPa. If the bar is raised to its maximum height and then released, what is the maximum stress in the cord?
A mountain bike is moving along a flat path at constant velocity. At some instant, the rider (weight = 670 N) applies pedal and hand forces, as shown in the figure part a. (a) Find reaction forces at the front and rear hubs. (Assume that the bike is pin supported at the rear hub and roller supported at the front hub.) (b) Find internal stress resultants N, V, and M in the inclined seat post (see figure part b