USE YOUR OWN ESTIMATES FOR MASS , VELOCITY ETC .If a vehicle has to decelerate because another vehicle merged into its lane, estimate the kinetic energy the vehicle that slowed down by 7m/s to match the other vehicle's speed experienced. Show this answer in joules and as a percentage change in the vehicle's total kinectic energy and explain your reasoning

USE YOUR OWN ESTIMATES FOR MASS , VELOCITY ETC .If a vehicle has to decelerate because another vehicle merged into its lane, estimate the kinetic energy the vehicle that slowed down by 7m/s to match the other vehicle's speed experienced. Show this answer in joules and as a percentage change in the vehicle's total kinectic energy and explain your reasoning

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter1: Introduction To Statics

Section: Chapter Questions

Problem 1.19P: Plot the earths gravitational acceleration g(m/s2) against the height h (km) above the surface of...

See similar textbooks

Similar questions

Hi please help me answer this with drawing, thank you. Plot a displacement diagram for a body that is to rise and fall as follows; rise 1 in. in 4 seconds with uniform acceleration, rise 1 in. in 4 sec. with uniform retardation, rest 6 seconds, fall 1 ¼ in. in 6 sec with harmonic motion, rise ½ in. in 3 sec with uniform velocity, fall 1 ¼ in. at once, and rest 4 sec.. Plot displacement as ordinates full size and the time as abscissas to a scale of 1 in. = 4 sec.
Please include explanation. A 6-MW offshore wind turbine has a capacity factor of 40%. It has a height of 120 m, and 107-m long blades. The angular acceleration is 1.388 rad/s2. Assume that the distance from the center of the turbine to the connection with the blade is negligible, and that the turbine starts from rest. At ? = 12 s, calculate the velocity and the acceleration for points (a) at half the length and (b) at the tip of the blade.
The 100 meter diameter wheel needs to be designed so that it rotates at a constant rate and every complete revolution takes 15 minutes. The wheel has been installed in a vertical plane and the lowest seat is 2m above the ground surface. Each ride consists of only one full rotation. Find a further general expression for the horizontal displacement of the rider from its initial position with respect to both time and angle of rotation and hence determine the speed of the rider when t= 180 sec. Using calculus, determine what the maximum horizontal and vertical speeds of the rider would be and at which points during the ride they occur. State expressions for the acceleration of the rider in both horizontal and vertical directions and show that the resultant acceleration experienced by the rider is independent of where on the ride he/she might be. In designing a new wheel with the same diameter and same ride duration as before it is proposed that the wheel’s angular speed should not…
Given: lambda = 10 m, mass of the vehicle, m= 1000kg, k=9000 N/m, speed 60/2pi m/s. Interpret this graph for me. What happens if we go to the right? What happens if we go to the left? If we want to have a great magnitude of vibrations according to the graph should we increase or decrease our speed? explain. What if b is decreasing but we maintain our speed would b decrease or increase the magnitude? Why? If we are driving at the speed that always maximizes the magnitude of the shaking will decreasing b increase or decrease magnitude?
The moment of the torpedo control unit in water was tested with a 1:8 scale scale model in a water tunnel of identical properties with a speed of 20 m/s if the measured moment in the model was 14 Nm. calculate 1) Determine the velocity of the prototype using the Reynolds number analogy. 2) Find the ratio of the forces occurring in the model and prototype. Using the analogy of Euler number 3) find the moment that occurred with the prototype.
1. average velocity is correct (-0.75 m/s) but instantaneous velocity (-1 m/s) is incorrect can you help me?
A child applies a push on his toy car causing it to move horizontally. He controls his applied push such that the x-component Fx varies with the toy’s displacement according to the graph below. What is the total work done by Fx as the toy car moves from x = 0 to x = 15m?
Two blocks connected by a string are pulled across a horizontal surface by a force applied to one of the blocks, as shown below. The coefficient of kinetic friction between the blocks and the surface is 0.25. If each block has an acceleration of 2.0 m/s2 to the right, what is the magnitude F of the applied force?
Calculate the piston travel, velocity, and acceleration for an engine with R= 50 mm and lrod=170 mm using the equation and graphical representation and compare the results (take 45o increment ,N= 3000 r.p.m).
TOPIC: Equation of Motion (NORMAL AND TANGENTIAL) Fn= Man Ft= Mat Given a 1400 kg car that travels along a road with increasing vertical profile y = 0.0003x². If the constant velocity of the car is 30 m/s. of the distance is at 210m, Determine the x-component of the velocity (m/s) of the car. Compute the total force (KN). PLEASE ANSWER WITH A COMPLETE AND DETAILED SOLUTIONS. THANK YOU
Using the image on the Moment of Inertia Tab, where the following criteria are considered:Assign the values to “Apply torque” = 2 Nm, “Brake force” fr = 0.2 N. “Platform Mass” m= 0.25 kg.Use"radians" for angle units. Write down the values that appear in the graphs of torque, a moment of inertia, and angular acceleration. Then, obtain the other physical quantities by applying the equations of rotational dynamics that correspond to:Time:4.5Applied torque:2 N-mBrake torque:Net torque:Angular impulse:Moment of inertia:Angular acceleration:Initial angular velocity:Final angular velocity:
C1 (a) A plate 0.05mm distant from a fixed plate moves at 1.15 m/s and required a force per unit area of 2.2 N/m2 to maintain this speed with using an oil of specific gravity 0.75. Find the dynamic viscosity and kinematic viscosity of the fluid between the plates. C1 (b) Calculate the specific weight, density, and the specific gravity of a liquid having a volume of 665000 cm3 and weight of 72 kN find : C1 (a) 1_The dynamic viscosity of the fluid (in Centipoise) 2_The kinematic viscosity of the fluid (in stokes) C1 (b) 3_Specific Weight in (N/m3) 4_Density of liquid (in kg/m3) 5_Specific gravity of liquid