Consider the cantilevered W14 x 30 beam shown in(Eigure 1). E-29(10) ksi, I-291 inFigure<10f1SkipPart ADetermine the expression for the elastic curve using the coordinate z for 05a59ft, where is in feetExpress your answer in terms of z. Express your answer using three significant figures.AX+ IT vecSubmit Previous Answers Request AnswerX Incorrect; Try Again; 5 attempts remainingPart BDetermine the maximum slope of the beam, measured counterclockwise from the positive z axisExpress your answer using three significant figuresVAX IvecPrevious Arawers Request AcaX Incorrect; Try Again; 5 attempts remainingSubmitft?rad

Given: w=3 kip/ft E=29 (103) ksi I = 291 in4

Consider the candlevered W14 x 30 beam shown in (Egure 1). E=29(10³) ksi, I-291 in Figure 369 Part A Determine the expression for the elastic curve using the coordinate z for 05a59ft, where is in feet Express your answer in terms of z. Express your answer using three significant figures. ΕΘΕΙ ΑΣΦ. itavec Submit Previous Answers Request Answer * Incorrect; Try Again; 5 attempts remaining Part B Submit Determine the maximum slope of the beam, measured counterclockwise from the positive z axis Express your answer using three significant figures. VALIvec Previous Arawers Request Acamer ? X Incorrect; Try Again; 5 attempts remaining ft

Consider the candlevered W14 x 30 beam shown in (Egure 1). E=29(10³) ksi, I-291 in Figure 369 Part A Determine the expression for the elastic curve using the coordinate z for 05a59ft, where is in feet Express your answer in terms of z. Express your answer using three significant figures. ΕΘΕΙ ΑΣΦ. itavec Submit Previous Answers Request Answer * Incorrect; Try Again; 5 attempts remaining Part B Submit Determine the maximum slope of the beam, measured counterclockwise from the positive z axis Express your answer using three significant figures. VALIvec Previous Arawers Request Acamer ? X Incorrect; Try Again; 5 attempts remaining ft

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter9: Deflections Of Beams

Section: Chapter Questions

Problem 9.9.7P: The cantilever beam A CB shown in the hgure is subjected to a uniform load of intensity q acting...

See similar textbooks

Similar questions

For the simply supported beam carrying the concentrated load P = 276 N at its midspan, determine the magnitude of the maximum slope angle of the beam (in degrees) if d = 2.16 m, E = 12.77 GPa , and I =1681393mm4. NOTE: PLEASE ANSWER IT CORRECTLY. IF YOU ARE NOT SURE ABOUT THE ANSWER, PLEASE SKIP THE QUESTIONPLEASE BOX THE FINAL ANSWER(S)THANK YOU!
Determine the deflection at Point C of the beam shown below (negative is down). P = 16 kN wo = 29 kN/m E = 192 GPa I = 94.145x10-6 m4 Express your answer using three significant figures and ensure that it is in mm.
In the beam, which is given the loading and supporting status below a) Find the location of the largest crash and the value of the crash. b) What is the maximum length of the beam (L) so that the largest collapse value is less than 1.5 mm? E = 210 GPa Mo = 250 kNm I = 556x10-6 m4
For the simply supported beam carrying the concentrated load P = 268 N at its midspan, determine the magnitude of the maximum displacement (in mm) if d = 1.51 m, E = 11.77 GPa , and I =1679930mm4. NOTE: PLEASE ANSWER IT CORRECTLY. IF YOU ARE NOT SURE ABOUT THE ANSWER, PLEASE SKIP THE QUESTIONPLEASE BOX THE FINAL ANSWER(S)THANK YOU! image below for reference
The beam safely supports shear forces and bending moments of 2kN and 6.5 kN-m respectively. Based on this criterion, can it be safely subjected to the loads F = 1kN and C = 1.6 kN-m? Use the area method
Determine the equivalent stiffness of a cantilever beam which is loaded transversely on its end and has a length in 5000 mm and an annular cross section with inner and outer diameters of 25 mm and 22 mm, respectively. The modulus of elasticity of the beam is 72x109 N/m2. Use moment of inertia I=π(D4o−D4i)/64 and spring constant is (k= 500 N/m). Answer must be in three decimal places.
determine the deflection at B in mm using Conjugate Beam Method. Consider 150 mm x 200 (b x h) mm section and E=80 GPa. Enter the absolute value only and round off your answer to 3 decimal places Answer asap. I rate
the W14 x 43 simply supported beam is made of A-36 steel and is subjected to the loading shown where the distributed load is equal to 2.40 kip/ft. Ix = 428 in4 , E=29 (103) kip determine the beam's deflection at its center, C. give your answer as a signed distance, where up is positive.
Please help me for the correct solution. A leaf spring carries a central load of 3000 N. The leaf spring has to be made of 10 steel plates 5cm wide and 6mm thick. If the bending stress is limited to 150 N/mm² determine: (i) Length of the spring and (ii) Deflection at the centre of the spring. Take E = 2 * 10 ^ 5 * N / m * m ^ 2..?
Given the 200mm x 400mm beam with the loading shown, determine: a. the amount of load P applied on the beam if the deflection on the midspan is 5 mm downward. b. by this same load P, what is the deflection and slope on the beam at point D? Set the parameters as a = 3m, L = 9m , E = 200 GPa. EI is constant.
Determine the largest intensity of the distributed load ww and its length xx on the beam so that the beam remains in the horizontal position when it is loaded. Express your answers, separated by a comma, to three significant figures. Given: The rigid beam is supported at its ends by two A-36 steel tie rods. (Figure 1) The rods have diameters dAB=0.51 in.dAB=0.51 in. and dCD=0.29 in.dCD=0.29 in. The allowable stress for the steel is σallow=16.6 ksiσallow=16.6 ksi.
The beam is made of southern pine for which Ep = 13 GPa. Determine the displacement at A.