Consider the circuit diagram below, where: v1(t) = 12 cos(377t) v2(t) = 5 cos (377t) Use node analysis to determine the voltage at nodes a and b. Express the voltages as sinusoids in the time domain with phase angles measured in degrees. R1 3 kN R2 8 kN C1 450 nF а ww ww + v¼(t) C2 L1 v2(t) 600 nF 5 H

Consider the circuit diagram below, where: v1(t) = 12 cos(377t) v2(t) = 5 cos (377t) Use node analysis to determine the voltage at nodes a and b. Express the voltages as sinusoids in the time domain with phase angles measured in degrees. R1 3 kN R2 8 kN C1 450 nF а ww ww + v¼(t) C2 L1 v2(t) 600 nF 5 H

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A series circuit of RLC with following parameters, R=15 ohm, L=20 m H & C=100 micro Farad. VT=169.7 sin (337t-30) Volt. Find the following: Zt, , It, Voltage across each element, Power factor, apparent power, real or average power and reactive power and the total phasor diagram and power phasor diagram
The total impedance Z, of a circuit containung an inductor with inductance L and resistance R in series is given by Z  R  j2fL where f  frequency . If Z  (50  j200)ohm and f = 50Hz. Find R and L
Suppose that the modulating signal m (t) is sinusoid of the formm (t) = 10 COS ( 2π103t) and the carrier signal C(t) is sinusoid of the form C(t) = 4 COS ( 2π106t + Ɵ)1. According to the previous results which type of AM is the best in respect toa. Power transmitted b. band widthJustify your answers2. Draw the block diagram for both DSBSC and DSBFC with all parameters.
A 90-ohm resistor, a 32 mH inductor, and a 5 uF capacitor are connected in series across the terminals of a sinusoidal voltage source, vs = 125∠-60° V. If the angular velocity is ω = 5000 rad/s, find: a. The value of capacitance that yields a steady-state output current i with a phase angle of -105°. Express your answer in 2 decimals. b. The magnitude of the steady-state output current i. Express your answer in the nearest whole mA.
Three branches having impedances of 3+j4 Ω, 16−j12 Ω, and−j4 Ω, respectively, are connected in parallel. What are the equivalent(a) admittance, (b) conductance, and (c) susceptance of the parallelconnection in millisiemens? (d) If the parallel branches are excited froma sinusoidal current source where i=8 cosωt A, what is the maximumamplitude of the current in the purely capacitive branch?
Consider the circuit diagram below. Compute the impedances for all circuit components, i.e. ??1, ??2, ??3, ??1, ??1, for (a) ? =60 Hz, (b) ?=100 Hz. For both (a) and (b), redraw the circuit diagram with the computed impedances indicated. Express your final answers as a phasors with rectangular coordinates. You must show your all your work for the complex math
Exercise 11) Transform the circuit in phasor domain representation2) Determine the value of total impedance, ZT3) Determine the value of total current, IT4) Determine the value of voltage across resistor and capacitor5) Convert in rms values.
five infinite-impedance volunteers,calibrated to read rms values,are connected as shown below. let R= 200, L=0.400H,C=6.0 Mf, and V=30.0 v. what's the reading of the voltmeter's V1,V2,V3,V4 and V5 if W= 200 rad/s
The device is represented in the frequency domain bya Norton equivalent. When a resistor having an impedance of 5 kΩ isconnected across the device, the value of V0 is (5–j15) V. When acapacitor having an impedance of −j3 kΩ is connected across the device,the value of I0 is (4.5–j6) mA. Find the Norton current IN and theNorton impedance ZN
A 200V, 50 Hz sinusoidal supply is connected to a parallel network comprising three branchesA, B and C as follows: A, a coil of resistance 3 ohm and inductive reactance 4 ohm; B, a seriescircuit of resistance 4 ohm and capacitive reactance 3 ohm; C, a capacitor. Given that the powerfactor of the combined circuit us unity, find (a) the capacitance of the capacitor inF; (b) the current taken from the supply. [Ans. 127.32 F, 56A]
6.23 Find period, frequency, phase angle in degrees, and maximum, minimum, average, and effective values of vðtÞ ¼ 2 þ 6 cosð10t þ =6Þ. Ans: T ¼ 0:2 s; f ¼ 5 Hz; phase ¼ 308; Vmax ¼ 8; Vmin ¼ 4; Vavg ¼ 2; Veff ¼ ffiffiffiffiffi 22
For the circuit shown below, the initial conditions are zero, Vdc is a voltage source continuous and switch S is closed at t = 0.a)Determine the equivalent impedance to the right of points a and b of the circuit, Z(s).b)Obtain the input current of the circuit in the frequency domain, I(s). employ the properties of the initial and final value and calculate the values of i(0) and i(∞).c)Find the expression for i(t). Check if the values of i(0) and i(∞) agree with those calculated in the previous item.d)Obtain voltages v1(t) and v2(t).