Consider the closed-loop transfer function B+ kB2 T(s) = B3+ kB4 where B1, B2, B3, and B4 are constants. Compute the sensitivity of the system to variations in the parameter k. Select one: k(B-B2) (B3+kB)(B1+kB2) O a. k(B2B3-BB4) (B3-kB.)(B1-kB2) O b. k(B,B3+B,B) (B3+kB,)(B1+kB,) O C. k(B,B3-B,B) (B3+kBa)(B1+kB2) %3D O d. SE k(B3-kB,) (B1+kB2) %3D

Consider the closed-loop transfer function B+ kB2 T(s) = B3+ kB4 where B1, B2, B3, and B4 are constants. Compute the sensitivity of the system to variations in the parameter k. Select one: k(B-B2) (B3+kB)(B1+kB2) O a. k(B2B3-BB4) (B3-kB.)(B1-kB2) O b. k(B,B3+B,B) (B3+kB,)(B1+kB,) O C. k(B,B3-B,B) (B3+kBa)(B1+kB2) %3D O d. SE k(B3-kB,) (B1+kB2) %3D

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

We are now interested in studying the behavior of the rotating valve plate shaft on an ETC only. This is to evaluate the dynan1ic response of the valve plate as an input torque is given to its shaft. The valve-plate shaft can be modeled as shown in Figure 3. (a) Find the transfer function of G(s) = θ(s)/r(s) , then evaluate the stability of thesystem by identifying its poles and zeros. Plot the poles and zeros in an s-plane and characterize the step response damping type. (b) To design a responsive throttle response, the overshoot and settling time need to be set at a certain level. Considering that J and D of our system in Figure 3 can be modified, find the values of J and D to yield 20% overshoot and a settling time of 2 seconds.
Transformation from state-space representation to transfer function: [ num, den ] = ss2tf(A,B,C,D)
a)Describe nontouching graph to a forward path and list down all nontouching graph(s) of the obtained Signal Flow Graph.b)Describe all variables in Mason’s Rule Formulation.c)Find the transfer function C(s)/R(s) by using the equation. Show all seven (7) steps to obtain the transfer function.
For the block diagram shown in following figure, a) Find the transfer function between input (X) and output (Y) b) Check the stability of the system c) Find the transfer function of the system with PI, PD, and PID controller d) Find the step responses of the compensated system with PI, PD, and PID controller, and show the time-domain characteristics for each system
A hard disk drive (HDD) is an electro-mechanical data storage device that stores and retrieves digital data using magnetic storage and one or more rigid rapidly rotating platters coated with magnetic material. Figure 1 shows a simplified block diagram of a HDD. For analysis purposes, given gain K=30 and G(s)=1 / s(s+4) determine the open-loop and closed loop poles of the HDD and plot these separately in the S-Plane. Also discuss the stability using two different approaches.
Discuss the effect of increasing and decreasing proportional gain to the system output. Discuss the effect of increasing and decreasing derivative gain to the system output. Discuss the effect of increasing and decreasing the integral gain to the system output. 4. Discuss some advantages of using Simulink over the MATLAB codes I WANT THE ANSWER FOR THIS QUESTION WITHOUT PLAGIARISM
For this problem,Use Mason's gain Formula and then Find Over all Trans.function [Everything should be in handwritten format,please explain everything in detail including formula or else you can leave it ]
b) G(?)=K [(S−1)(S−2) / (S+2)(S+3)] ; Construct nyquist curves for K=1, 5/3, 9 values. Write down the Nyquist stability criterion and explain whether the system is stable or not. c) Define the gain and phase margin, this time on the nyquist curve.
Given the loop transfer f5555ufor any input6nplanection G(s)H(s)=K(s+6)/(s+3)(s+5).Thenumber of open-loop poles, P is a.0 b.3 c.2 d.1
For the discrete-time signal x[n] shown in Figure 4. Sketch and label carefully each of the following signals in picture
https://www.bartleby.com/questions-and-answers/an-input-voltage-of-230-v-is-applied-to-a-step-up-chopper-and-the-output-voltage-is-690-v.-the-pulse/d619e370-4db7-4680-8284-bd5aa5cb6d9c (I want answer on this link please)
There are cases when there is a zero in the first column while forming the Routh-Hurwitz table for a particular system. Describe how to modify the Routh-Hurwitz table that has one of the cases above using the transfer function of an open-loop system shown below as an example. G(s) =1000/ s5+ 2s4+ 3s3+ 6s2+ 5s + 3