Cable systemsQuestion 1Consider the diagram. The sag at point B is hɛ = 10cm. Calculate (a) the sag h, at point C and (b) thetension in BC.50 ст50 cm50 ст|<---->|<---->|<---->|DhBhcB400 N500 N

Name: Cable systemsQuestion 1Consider the diagram. The sag at point B is hɛ
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Cable systemsQuestion 1Consider the diagram. The sag at point B is hɛ = 10cm. Calculate (a) the sag h, at point C and (b) thetension in BC.50 ст50 cm50 ст| | | |DhBhcB400 N500 N

Answered: Consider the diagram. The sag at point…

Engineering

Mechanical Engineering

Consider the diagram. The sag at point B is hg = 10cm. Calculate (a) the sag h, at point C and (b) the tension in BC. 50 ст 50 cm 50 ст D hB he B 400 N 500 N

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.77P: The cable AOB weighs 5.2 N/m. When the horizontal 30-N force is applied to the roller support at B,...

See similar textbooks

Similar questions

A cable with supports at the same elevation has a span of 300m. The cable weighs 75 N/m and the sag at midspan is 75 m. Determine The length of the cable.
A dam with triangular cross section holds back a body of water. The dam has height h. The dam is made of concrete, which has speci…c gravity 3.1. What is the maximum angle, , for which thedam will not tip over about point O?
Fast pls solve this question correctly in 5 min pls I will give u like for sure Class: Structures 1 Question: locate the centroid of the box section shown, a cross-section often used in bridge construction Answers: Ax=0 Ay=3.92 kn By=11.08 kn Sub.
A cable with supports at the same elevation has a span of 550 ft. The cable weighs 4 lb / ft and the sag at midspan is 100 ft. Determine The length of the cable.
An aluminum block (SG-2.5) has a dimension of 0.1 m x 0.1 m x h meters. It is floating in mercury (SG-13.6) and the submerged height of the block is 0.90 m. Determine the weight (kN) of the block.
Find the magnitude and location of the resultant force on the cylindrical arc shown in Fig. (10) in each of the following two case: a. Pg=120.11 KPa (abs) b. Pg=90.68 KPa (abs) The arc is 25m long (normal to the paper)
The beam in the figures below has the cross section and loading indicated therein;determine for the most requested section, knowing that the allowable normal voltage is 1400kgf/cm².a) Determine the sum of forces in X, Y and Momentum
include also the free body diagram
A large block of wood has the shape of an isosceles trapezoid, as shown in the figure. The bottom end of the block has a width of ?b=1.75 m, and the top end has a width ?t=1.35 m. If the center of gravity of the block is located a distance ℎcg=1.13 m directly above the midpoint of the base, what is the maximum tipping angle that the block can undergo before tumbling over?
To test the validity of aerodynamic assumptions made in the design of the aircraft, its model is being tested in a wind tunnel. The support bracket is connected to a force and moment balance, which is zeroed when there is no airflow. Under test condition sS, the lift L, drag D, and pitching moment MG act as shown. The force balance records the lift, drag, an d a moment Mp. Determine MG in terms of L, D, and Mp.
A caisson for closing the entrance to a dry dock is of trapezoidal from 16 m wide at the top and 12 m wide at the bottom and 8 m deep. Find the total force in MN on the caisson if the water on the outside is 1 m below the top level of the caisson and the dock is empty. enclude your free body diagram. a.117.72 b.80.93 c.3.164 d.37.77
The concrete graviy" dam is heid in place by its awn weight (Egute.1) The density of concrote is pc=2.5Mg/m2 and water has a density of ρw=1.0Mg/m3. Suppose that a=1⋅m ,h=8 m Figure Part A Determinn the setillest dimension d that will prevent the dam hom overturning about is end A. Express your answer to three significant figures and include the appropriate units: d=_______