Consider the following double sampling plan. First select a sample of 5 from a lotof 100. If there are four or more defectives in the sample, reject the lot. If there isone or fewer defective, accept the lot. If there are two or three defectives, samplean additional five items and reject the lot if the combined number of defectives inboth samples is five or more. If the lot has 10 defectives, what is the probabilitythat a lot passes the inspection? For the double sampling plan described in Problem 39, determine the following:b. The probability that the lot is rejected based on the second sample.

Consider the following double sampling plan. First select a sample of 5 from a lotof 100. If there are four or more defectives in the sample, reject the lot. If there isone or fewer defective, accept the lot. If there are two or three defectives, samplean additional five items and reject the lot if the combined number of defectives inboth samples is five or more. If the lot has 10 defectives, what is the probabilitythat a lot passes the inspection? For the double sampling plan described in Problem 39, determine the following:b. The probability that the lot is rejected based on the second sample.

Practical Management Science

6th Edition

ISBN:9781337406659

Author:WINSTON, Wayne L.

Publisher:WINSTON, Wayne L.

Chapter10: Introduction To Simulation Modeling

Section10.2: Probability Distributions For Input Variables

Problem 2P: Use Excels functions (not @RISK) to generate 1000 random numbers from a normal distribution with...

See similar textbooks

Similar questions

A single sampling inspection scheme for large lot of mass-produced flanges states:From each lot take and inspect a random sample of 50. If 3 or more defectives, inspect the whole lot and remove all defectives, if less than 3 are found accept the lot without further inspection.a. Obtain the equation for Pa the probability that a lot containing a fraction p of defectives will be accepted, in terms of p.b. Evaluate Pa for p=0.01, 0.02, 0.03, 0.05, 0.07, 0.10, 0.15, 0.20, 0.30. Plotthe operating characteristics and average outgoing quality curve.c. Estimate: (a) the producer’s Risk at p of 2% (b) the consumer’s Risk for pof 5%.
The general meaning of a standard error is best described by which of the following? a. A standard error is another term for the estimated standard deviation of the population. b. If you go out about two standard errors on either side of 0, you can be about 95% confident that the unknown population parameter will be in the resulting interval. c. A standard error is essentially a standard deviation, specifically, the standard deviation of the sampling distribution of the estimate of the population parameter. d. All of these choices are correct characterizations of a typical standard error.
A carpenter is making doors that are 2058 millimeters tall. If the doors are too long they must be trimmed, and if they are too short they cannot be used. A sample of 13 doors is made, and it is found that they have a mean of 2043 millimeters with a variance of 1024. Is there evidence at the 0.025 level that the doors are too short and unusable? State the null and alternative hypotheses for the above scenario.
Let’s suppose that you have a set of time-series variables, and you want to model the relationship between them. Read the situations given below and answer the questions. (200 words)a) Explain the statistical test if the linear combination (of time-series variables) is I(0).b) Which statistical test can be applied if all the series are integrated of the same order I(1). Justify your answer
Since each process capability index relies on the estimate of process standard deviation, which in turns relies on sampling, therefore which following statement is INCORRECT? a. Confidence interval of each capability index should be found, instead of computing only a point estimate. b. Each process capability index follows some distribution. c. Each process capability index is a random variable. d. The distribution of Cpk is approximately normal. e. none of the above
Consider the double sampling plan for Spire CDs described in this section. Over aperiod of one year, 3,860 boxes of records are subject to inspection using this plan.If 60 percent of these batches are “good” (that is, in 60 percent of the batches theproportion of defectives is exactly 10 percent) and 40 percent are “bad” (that is, in40 percent of the batches the proportion of defectives is exactly 30 percent), thenwhat is the expected number of batchesa. Accepted?
Consider the double sampling plan for Spire CDs described in this section. Over aperiod of one year, 3,860 boxes of records are subject to inspection using this plan.If 60 percent of these batches are “good” (that is, in 60 percent of the batches theproportion of defectives is exactly 10 percent) and 40 percent are “bad” (that is, in40 percent of the batches the proportion of defectives is exactly 30 percent), thenwhat is the expected number of batchesd. Accepted on the second sample?
Consider the double sampling plan for Spire CDs described in this section. Over aperiod of one year, 3,860 boxes of records are subject to inspection using this plan.If 60 percent of these batches are “good” (that is, in 60 percent of the batches theproportion of defectives is exactly 10 percent) and 40 percent are “bad” (that is, in40 percent of the batches the proportion of defectives is exactly 30 percent), thenwhat is the expected number of batchesb. Rejected?
Consider the double sampling plan for Spire CDs described in this section. Over aperiod of one year, 3,860 boxes of records are subject to inspection using this plan.If 60 percent of these batches are “good” (that is, in 60 percent of the batches theproportion of defectives is exactly 10 percent) and 40 percent are “bad” (that is, in40 percent of the batches the proportion of defectives is exactly 30 percent), thenwhat is the expected number of batchese. Rejected on the first sample?
Consider the double sampling plan for Spire CDs described in this section. Over aperiod of one year, 3,860 boxes of records are subject to inspection using this plan.If 60 percent of these batches are “good” (that is, in 60 percent of the batches theproportion of defectives is exactly 10 percent) and 40 percent are “bad” (that is, in40 percent of the batches the proportion of defectives is exactly 30 percent), thenwhat is the expected number of batchesf. Rejected on the second sample?
Each of these columns of data represent a different soda bottling line, with the values representing the amount of soda per bottle in ounces. The business question being asked for each of the three comparisons is "do the two bottling lines bottle the same volume of soda on average, bearing in mind that the sample difference that you may observe could just be coincidence." What is the null hypotheses? Alternative hypothesis P value Alpha=0.05 Is it significant ? t-Test: Two-Sample Assuming Unequal Variances C7 C8 Mean 20.01679499870 20.59290905613 Variance 0.01032479977 0.01011215081 Observations 50.00000000000 50.00000000000 Hypothesized Mean Difference 0.00000000000 df 98.00000000000 t Stat 28.49610006164 P(T<=t) one-tail 0.00000000000 t Critical one-tail 1.66055121707 P(T<=t) two-tail 0.00000000000 t Critical two-tail 1.98446745451
The Empirical Rule tells us that … a) __________ of the data lies within 1 standard deviation of the mean b) __________ of the data lies within 2 standard deviation of the mean c) __________ of the data lies within 3 standard deviation of the mean