Consider the following RC circuit after the switch is closed. The resistances in the circuit have values R1= 6.0-2 and R2-6.0-2 and the capacitance is C=2.0 F. The combination is connected to power supply with ε = 12 V. After the circuit reaches steady state (after a very long time), what is the maximum energy stored in the capacitor? C R1 > dr W R2

Consider the following RC circuit after the switch is closed. The resistances in the circuit have values R1= 6.0-2 and R2-6.0-2 and the capacitance is C=2.0 F. The combination is connected to power supply with ε = 12 V. After the circuit reaches steady state (after a very long time), what is the maximum energy stored in the capacitor? C R1 > dr W R2

Principles of Physics: A Calculus-Based Text

5th Edition

ISBN:9781133104261

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter21: Current And Direct Current Circuits

Section: Chapter Questions

Problem 53P

See similar textbooks

Similar questions

Figure P29.60 shows a simple RC circuit with a 2.50-F capacitor, a 3.50-M resistor, a 9.00-V emf, and a switch. What are a. the charge on the capacitor, b. the current in the resistor, c. the rate at which the capacitor is storing energy, and d. the rate at which the battery is delivering energy exactly 7.50 s alter the switch is closed?
Consider a series RC circuit as in Figure P28.38 for which R = 1.00 M, C = 5.00 F, and = 30.0 V. Find (a) the time constant of the circuit and (b) the maximum charge on the capacitor after the switch is thrown closed. (c) Find the current in the resistor 10.0 s after the switch is closed.
The values of the components in a simple series RC circuit containing a switch (Fig. P21.53) are C = 1.00 F, R = 2.00 106 , and = 10.0 V. At the instant 10.0 s after the switch is closed, calculate (a) the charge on the capacitor, (b) the current in the resistor, (c) the rate at which energy is being stored in the capacitor, and (d) the rate at which energy is being delivered by the battery.
Consider a series RC circuit as in Figure P18.35 for which R = 1.00 M, C = 5.00 F, and = 30.0 V. Find (a) the time constant of the circuit and (b) the maximum charge on the capacitor after the switch is thrown closed. (c) Find the current in the resistor 10.0 s after the switch is closed. Figure P18.35 Problem 35 and 38.
(a) When the switch S in the circuit of Figure P28.14 is closed, will the equivalent resistance between points a and b increase or decrease? State your reasoning. (b) Assume the equivalent resistance drops by 50.0% when the switch is closed. Determine the value of R.
An ECG monitor must have an KC time constant lessthan 1.00102s to be able to measure variations involtage oversmall time intervals, (a) If the resistance of the circuit (duemostly to that of the patient's chest) is 1.00kTwhat is the maximum capacitance of the circuit?(b) Would It be difficult in practice to limit the capacitance to less than the value found in (a)?
The timing device in an automobile's intermittent wiper system is based on an RC rime constant and utilizes a 0.500F capacitor and a variable resistor. Over whatrange must R be made to vary to achieve time constants from 2.00 to 15.0 s?
In this chapter, most examples and problems involved direct current (DC). DC circuits have the current flowing in one direction, from positive to negative. When the current was changing, it was changed linearly from I=ImaxtoI=+Imax and the voltage changed linearly from V=Vmax to V=+Vmax where Vmax=ImaxR .Suppose a voltage source is placed in series with a resistor of R = 10 that supplied a current that alternated as a sine wave, for example, I(t)=(3.00A)sin(24.00st) . (a) What would a graph of the voltage drop across the resistor V(t) versus time look like? (b) What would a plot of V(t) versus I(t) for one period look like? (Hint: If you are not sure, try plotting V(t) versus I(t) using a spreadsheet.)
As in Example 27.2, consider a power supply with fixed emf and internal resistance r causing current in a load resistance R. In this problem, R is fixed and r is a variable. The efficiency is defined as the energy delivered to the load divided by the energy delivered by the emf. (a) When the internal resistance is adjusted for maximum power transfer, what is the efficiency? (b) What should be the internal resistance for maximum possible efficiency? (c) When the electric company sells energy to a customer, does it have a goal of high efficiency or of maximum power transfer? Explain. (d) When a student connects a loudspeaker to an amplifier, does she most want high efficiency or high power transfer? Explain.
Consider a circuit that consists of a real battery with an emf and an internal resistance of r connected to a variable resistor R. (a) In order for the terminal voltage of the battery to be equal to the emf of the battery, what should the resistance of the variable resistor be adjusted to? (b) In older to get the maximum current from the battery, what should the resistance variable resistor be adjusted to? (c) In order for the maximum power output of the battery to be reached, what should the resistance of the variable resistor be set to?
A capacitor with initial charge Q0 is connected across a resistor R at time t = 0. The separation between the plates of the capacitor changes as d = d0/(1 + t) for 0 t 1 s. Find an expression for the voltage drop across the capacitor as a function of time.
(a) What is the resistance of a light bulb that uses an average power of 75.0 W when connected to a 60.0-Hz power source having a maximum voltage of 170. V? (b) What is the resistance of a 100.-W lightbulb?