Consider the hydraulic lift shown in the figure. The small piston has an area ?1 of 0.0330 m2, and the large piston has an area ?2 of 4.00 m2. What force ?2 will the large piston provide if the small piston is pushed down with a force ?1 of 16.0 N? Assume that the fluid used in the lift is incompressible.

Consider the hydraulic lift shown in the figure. The small piston has an area ?1 of 0.0330 m2, and the large piston has an area ?2 of 4.00 m2. What force ?2 will the large piston provide if the small piston is pushed down with a force ?1 of 16.0 N? Assume that the fluid used in the lift is incompressible.

Physics for Scientists and Engineers, Technology Update (No access codes included)

9th Edition

ISBN:9781305116399

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter4: Motion In Two Dimensions

Section: Chapter Questions

Problem 4.8OQ: A girl, moving at 8 m/s on in-line skates, is overtaking a boy moving at 5 m/s as they both skate on...

See similar textbooks

Related questions

Q: Consider the hydraulic lift shown in the figure. The small piston has an area A¡ of 0.0330 m², and…

A: GivenArea of small piston(A1)=0.0330 m2Area of large piston (A2)=4.00 m2and Force (F1) on small…

Q: The small piston of a hydraulic lift (see figure below) has a cross-sectional area of 2.70 cm2, and…

Q: The small piston of a hydraulic lift has a cross-sectional area of 2.6 cm2 and its large piston has…

Q: The small piston of a hydraulic lift has a cross-sectional area of 3.9 cm2 and its large piston has…

Q: Hi please help: the large piston of a hydraulic lift has a cross-sectional area A1= 367 cm^2 and…

A: Write a given values of this question. A1=367cm2=367×10-4mA2=8.9cm2=8.9×10-4mW=64kN=64×103N

Q: The small piston of a hydraulic lift has a cross-sectional area of 4.7 cm² and the large piston has…

A: Given data: Cross-sectional area of Small piston (A1) = 4.7 cm2 Cross-sectional area of large…

Q: In a hydraulic lift system employing Pascal's law, what is the force required to lift up the larger…

Q: A hydraulic press for compacting powdered samples has a large cylinder with a diameter of 10.0 cm…

Q: The large piston of a hydraulic lift has a cross-sectional area of A1 = 501 cm and the small piston…

A: Given:Large Piston Cross section area,A1=501 cm2Small Piston Cross section area,A2=4.3 cm2 The small…

Q: The small piston of a hydraulic lift has a cross-sectional area of 2.4 cm2 and its large piston…

A: Given Data: Small piston area, As=2.4 cm2=2.4×10-4 m2 Large piston area, AL=321.3 cm2=321.3×10-4 m2…

Q: The large piston of a hydraulic lift had a cross-sectional area 60 times mc ross-sectional area.…

A: Suppose a hydraulic lift having a large & small cross-sectional area (A2) & (A1)…

Q: In a hydraulic press, the large piston has a cross-sectional area of 20 cm2. If F = 100 N is applied…

Q: A downward force of 100N is applied to the small piston with an area of 0.27 m^2 in the hydraulic…

A: Downward force (F1) = 100N Area of small piston (A1) = 0.27 m2 Large piston area (A2) = 3.14 m2 Let…

Q: What is the maximum weight F, that can be raised by the hydraulic lift shown in the figure, if area…

A: To solve the problem we will use Pascal's law which states that pressure on a confined fluid is…

Q: A hydraulic jack has an input piston of area 0.050 m2 and an output piston of area 0.70 m2 . How…

A: The expression for the input force is,

Q: Consider the hydraulic lift shown in the figure. The small piston has an area Aj of 0.0330 m², and…

A: A) As per Pascal’s principle, Here, P1 and P2 are the pressures at the pistons of area A1 and A2,…

Q: Two pistons of a hydraulic lift have a radius of 5 cm and 11.5 cm respectively. If the input force…

A: in the case of hydraulic lift , pressure at both piston is same that is P1 =P2 P1 = input pressure…

Q: HYDRAULIC LIFT. In the figure below, a hydraulic lift has one piston of diameter 8.0 cm and the…

Q: The small piston of a hydraulic lift has a cross-sectional area of 3.00 cm2, and its large piston…

A: Area of cross section of small piston, A1 = 3 cm2 Area of cross section of large piston, A2 = 200…

Q: The hydraulic lift's small piston with an area of 30 m^2 is subjected to a force of 100 N. To have…

Q: A hydraulic jack has an input piston of area 0.0600m2 and an output piston of area 0.690m2. How much…

A: Given : Input area , A1=0.0600 m2 Output area, A2=0.690 m2 force on the output Piston, F2=1.75 ×…

Q: A hydraulic press has one piston of diameter 2.0 cm and the other piston of diameter 8.0 cm. What…

A: According to Pascal law Pressure applied at one point of liquid equality transmitted throughout.

Q: A barber raises his customer’s chair by applying a force of 100N to a hydraulic piston of area 0.01…

A: Given data: Force on chair F1 = 100 N Area of hydraulic piston A1 = 0.01 m2 Area of new piston…

Q: A hydraulic jack has an input piston of area 0.0600 m2 and an output piston of area 0.660 m2. How…

A: according to pascal law pressure is same on input and output side FinputAinput=FoutputAoutput

Q: You wish to design a hydraulic lift such that it can lift a maximum load of 5000 kg. Your input…

A: given: F1min=50NF1max=100 NA1 = 1 mm2=1*10-6m2F2=5000kg*9.8 m/s2=49000 N we have to find A2max

Q: Area = 15 cm2 Area = 65 cm2 %3D %3D

A: Area of smaller side = 15 cm2area of larger side = 65 cm2mass of rock = 55 kg weight of rock = mg =…

Q: A car weighs 9800 N and sits on the hydraulic lift that utilizes a piston with a cross section area…

Q: A hydraulic jack has an input piston of area 0.0540 m2 and an output piston of area 0.710 m2. How…

A: Given data: Input piston area (A1) = 0.0540 m2 Output piston area (A2) = 0.710 m2 The force provides…

Q: 6. If a hydraulic pump had an input force from a piston of 10 N over an area of 10 square meters,…

Q: Consider the following hydraulic system. The car of mass 1000 kg is on the right hand side of the…

Q: The hydraulic lift's small piston with an area of 30 m^2 is subjected to a force of 100 N. To have…

Q: The area of the small piston in a hydraulic jack is 0.75 m². The area of the large piston is 3.0 m2.…

Q: A wooden block of mass 12 kg is floating in a pool. This is a fresh water pool, so we can assume a…

Q: The input piston and output plunger of a hydraulic car lift are at the same level, as shown in the…

Q: The smaller and larger pistons of a hydraulic press have radius of 3.5 cm and 13.5 cm. The input…

A: Given data: Radius of the smaller piston r1=3.5cm Radius of the larger piston r2=13.5cm Input force…

Q: What force (in N) must be exerted on the master cylinder of a hydraulic lift to support the weight…

A: Given data: Mass of a car is, m=2400 kg. Diameter of master cylinder is, d1=1.70 cm =0.017 m.…

Q: barber raises his customer's chair by applying a force of 150N to a hydraulic piston of area 0.01 m2…

Q: a hydraulic lift where a mass of 50 kg at the piston (point 1) balances a mass of 950 kg at point…

Q: Consider the hydraulic lift shown in the figure. The small piston has an area Aj of 0.0330 m², and…

A: Given: F1=18N, A1=0.033m2, y1=0.2m A2=4m2 Find: F2, y2, W1, W2…

Q: An automobile of mass 900 kg is supported by a hydraulic lift having a large piston of…

A: A hydraulic lift is based on Pascal’s law. Let the mass of the automobile be M, the cross sectional…

Q: In a hydraulic garage lift, the small piston has a radius of 5.0 cm and the large piston has a…

Q: For the hydraulic lift shown below, what must be the ratio of the diameter of the vessel at the car…

A: Given Data : The force applied at the small piston is given as F1 = 125 N. The mass of the car is…

Q: The small piston of a hydraulic lift has an area of 0.20 m^2. A car weighing 1.2 x 10^4 N sits on a…

A: Given: The small piston of a hydraulic lift has an area A1 = 0.20 m2 Weight of car, F2 = 1.2x104 N…

Q: A hydraulic jack has an Input piston of area 0.0540 m2 and an output piston of area 0.740 m2. How…

A: Given data: Input piston area (A1) = 0.0540 m2 Output piston area (A2) = 0.740 m2 Force on Output…

Q: A hydraulic lift has an input piston of area A and has an input force of 1000N. If the output piston…

A: Given- Force F1=1000NArea A1=AArea A2 =2A

Q: A hydraulic jack is used to lift objects such as automobiles. If the input force is 250 N over a…

A: Given data The input force is given as F1 = 250 N. The distance over the input force is applied is…

Q: The small piston of a hydraulic lift has a cross-sectional area of 3 cm, and its large piston has a…

A: Given data The cross-sectional area of the small piston is As = 3 cm2. The cross-sectional area of…

Q: In a hydraulic system, the radius of the large piston in a hydraulic Jack is 2.23 inches. The radius…

Q: A hydraulic jack has an input piston of area 0.0580 m2 and an output piston of area 0.710 m2. How…

Q: The hydraulic lift’s small piston with an area of 30 m^2 is subjected to a force of 100 N. To have…

A: Given data: Area of small piston (A1) = 30 m2 Input force (F1) = 100 N Output force (F2) = 7500 N…

Question

100%

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.

Recommended textbooks for you

Physics for Scientists and Engineers, Technology …

Physics

ISBN:

9781305116399

Author:

Raymond A. Serway, John W. Jewett

Publisher:

Cengage Learning