Consider the reaction: Calculate the rate of [NO3] production at 0.84 M [NO2]and 1.4 M [O3]. Final answer must be rounded off to 2 decimal places, and shall NOT have any units. The rate constant (M-1 s-1) for the reaction is ________. Final answer must be rounded off to 2 decimal places, and shall NOT have any units.

Consider the reaction: Calculate the rate of [NO3] production at 0.84 M [NO2]and 1.4 M [O3]. Final answer must be rounded off to 2 decimal places, and shall NOT have any units. The rate constant (M-1 s-1) for the reaction is ________. Final answer must be rounded off to 2 decimal places, and shall NOT have any units.

Fundamentals Of Analytical Chemistry

9th Edition

ISBN:9781285640686

Author:Skoog

Publisher:Skoog

Chapter7: Statistical Data Treatment And Evaluation

Section: Chapter Questions

Problem 7.17QAP

See similar textbooks

Similar questions

An analysis of city drinking water for total hardness was done by two students in the laboratory and produced the following results (in ppm CaCO3): Student A: 228.3, 226.4, 226.9, 227.1, and 228.6. Student B: 229.5, 226.1, 230.7, 223.8, and 227.5What is the 95% confidence interval for the mean?
Chemistry The levels of an organic pollutant (P) in the groundwater at the perimeter of a plant were a cause for concern. A 10 mL sample of the water was taken and the pollutant was extracted with 95% efficiency using 25 mL of diethyl ether. GC was used to analyse the concentration of P in diethyl ether. A calibration curve was plotted for a series of standards of P which yielded the following results: Peak Area Toluene Conc. (µg/ml) 12,000 2.6 23,700 5.0 35,500 7.7 46,800 9.9 31,250 Sample Determine the concentration of P in ppb in the initial groundwater sample.
1. Which of the following is NOT a true representation of the Lineweaver-Burk equation? Group of answer choices a. y-intercept = -1/Vmax b. x-intercept = -1/Km c. y = 1/V0 d. x = 1/[S] e. slope = Km/Vmax 2. If the y-intercept of a Lineweaver-Burk (double reciprocal) plot = 39.37 (sec/millimole) and the slope = 75.3 L/sec, Vmax equals: Group of answer choices a. 75.3 millimoles/sec. b. 0.0254 millimoles/sec. c. 0.523 millimoles/sec. d. 39.4 millimoles/sec. 3. Which of the following is true regarding allosteric enzyme behavior?Group of answer choices a. Allosteric enzymes are rarely important in the regulation of metabolic pathways. b. An allosteric effector binds reversibly on the surface of the enzyme. c. An hyperbolic representation of the relation initial velocity vs [S] is a specific characteristic of an allosteric enzyme behavior. d. Michaelis-Menten kinetics model the kinetic behavior of allosteric enzymes.
To test the quality of the work of a commercial laboratory, duplicate analyses of apurified benzoic acid (68.8% C, 4.953% H) sample were requested. It is assumed that therelative standard deviation of the method is sr →  = 4 ppt for carbon and 6 ppt forhydrogen. The means of the reported results are 68.5% C and 4.882% H. At the 95%confidence level, is there any indication of systematic error in either analysis?
Qq.1. Subject :- Account
You are trying to come up with a drug to inhibit the activity of an enzyme thought to have a role in liver disease. In the laboratory the enzyme was shown to have a Km of 1.0 x 10-6 M and Vmax of 0.1 micromoles/min.mg measured at room temperature. You developed a competitive inhibitor. In the presence of 5.0 x 10-5 M inhibitor, the apparent Km of the enzyme was found to be 1.5 x 10-5 M. What is the Ki of the inhibitor?
Chemistry (i) For T = 298K ΔG° = -8.314 x 298 x ln (2.83x10-3) = 14.524 KJ/mol (ii) For T = 308.15K ΔG° = -8.314 x 308.15 x ln (9.619x10-3) = 11.891 KJ/mol (iii) For T = 318.15K ΔG° = -8.314 x 318.15 x ln (3.14x10-2) = 9.147 KJ/mol (iv) For T = 328.15K ΔG° = -8.314 x 328.15 x ln (8.82x10-2) = 6.621 KJ/mol (v) For T = 338.15K ΔG° = -8.314 x 338.15 x ln (2.42x10-1) = 3.990 KJ/mol Based on the measured ΔG° values, is this equilibrium spontaneous at room temperature? Which factor, entropy, or enthalpy, has the greater impact on spontaneity in this case? Explain your answers.
4. Ksp=4.1x10-36 for Pb3(AsO4)2Calculate Eofor Pb3(AsO4)2(s) + 6e-  3Pb(s) + 2AsO43-Pb2+ +2e-  Pb(s) Eo= -0.126 V
Sample IdentificationCodeConcentration of M%TA=2-log(%T)Q50004.00 x 10-417.90.75Q50013.20 x 10-425.00.6Q50022.40 x 10-435.70.46Q50031.60 x 10-450.20.3Q50048.000 x 10-570.80.15SampleIdentificationCode%TA=2-log(%T)AMQ0210150143.70.359518560.360.000192Q0210150244.10.355561410.360.00018Q0210150343.80.358525890.360.00017Q0210150444.10.355561410.360.00018Q0210150543.80.358525890.360.00017What was their percent error?43%Does Batch 021015 meet legal requirements?No, because it is not between 2.85 * 10(4) and 3.15 * 10(4)Well #DropsBluedye1234567891012345678910Drops 9Distilled water876543210Concne 0.26tration0.52Test Tube #0.781.041.3Solutions3Concentration (M)2.082.32.6Concentration (ppm)1:1 dilution11.82Starting Dilution21.562:1 dilution0A.Zero standard0Was your calibration curve as linear as you expected?B.Did you experience any â€œdriftâ€ of the resistance readings?C.What is the equation of your best-fit line?D.What commercial drink did you analyze?E.Assuming…
Chemistry Calculate the mean, standard deviation, coefficient of variation given the following data Initial volume ( 0.00 + 0.05ml) Final volume ( 30.95 + 0.05ml) Discharged volume ( 30.95 + 0.05ml)
A standard method for analyzing aspirin tablets has a known variance of 20. A sample of 10 aspirin tablets is selected and analysed for the amount of aspirin using a modified method, yielding the following results: 254, 249, 252, 252, 249, 249, 250, 247, 251, 252. Determine whether the precision of the modified method is significantly different from that of the standard method at, alpha(a) = 0.10
Give two examples of the Scale Factor Error (one of the types of systematic error). Please do not give what is already given in the example. I need it ASAP Thank you