Answered: Consider the schematic of a riveted lap…

Consider the schematic of a riveted lap join subjected to tensile load F, as shown below. Le d be the diameter of the rivets, and S, be the maximum permissible tensile stress in the

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.2.17P: A hollow, circular, cast-iron pipe (Ec =12,000 ksi) supports a brass rod (Ec= 14,000 ksi} and weight...

See similar textbooks

Related questions

Q: Q1. A plate b mm wide and t mm thick is joined with another plate by a single transverse and a…

Q: A steel sleeve coupling (see the figure below) is designed to join 2 externally threaded members.…

A: Force, F = 30 kN yield stress of the material, Sy = 355 MPa The factor of safety, FS = 2

Q: 4. A single riveted lap joint is made thick plates with 20 mm diameter rivets. If the stress in…

A: Given data: τ=44.58 MPad=20 mm Need to determine the value of load P.

Q: 3. A tie bar is welded to a plate and it is subjected to axial load, P. The length of the fillet…

A: Given data Length of fillet weld (L) = 200 mm size of fillet (s) = 6 mm stress of the fillet weld…

Q: Q1: The weldment shown in the figure is subjected to a force F. The hot-rolled steel bar has a…

A: we have to calculate the maximum force so that failure does not happen.

Q: A welded connection, as shown in Fig. 2, is subjected to an eccentric force of 60 kN in the plane of…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: ASAP

Q: For two plates 1 and 2 a riveted system is suggested to connect them. W thickness of plate. 1 is 12…

Q: A bracket is riveted to a columm by 6 rivets of equal size as shown in Fig. 9.38. It carries a load…

A: Given Load = 100kN To find Diameter of the bolt

Q: Q2. A plate 120 mm wide and 8 mm thick is to be welded to another plate where the applied static…

Q: The lap joint is fastened with four 0.83-in.-diameter rivets. The working stress is 14.55 ksi for…

Q: A bracket in the form of a plate is fitted to a column by means of four rivets of the same size, as…

Q: A double riveted lap joint with chain riveting is to be made for joining two plates 10 mm thick. The…

A: Given Datat = 10mmσt = 60 mPaτ = 50 mPaσc = 80 mPaTo Find1) d2) P3) Pd4) n

Q: 1. The welded joint shown below is subjected to a 40 kN of static axial and a 40 kN of static…

Q: 2. Determine the shear, tensile and bearing stresses on a double riveted butt joint with ¾ in. main…

Q: Q1. A plate b mm wide and t mm thick is joined with another plate by a single transverse and a…

A: Parallel welds is weaker than transverse weld therefore, always assume any fillet weld like a…

Q: The one end of a hollow square bar whose side is 0.1 with 0.01 thickness is under a tensile stress…

A: Given Data:- Side(s) =0.1m = 3.93inch.......considering the unit as meters Thickness (t) =0.01m =…

Q: A 125 x 95 x 10 mm angle is welded to a frame by two 10 mm fillet welds, as shown in Fig. 1. A load…

A: Given data as per the question Load =16 KN Length of each weld =100 mm Calculations primary shear…

Q: 1. A 125 x 95 x 10 mm angle is welded to a frame by two 10 mm fillet welds, as shown in Fig. 1. A…

Q: Problem No. 2. A 150-mm-wide steel bar with a butt-welded joint, as shown. SET LOAD P NORMAL STRESS…

A: Given DataP=205kNσn=80MPaτ=40MPaθ=57{taken} C section taken for computing the minimum thickness

Q: A cast iron link, as shown in Fig. 4.4, is required to transmit a steady tensile load f 45 kN. Find…

Q: 3) What is the shear stress, fv, for the glue of the lap of the connection with P = 15,000 lb? What…

Q: Two welds, having length Li=150 L2=200 are required to attach a e to a column, as shown in Figure…

Q: A bracket, as shown in figure below, is welded to a plate. The welds have the same size, and the…

A: Given data as per question Force per mm applied =1 kN Total load =120 kN Calculations According to…

Q: Q1: Calculate the thickness of a triple riveted lap joint, if the rivet diameter of five plates is 5…

Q: A draw bar between a tractor and a trailer is made from a length of steel with a rectangular…

A: (i) Stess at secion X-Xσ=P(b-ϕn)A=1000 X 103(100-25) X 12σX-X=111.1MPawhere b and T→ width and the…

Q: The lap joint shown if Fig. is fastened by four 3/4 inch diameter rivets. Calculate the maximum safe…

Q: Assume that the axial load P = 40KN applied to the lap joint is distributed equally among the three…

Q: Q1. A plate b mm wide and t mm thick is joined with another plate by a single transverse and a…

Q: A bracket is riveted to a column by 6 rivets of equal size as shown in Fig. It carries a load of…

A: Given data as per question Applied load =100 KN No. of rivets =6 Stress in the rivet is limited =…

Q: B A bracket shown in the figure is designed to carry a dead weight of W = 15000 N. What sizes of…

Q: Write legibly, provide manual step by step solution, and diagram for below given problem.…

Q: A. for the lap joint shown below, calculate the safe axial tensile force P if Otensile=136MP ,…

Q: A 3/4-in. horizontal steel bar loaded at constant tension and welded to a vertical support is shown…

A: WELDING SYMBOL: It indicates the the complete welding for the joint design that is bevel weld symbol…

Q: 1-Two rivets holds three sheets of steel together, and is loaded as shown below. If the maximum…

Q: loading Fas shown in figure. Both legs of the fillets A fillet welded joint is subjected to…

Q: A steel bar of thickness h is welded to a vertical support as shown in the figure. Find the safe…

A: Given:b=60 mmc=160 mmd=60 mmh=5 mmζallow=140 MPaWe have to find safe force F if the maximum…

Q: The simplest truss consists of two rods and is loaded by a force. Given: F=13KN, angle a=44°. Cross…

A: Given:F=13 KNα=44°N=1.9σy=390 MPa

Q: A rectangular plate (0 =25°) is formed by welding two triangular a compressive stress of 2.5 MPa in…

A: Solution

Q: Figure shows a roof truss and the detail of the riveted connection at joint B. Using allowable…

Q: Find the smallest and safestd of the link as shown on the figure, if the working stress is equal to…

A: Find the smallest diameter

Q: Q1/ Calculate the forces in all rivets for the rivet group shown.

Q: the magnitude of the load?

A: Given; As shown in figure, A horizontal plate using four rivets , Load,P=500 NRivets diameter,d=50…

Q: In the figure, a single lap riveted joint is shown. The diameter of the rivets is d = 20 mm, plate…

Q: 3.) The diagram below shows a 5.5m long double angle brace which is connected by 6mm welding…

A: given data

Q: A horizontal plate has been joined to a vertical to a vertical post using four rivets arranged as…

Q: two plates are fastened by a number of rivets and a tensile load of 300 KN is applied, find the…

Q: The one end of a hollow square bar whose side is 10.42 in with 1.42 in thickness is under a tensile…

Q: 2. A bracket, as shown in Fig. 2, carries a load of 10 kN. Find the size of the weld if the…

Q: Find the smallest and safest d of the link as shown on the figure, if the working stress is equal to…

A: Given Working stress, SN = 20 MPa Force, FN = 10 kN Find Diameter, d

Concept explainers

Thermal Properties of Materials

In mechanical engineering, the thermal property is represented as the physical quantity that is relevant to the application of heat. The thermal properties are evaluated by variations in any specific material due to low heat or high heat. The quantities that influence the thermal property of the materials are mass, density, temperature, and many others.

Question

Determine the minimum value for the thickness of the plates

Consider the schematic of a riveted lap joint
subjected to tensile load F, as shown below. Let
d be the diameter of the rivets, and S, be the
maximum permissible tensile stress in the
plates. What should be the minimum value for
the thickness of the plates to guard against
tensile failure of the plates? Assume the plates
to be identical.
d
F
W
3D
W

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Types of Properties of Engineering Materials

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Consider the copper lubes joined in the strength of the copper is err = 200 MPa, figure using a "sweated" joint. Use the properties and what is the maximum load P]iwathat can be dimensions given. applied to the joint if the desired factor of safety in shear is FS_ - 2 and in tension is (a) Find the total elongation of segment 2-3-4 (
A hollow, circular, cast-iron pipe (Ec =12,000 ksi) supports a brass rod (Ec= 14,000 ksi} and weight W — 2 kips, as shown. The outside diameter of the pipe is dc= 6 in. (a) If the allowable compressive stress in the pipe is S00O psi and the allowable shortening of the pipe is 0.02 in., what is the minimum required wall thickness trmm? (Include the weights of the rod and steel cap in your calculations.) (b) What is the elongation of the brass rod Srdue to both load Wand its own weight? (c) What is the minimum required clearance h?
A two-story building has steel columns AB in the first floor and BC in the second floor, as shown in the figure. The roof load P:equals 400 KN, and the second-floor load P-, equals 720 kN. Each column has a length L = 3.75 m. The cross-sectional areas of the first- and second-floor columns are 11,000 mm" and 3900 mm", respectively. (a) Assuming that E = 206 GPa. determine the total shortenings aof the two columns due to the combined action of the loads Ptand P,. (b) How much additional load P0can be placed at t he top of t he column (point C) if t he total shortening: SACis not to exceed 4.0 mm?
A tubular post of outer diameter d2is guyed by two cables fitted with turnbuckles (see figure). The cables are lightened by rotating the turnbuckles, producing tension in the cables and compression in the post. Both cables are lightened to a tensile force of 110 kN. The angle between the cables and the ground is 60° and the allowable compressive stress in the post is ?? c= 35 MPa. If the wall thickness of the post is 15 mm, what is the minimum permissible value of the outer diameter d2?
A cylinder head of a steam engine is held on by 14bolts. The effective diameter of the cylinder is 35cm and the steam pressure is 85N/mm².Assuming that the bolts are not initially stressed; find the size of bolts if the tensile stress is not to exceed 20N/mm²
A cylinder head of a steam engine is held on by 14 bolts. The effective diameter of the cylinder is 35 cm and the steam pressure is 8.5 kg/cm2. Assuming that the bolts are not initially stressed, find the diameter of each of the bolts if the tensile stress is not to exceed 200 kg/cm2.
A Steel wire hangs vertically under its weight. What is the greatest length it can have if the allowable tensile stress o,-200 MPa Demity of steely 80 kN/m
A pressure vessel has an internal diameter of 1 m and is to be subjected to an internal pressure of 2.75 N/mm2 above the atmospheric pressure. Considering it as a thin cylinder and assuming the efficiency of its riveted joint to be 79%, calculate the plate thickness if the tensile stress in the material is not to exceed 88 MPa.
Design the spigot (in tension and compression) of the spigot and socket cotterjoint which is subjected to alternate tensile and compressive loading of 50 kN usingthe following data:Yield strength of cotter material SYS = 400 N/mm2, Factor of safety = 4 (for spigot)Assume thickness of cotter, t = 0.30d, where d is the diameter of the rod.
A steel railroad rails 10m long are laid with end-to-end clearance of 3mm at a temperature of 15C. (a) At what temperature will the rails just come in contact? (b) What stress would be induced in the rails at that temperature if there were no initial clearance? Use a=11.7x10^-6C and E=200GPa -Draw and label the diagram correctly, No diagram in the solution will be marked wrong. -Shortcut solution will be marked wrong.- Direction of the assumption of the equilibrium equation must be shown, no direction will be marked wrong. -Show complete solution and explanation for the answers
Q1. A plate b mm wide and t mm thick is joined with another plate by a single transverse and a double parallel fillet weld as shown in Fig. if the permissible tensile and shear stresses in the weld material are otw MPa and tw MPa respectively and the permissible tensile stress in the plate material are otp MPa, Find the length Li of single transverse fillet weld, if the joint is subjected to both static and fatigue loading. All dimensions in mm.
A steel bar of 5 mm is heated from 15° C to 40° C and it is free to expand. The bar Will induce A. no stress B. shear stress C. tensile stress D. compressive stress