Consider the stress state shown in Fig a) Find the "max shear stress" (t max) and the "average normal stress" (o avg). Indicate these points on the circle Mohr and show the summary on a square element b) Find the Cartesian constraints if the element is rotated 30degree Counterclockwise (CCW) and show the summary on a square element Note: for part (d) you can use the equations or the circle, it's your choice (using equations is faster)“ yt 40 MPа 30 MPa 20 MPa

Consider the stress state shown in Fig a) Find the "max shear stress" (t max) and the "average normal stress" (o avg). Indicate these points on the circle Mohr and show the summary on a square element b) Find the Cartesian constraints if the element is rotated 30degree Counterclockwise (CCW) and show the summary on a square element Note: for part (d) you can use the equations or the circle, it's your choice (using equations is faster)“ yt 40 MPа 30 MPa 20 MPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3.2: Find the angle & in the case of stress shown in the figure.
1)In the figure, the plane (biaxial) strainThe stress components for the state are given.a) Find the stress components σθ and τθ.b) Principal normal stresses-directions andFind the principal shear stresses (τmax, τmin).You can use these values on a directed element.show.c) Show the values of a and b on the Mohr Circle.
Represent the stress state on a 2-dimensional square element, given the Mohr circle below. (a) Determine the maximum shear stress. (b) Determine the maximum and minimum principal stresses. (c) Planes on which the greatest shear stress and principal stresses act are square other than the square element. Show the elements by drawing.
An element in uniaxial stress is subjected totensile stresses σx = 57 MPa, as shown in the figure.Using Mohr’s circle, determine the following.(a) The stresses acting on an element oriented at anangle θ =-33° from the x axis (minus meansclockwise).(b) The maximum shear stresses and associatednormal stresses.Show all results on sketches of properly orientedelements.
Determine the equivalent state of stress if an element is oriented 40° clockwise from the element shown. Use Mohr’s circle.
Solve for the equivalent force on an inclined surface. Look at Figure A.1 below. You will see a triangular block cut from a stress block with known stresses. The size and thickness of the block does not matter, so we will assume the area of the sloped inclined surface is A (sorry that it is the same symbol as the Point). If the area of the sloped surface is A, then the area of the other two surfaces is A cos (Theta) and A sin (Theta). First, draw a FBD of the block by multiplying each stress (normal and shear, known and unknown) by their associated area (in terms of A). Second, break the stress vectors on the side and bottom into components along the x’ and y’ axes. Third, sum the forces in the y’ direction and set them equal to zero (you should now be able to cross out the value of A for each term in your equation resulting in an equation with only one unknown, the normal stress in the y’ direction). Solve for the value of the normal stress in the y’ direction. Now repeat for…
Sigma x is 100MPa Sigma y is -60 Mpa Txy is -48 MPa Use Mohr circle to find normal and. Shear stress when it is rotated 25 as shown in figure
Calculate the characteristic dimension of the cross-section, b, and paste the section into the form, including dimensions in [cm]. Calculations of the cross-section characteristic dimension b, and other calculations should be attached to this solution. 2. According to the instructions in the form, do the calculations in units [kN] and [cm],e.g. moments of inertia in [cm4],stress in [kN/m2]. Recalculate stress into [MPa]. A. For the structure shown:1.Determine the number of static unknowns and number of equations of equilibrium. 2.Find the reactions at supports and at hinge connections, draw FBD with depicted calculated reactions for eachframe elements separated(F1).3.Determine the functions and draw the diagrams of shear force, axial force and bending moment along the frame elements (F2-F4).Check the balance of forces and moments exerted on the node B (F5, F6). Determine the most strained section (section at which the internal forces take its maximum values).B.For the cross-section…
Calculate the principal normal stresses and their directions, the maximum shear stresses, and the stresses that will occur on the inclined (C) surface of the stress element whose stress state is given in the figure, by drawing a figure using the MOHR CIRCLE METHOD. Show the stresses you find in the stress element. Show the findings on the Mohr circle and, where necessary, on the element. Place your accounts in the appropriate places.explain by writing (Note σx, σy, τ= τxy= τyx and σ values are given in Table 3 for each student). σx(kg/cm2) 3000 σy(kg/cm2) 500 τ(kg/cm2) 600 α (derece) 75
S1) The figure shows the stress distribution in the rectangular cross section of a beam.According to this;(a) Write the expression for stress ?x, taking into account the directions of Fx, My and Mz.(b) Show that My is zero for symmetrical normal stress distribution.(c) Using the stress function ?x, find the axial force Fx acting on the rectangular cross sectionin width b and height h.(d) Obtain the equation of Mz bending moment.Hint: In this question, using the stress distribution in the figure, it is aimed to determine thecross-sectional effects of Fx, My ve Mz causing this stress distribution
X=75MPa Y=90MPa S=40MPa D=-10 Note: If the angle D is positive, then the shear stress is in the direction shown on the unit element figure; if it is a minus sign, then the shear stress is in theopposite direction shown on the unit element figure.
Determine the equivalent state of stress if an element is oriented 50° counterclockwise to the element. Show the result on the element. Solve using Mohr's circle.