Please solve this Question 9Consider the structure shown in (Figure 1). Suppose that P = 4.5 kN and P = 5.5 kN.Part ADetermine the x-component of reaction at pin C.Express your answer to three significant figures and include the appropriate units.C2 =ValueUnitsSubmitRequest AnswerPart BDetermine the y-component of reaction at pin C.Express your answer to three significant figures and include the appropriate units.HACy =ValueUnitsFigure< 1 of 1 >SubmitRequest AnsweryP.P,Provide Feedback2 m-1.5 m---1.5 m--1.5 m--1.5 m-

Answered: Image /qna-images/answer/525481bc-5ad3-4648-a496-f06979da91bf.jpg

Consider the structure shown in (Figure 1). Suppose that P = 4.5 kN and P = 5.5 kN. Part A Determine the T-component of reaction at pin C. Express your answer to three significant figures and include the appropriate units. HẢ ? C, = Value Units Submit Request Answer Part B Determine the y-component of reaction at pin C. Express your answer to three significant figures and include the appropriate units. HẢ ? Cy = Value Units Figure < 1 of 1> Submit Request Answer y P P Provide Feedback B 2 m AL -1.5 m---1.5 m--1.5 m--1.5 m-|

Consider the structure shown in (Figure 1). Suppose that P = 4.5 kN and P = 5.5 kN. Part A Determine the T-component of reaction at pin C. Express your answer to three significant figures and include the appropriate units. HẢ ? C, = Value Units Submit Request Answer Part B Determine the y-component of reaction at pin C. Express your answer to three significant figures and include the appropriate units. HẢ ? Cy = Value Units Figure < 1 of 1> Submit Request Answer y P P Provide Feedback B 2 m AL -1.5 m---1.5 m--1.5 m--1.5 m-|

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

– The weight is suspended from structural A–36 steel alloy and 2014-T6 aluminum alloy wires, eachhaving the same initial length of 10 ft and cross-sectional area of 7×10–3 in2 (Figure Q1). If the weight is increasedgradually, determine which wire yields first? Explain which material model and yield criterion you will use? Justifyyour choices
Figure Q1 shows a composite rod ABC attached in between two rigid walls. Part AB is a solid rod made from Aluminium (E = 70 GPa), while part BC is a hollow cylindrical rod made from steel (E = 200 GPa).The diameter of part AB and the internal and external diameters of part BC are as shown in figure. A 40 kN force is applied at B in the direction as shown. If the compound rod is unstressed before theapplication of load,(a) determine the reaction at A and C.(b) determine the horizontal displacement of point B.
The rigid beam of negligible weight is supported by a pin at O and two vertical rods. Find the vertical displacement of the P=70kips weight. a. What is the elongation in bronze? b. What is the elongation in Steel? c. Vertical displacement of load P? -Draw and label the diagram correctly, No diagram in the solution will be marked wrong. -Shortcut solution will be marked wrong.- Direction of the assumption of the equilibrium equation must be shown, no direction will be marked wrong.
(a) Briefly explain why the Tresca yield criterion will result in a more conservative (safer) design than that based on von Mises criterion.(b) A cast alloy structure, ABCD is bolted at its base, A and carries a load of 235 N at end D, as shown in Figure Q1. The diameter of the structure is 20 mm. Take the yield strength of the alloy at 70 MPa:(i) Determine the stress acting in the material of the structure at point B. Draw the stress element and indicate the stress values.(ii) Determine if this stress state would cause yielding of the material by calculating the factor of safety using both the Tresca and von Mises yield criterion.(iii) Draw the loci of both yield criteria in the principal stress axes and indicate the stress state of part (ii) on the plot.
Determine the values of the reactions needed in the figure shown below
For the structure below indicate: a) What is the tension in cable BE? Consider P=792.1 kN.( Indicate the answer in kN.) b) What is the tension in cable CF. (Indicate the answer in kN.) c) What is the value of the reaction at D? (Indicate the answer in kN.)
Define the term Support Reactions?
6 cans containing soda made out of aluminum ( E = 69 GPa, σY = 240 MPa ) material are shaken. Shaking them creates an internal pressure of 0.14 MPa in each can. A uniform load of W is applied to the cans through a plate which has a negligible weight. The inner diameter of each can is 2R = 62 mm, the wall thickness is t = 0.25 mm and the length is L = 112 mm. According to the von - Mises yield criterion, determine the maximum magnitude of the applied load W. Note: The weight of the cans will be neglected in calculations. Accept that the liquid in the cans does not provide any support to the cans and no buckling occurs in the cans.
Determine the total elongation of the bar shown in figure below: -Draw and label the diagram correctly, No diagram in the solution will be marked wrong. -Shortcut solution will be marked wrong.- Direction of the assumption of the equilibrium equation must be shown, no direction will be marked wrong.
A 6061-T4 aluminum alloy is to be used to make a thin-walled cylindrical canister in which high-pressure chemical reactions will be performed. The design calls for a diameter of 50 cm, a length of 80 cm, and a maximum operating pressure of 5 MPa. Assume a safety factor of four is required (i.e., the maximum stress can never exceed onequarter of the alloy’s yield strength). a. What wall thickness is required to ensure safe operation? b. Is this wall thickness a maximum or a minimum? Explain. c. How do your answers change if the cylinder is made twice as long?
Passing an exploratory section through the body and exposing the internal forces acting on the exploratory section, Pxx produces elongation or contraction in members. T or F
H.W: An aluminum tube is rigidly fastened between a bronze rod and steel rod as shown in the following figure. Axial loads are applied at position indicated. Determine the stresé:in each material. Aluminum Bronze 1I5KN 15KN — f——— — 20 KN Ap=700mm? A, = 1000 mm? Steel A, =800 mm? oy 10KN