Consider the T-beam shown in (Figure 1). Suppose that a = 75 mm , b = 140 mm,c = 20 mm Part A Determine 7, which locates the centroidal axis z' for the cross-sectional area of the T-beam. Express your answer to three significant figures and include the appropriate units. y = 48.6 mm Submit Previous Answers Correct Part B Determine the moment of inertia Ir Express your answer to three significant figures and include the appropriate units. Figure < 1 of 1> ? I = Value Units Submit Previous Answers Request Answer X Incorrect; Try Again; 2 attempts remaining Part C

Consider the T-beam shown in (Figure 1). Suppose that a = 75 mm , b = 140 mm,c = 20 mm Part A Determine 7, which locates the centroidal axis z' for the cross-sectional area of the T-beam. Express your answer to three significant figures and include the appropriate units. y = 48.6 mm Submit Previous Answers Correct Part B Determine the moment of inertia Ir Express your answer to three significant figures and include the appropriate units. Figure < 1 of 1> ? I = Value Units Submit Previous Answers Request Answer X Incorrect; Try Again; 2 attempts remaining Part C

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Given beam loaded as shown below. Assuming EI is constant. 1. Which of the following gives the location of maximum deflection. a. 2.212 m b. 1.958 m c. 1.334 m d. 1.456 m 2. Which of the following the value of maximum deflection. a. 29.4/EI b. 17.5/EI c. 20.7/EI d. 14.2/EI
determine the deflection at E in mm using Double Integration Method Consider 150 mm x 150 mm section and E=200 GPa Enter the absolute value only and round off your answer to 3 decimal places PLS. ANSWER ASAP, I'LL RATE. THANKS
Determine the following unknowns on the beam shown below using Area-Moment Method. Consider 150 mm x 150 mm section and E = 80 GPa. Show complete and organized solution. Round-off your answers to two decimal places. a. Vertical Reaction at B in kN. b. Moment Reaction at A in kN-m. c. Deflection at point C in mm. d. Deflection at midspan of AB in mm.
For the beam loaded as shown in the figure 3, determine the deflection at midspan of the beam in mm using any Geometric Method. Consider 250 mm x 400 (b x h) mm section and E = 100,000 MPa. Enter the absolute value only and round-off your answer to 3 decimal places a = 5.5 m, b = 3.3 m, c = 20.3 kN/m, d = 27 kN.
20. Situation 22. For the built-up shape shown in the figure, determine: a. The location of plastic neutral axis form the top edge of the flange in mm. ____ b. The plastic section modulus about the horizontal axis. ______ x10^6 mm^3 (3 decimal places) c. The plastic moment with bending about the vertical axis if Fy = 345 MPa. _______kN-m (rounded to the nearest whole number)
Use THREE MOMENT EQUATION MET determine the member end moments of the beam of the rectangular cross section shown in Figure 11.10a. Assume that support B settles 2 cm. The modulus of elasticity and the moment of inertia of the beam are E = 210,000 N/mm2 and 4.8 × 104 mm,4 respectively. Hint final answer: MAB= 0 MBA= 165.5127 kn.m MBC= -165.5127 kn.m MCB= 52.2604 kn.m
determine the deflection at C in mm using Conjugate Beam Method. Consider 150 mm x 200 (b x h) mm section and E=80 GPa. Enter the absolute value only and round off your answer to 3 decimal places answer asap.
The flow rate of water flowing out of an 80mm diameter nozzle shown in Figure 1 is60 litre/s. The volume of the water in the pipe bend is 50 litres and the pipe bend isinstalled in a vertical plane. The head loss from point 1 to 2 is 0.44m. Calculate the xand y for components of the thrust block to hold the pipe bend.
The object W1 in the figure is at an angle of 45 to the horizontalIt is based on its frictionless surface at point B.Point A is articulated (fixed support) and ground frictionSince (μ = 0.3) body W2 is a surfaceWhat should be the weight of W1 that will cause it to start? W2= 38 [kN]sin45=cos45=0.7
Using DOUBLE INTEGRATION METHOD. Consider 150 mm x 150 mm section and E = 200 GPa. Enter the absolute value only and round-off your answer to 3 decimal places. GIVEN: a = 3.5m b = 16 kn/m c = 16 kn QUESTIONS: 1. Determine the REACTION at A in KN. 2. Determine the SLOPE at A in DEGREES. 3. Determine thw DEFLECTION at B in MM. 4. Determine the DEFLECTION at E in MM. THANK YOU!
Problem 2. Determine the following unknowns on the beam shown below using Area-Moment Method. Consider 150 mm x 150 mm section and E = 80 GPa. Show complete and organized solution. Round-off your answers to two decimal places. QUESTIONS: a. Vertical Reaction at B in kN. b. Moment Reaction at A in kN-m. c. Deflection at point C in mm. d. Deflection at midspan of AB in mm. GIVEN: a. 3.1 b. 18.0 c. 20
Determine the slope and vertical displacement of point A on the beam shown in the accompanying illustration. Use Conjugate Beam Method. E = 200,000 MPa