Consider the truss shown in (Ecure 1). Suppose that Fi-60 kN and F₂-25 kN Figure ▼ 40 kN Part C FGH 50AN Submit 15m 1 of 1 > 15m F 15m μÁ Value ∙F₁ Part A Request Answer Determine the force in member ED of the truss, and state if the member is in tension or compression Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. HA FD- Value Submit Request A Part B Determine the force in member EH of the truss, and state it the member is in tension or compression Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension Fen- Value Determine the force in member GH of the truss, and state if the member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. Submit Request Answer Pearson Units Units ESC ? Units

Consider the truss shown in (Ecure 1). Suppose that Fi-60 kN and F₂-25 kN Figure ▼ 40 kN Part C FGH 50AN Submit 15m 1 of 1 > 15m F 15m μÁ Value ∙F₁ Part A Request Answer Determine the force in member ED of the truss, and state if the member is in tension or compression Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. HA FD- Value Submit Request A Part B Determine the force in member EH of the truss, and state it the member is in tension or compression Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension Fen- Value Determine the force in member GH of the truss, and state if the member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. Submit Request Answer Pearson Units Units ESC ? Units

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Find the value of maximum load P sothat the stresses in the frame illustrated willnot exceed 120MN/m2 in tension or 90MN/m2in compression.The bars of the pin-connected frame shownhave a section of 35mmx65mm each.
Frame ACGE is on hinge support at Aand E and braced at B and F to resistforce T = 18kN.a = 2 mb = 1 mc = 1 ma. Find the reaction at D in kN. b. Find the stress in brace BD if it ismade of pipe of ø = 75 mm andthickness = 6 mm. c. If brace AB is connected to BDconsist of two flat bars bolted topost AC at B using 20-mm-ø bolt,find the average shear stress (inMPa) in the bolt.
34 - A support is a fixed, B support is a sliding joint. loads M= 30 kNm, P1= 12 kN, P2= 13 kN, q1= 6 kN ⁄ m, q2= 7 kN ⁄ m , spans are a= 2 m, b= 3 m. The support reactions in the beam whose loading condition is given in the figure will be found. Accordingly, Ax = ?A) 22.25B) 0C) None.D) 39.25E) 21/2
The horizontal platform ABCD has a 300 lb weight actingvertically through its center. The platform is held in equilibriumby hinges at A and B and by brace CE (brace DE has beenremoved). The hinge at A acts as a journal bearing and does notexert an axial force. Determine the reactions at the hinges andthe force exerted by the remaining brace CE Please provide an FBD and show all written work, thank you!
Assume that the axial load P = 40kN applied to the lap joint is distributed equallyamong the three rivets. What is the smallest diameterof the rivetif the allowable stresses are 90 MPa for bearing between a plate and a rivet, and 40MPa for shear in rivets?
Thumbs-Up will be given. Write the complette solutions legibly. Answer in 3 decimal places. Please answer all since they are all subquestions. Thanks Structural Theory 1d. Determine the vertical reaction R₂ in kN 1e. Determine the shear at midspan between vertical supports in kN. 1f. Determine the maximum factored load moment in the beam in kN.m
Two d mm*10 mm cover plates are welded to two UPN 200 channels 100 mm high to form the cross section of the compound beam shown in the figure. The moment of inertia of each channel about a horizontal axis through the centroid is 19.10*106 mm4. a) Determine the support reactions. b) Draw the shear force and bending moment diagrams. c) If the allowable bending stress of the beam is 300 MPa, find the required width d of the plates to safely support the load.
Find the max tension on member DI in kN. Put "0" if none. a= 4.5m b= 4.8m c= 50kN d= 68kN
A built-upsection is to be used as a girder. It is simply supported over a span of 9 meters and laterally supported at supports and midspan. Use Fy=345MPa and Cb=1.0 Properties of the section: A=12,620mm2 d=450 mm tw=10 mm bf=300mm tf=14mm rx=203.88mm ry=70.67 mm Ix=524.59x106mm4 a.Determine the elastic section modulus, Sx. b.Determine the plastic section modulus, Zx. c.Determine the compactness of the section. d.Determine the lateral support condition. e.Determine the Allowable Flexural Strength of the girder. f.Determine the Ultimate Flexural Strength of the girder.
16 -The stair beam in the figure will have support reactions. A support is a fixed, B support is a sliding joint. loads P1= 15 kN, P2= 30 kN, dimensions a = 2 m, b = 6 m, c = 4 m. Accordingly, Bx = ?A) 3.75B) None.C) 18.75D) 0E) 30
The steel truss supports a 6000-lb load. The cross-sectional areas of themembers are 0.5 in.2forABand 0.75 in.2forBC. Compute the horizontal displace-ment ofBusingE¼29106psi. ans. no. 10 only , GIVEN, REQD AND COMPLETE SOLUTION
A horizontal beam AD is supported by an inclined strut CB carries a load W = 2.4KN at the position shown. The strut which consists of one bar is connected to the beam by a bolt passing through the three bars meeting at joint C. BC is 75mm wide and 10mm thick strut while AD is 100mm wide by 10mm thick rigid bar. (a)What is the minimum required bolt diameter in at C if the allowable bolt shear is 68MPa? (b)Determine the stress in strut BC. (c)Determine the bolt stress at A if its diameter is 20mm.