The two blocks shown are originally at rest. Block A has a weight of 2501b and Block B has a weight of 4001b. Neglecting the masses of the pulleys and the effect of friction in the pulleys and between block A and the incline. a. Determine the acceleration of Block A in ft/s². b. Determine the acceleration of Block B in ft/s². c. Determine the tension force in of Block A in lb. d. Determine the tension force in of Block A in lb. 30⁰ B

The two blocks shown are originally at rest. Block A has a weight of 2501b and Block B has a weight of 4001b. Neglecting the masses of the pulleys and the effect of friction in the pulleys and between block A and the incline. a. Determine the acceleration of Block A in ft/s². b. Determine the acceleration of Block B in ft/s². c. Determine the tension force in of Block A in lb. d. Determine the tension force in of Block A in lb. 30⁰ B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A cylinder having a mass of 250 kg is to be supported by the cord that wraps over the pipe. Determine the largest vertical force F that can be applied to the cord without moving the cylinder. The cord passes (a) once over the pipe, β = 180°, and (b) two times over the pipe, β = 540°. Take μs = 0.2.
Determine the angle Φ at which the applied force P should act on the pipe so that the magnitude of P is as small as possible for pulling the pipe up the incline. What is the corresponding value of P? The pipe weighs W and the slope a is known. Express the answer in terms of the angle of kinetic friction, θ = tan-1 μk.
(a) Compute the horizontal displacement of joint B produced by the 240-kN load in Figure P8.10. For all bars, area = 2400 mm2 and E = 200 GPa. (b) Assuming that no load acts, determine the horizontal displacement of joint B if support A moves 20 mm to the right and 30 mm down and support E moves downward 36 mm.
1. How much work UP is done by the force P = 45 N on the collar?UP = _______N·m 2. How much work Ug is done by gravity on the collar?Answer: Ug = ______ N·m 3. Determine the speed of the collar as it passes position B.v =______ m/s
Determine the maximum horizontal force P that can be applied to the 30-lb hoop without causing it to rotate. The coefficient of static friction between the hoop and the surfaces A and B is μs = 0.2. Take r = 300 mm.
Use the dimension of the beam below to determine the I-moment of inertia Let P = 10 kips, L = 6 ft, a = 3 ft. E = 29 x 10^6 psi 1. Equation of the slope 2. Equation of the deflection curve 3. The deflection at the midpoint. 4. The slope at point B.
The block A and the wedge B weighs 100 kN and 40 kN, respectively. The coefficient of fritction for all contacting surfaces is µ = 0.268. Determine the following: a. What value of P in kN would be required to push to the right the wedge under the block? b. What value of P in kN would be required to pull to the left the wedge under the block? Assume the block A is stll in contact with the wall just as motion starts.
The blocks shown are separated by a solid strut which is attached to the blocks with frictionless pins. If the coefficient of friction for all surfaces is 0.25, determine the value of the horizontal force P to cause motion to impend to the right.
The continuous beam shown in the figure is fixed at both ends A and D, and supported by rollers at B and C Assume I = 800 x 106 mm4 and E = 70,000 MPa. W1 (kN/m) = 25 F (kN) = 50 S (mm) = 15 If there is a settlement of S at the support C, solve the following: 1. Slope at B, in radians 2. Slope at C, in radians 3. Reaction at A, RA in kN 4. Moment at A, MA in kN-m 5. Reaction at D, RD in kN 6. Moment at D, MD in kN-m
Determine the forces and moments at point C and point D. 66 Kn/m is the given
Block A supports a pipe column and rests as shown on wedge B. Knowing that the coefficient of static friction at all surfaces of contact is 0.25 and that θ = 45degrees, determine the smallest force P required to raise block A.
Circular beam with modulus of elasticity E=70 GPaA distributed load of 35 kN/m and a bending moment of k⨯2.3 kNm are applied. Using the analytical (integral) method;a) Determine the support reactions and the moment of inertia of the section.b) Moment function and 2nd order differential equation c) Boundary conditions, slope and deflection equationsd) the angle of inclination at point B (2),e) Determine the deflection (3) at point C.K=1.85 D (mm) L (m) k⨯87 k⨯1.5