Considering the previous circuit with parameter values of R = 10³, C = 2x10-6 F, and L = 2x10-³ H. The voltage v₁ is a step input of magnitude 5 V, and the voltage v2 is sinusoidal with frequency of 60 Hz and an amplitude of 4 V. The initial conditions are zero. Use Simulink to obtain a plot of the current response i3 (t). VI R 13 + V2

Considering the previous circuit with parameter values of R = 10³, C = 2x10-6 F, and L = 2x10-³ H. The voltage v₁ is a step input of magnitude 5 V, and the voltage v2 is sinusoidal with frequency of 60 Hz and an amplitude of 4 V. The initial conditions are zero. Use Simulink to obtain a plot of the current response i3 (t). VI R 13 + V2

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In a series RLC circuit shown in the figure, Vi(t) is the input voltage and the unit step function. VC(t) being the voltage falling at the capacitor ends;a) Write the equations of state.b) Using the values of R=2 Ohm, C=1F, L=1H, write the expression VC(s) using the expressions in which you found the equation of state.c) Obtain the VC(t) value for the VC(s) expression you found in option b using the residual sum method.
Q2. The step response at t > 0 of a series RLC circuit is observed to be vc(t) = 15 – 15 e -1000t cos1000t volts i,(t) = 45 e-100ot cos1000t + 45 e-1000t sin 1000t mA a) What are the values of R, L, and C? b) What is the circuit characteristic equation? c) What is the voltage across the resistor?
A series RC circuit with R = 40Ω and C = 0.1F is connected to a sinusoidal voltage v = 180sin(20t + β)V source at a time where β = 90°. The capacitor is initially uncharged. The s-domain equation for the current is given by the attached picture. Find the value of K1, K2, and K4.
Excecise 8.3 A DC source is connected to a series RLC circuit by a switch that closes at t=0 , as shown in the diagram below. (a) Write the differential equation for vC (t) . (b) Solve for v C (t) given that R=80Ω . (c) Repeat (b) R=40Ω and R=20Ω.
Ia = 2.5mA, Ib = 5mA, Vc = 18V, Vd = 15V. C1 = 12µF, C2 = 18µF, C3 = 10µF, C4 = 2µF. L1 = 12mH, L2 = 18mH, L3 = 10mH. R1 = 12kΩ, R2 = 20kΩ, R3 = 30kΩ, R4 = 8kΩ, R5 = 5kΩ, R6 = 12kΩ. The circuit is in dc steady state. Determine V2. Enter your answer in V rounded to two decimal places. If the sign is negative, please be sure to include the negative sign.
Ia = 2.5mA, Ib = 5mA, Vc = 18V, Vd = 15V. C1 = 12µF, C2 = 18µF, C3 = 10µF, C4 = 2µF. L1 = 12mH, L2 = 18mH, L3 = 10mH. R1 = 12kΩ, R2 = 20kΩ, R3 = 30kΩ, R4 = 8kΩ, R5 = 5kΩ, R6 = 12kΩ. The circuit is in dc steady state. Using superposition, consider only the effect of the source Vd. For this case, determine the total current generated by the source. Enter your answer in mA rounded to two decimal places. If the sign is negative, please be sure to include the negative sign.
A self-balancing robot is an inverted-pendulum example problem. The idea is to keep the robot upright by driving the wheels towards the leaning angle theta. When the robot is tilting forward, the wheels should be driven forward with a specific acceleration to counter the tilting. This will keep the robot in an upright position at all times. The block diagram of the system shown in Figure 3 with transfer function of G(s) = 1/s(s+1)(s2+4s+20) and H(s) = 1. a) Sketch the root locus by indicating the poles and zeros location on the loci. b) Locate the asymptotes on the root locus in (a). c) Determine the range of K to keep the system stable. d) Identify the jco axis crossing on the root locus in (a).
Find the stability condition of the equation given below. intervals of coefficients, what kind of conditions should they satisfy etc.) (Using Routh-Hurwitz criterion (according to the requirements and qualification conditions). a3.s 3+ a2.s 2+ a1.s+ a0=0
Use the following circuit drawings and reference designators to find (a) the Kirchoff's Voltage Loop (KVL) equations, (b) Kirchoff's Current nodal (KCL) equations, and (c) the associated second order characterisitic differential equation for i1 (use KVL), V0 (Use KCL)... make certain your differential equation is homogenous in terms of the single desired variable (i1(t) or V0(t)) as a function of time. The two circuit diagrams are attached.
Let i(0)=2 A. (a)In the s-domain, what is the Thevenin impedance seen by the 1-ohm resistor? (b) what is the Thevenin voltage seen by the 1-ohm resistor in the s-domain? (c) In the Thevenin equivalent circuit based on questions a & b, the expression for the current i(s) is in the form A/(Bs+C). If B=1, what is the value of C? (d)The expression for the voltage v(s) is in the form A/(Bs+C). If B=1, using i(s) and referring to the original circuit, what is the value of A?
1. Design a parallel RLC circuit using componentvalues from Appendix H, with a resonant radian frequency of5000 rad/s. Choose a resistor or create a resistor network so that theresponse is critically damped. Draw your circuit.2. Calculate the roots of the characteristic equation for the resistancein part (a).
1. Evaluate the following characteristic equations using both Hurwitz criterion a) s3 +2s2 +(4+K)+3s=0 b) s5 +10s4 +15s3 +30s2 +25s+10=0 2. Evaluate the following characteristic equation using Continued fraction criterion Q(s)=2s3 +8s+4+4s2 +8s−s3 +3+3s2