consolidated-drained triaxial test was conducted on an overconsolidated clay sample. he sample failed in test 1 at o1=200 kPa and o3=130 kPa, and in test 2 at 1=400 kPa and 3=290 kPa. Determine the undrained and drained friction angles and cohesion for the

consolidated-drained triaxial test was conducted on an overconsolidated clay sample. he sample failed in test 1 at o1=200 kPa and o3=130 kPa, and in test 2 at 1=400 kPa and 3=290 kPa. Determine the undrained and drained friction angles and cohesion for the

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter12: Shear Strength Of Soil

Section: Chapter Questions

Problem 12.20P

See similar textbooks

Similar questions

The results of two consolidated drained test tri axial tests on a clay are given below specimen 1: chamber pressure = 105 deviator stress = 220 specimen 2: chamber pressure = 210 deviator stress = 400 1. determine the angle of internal friction 2. determine the cohesion of clay 3. determine the normal stress on the point on the failure plane of the 2nd specimen
A drained triaxial test was conducted on a normally consolidated clay specimen with a chamber confining pressure of 145 kN/m2. At failure, the deviator stress was 198 kN/m2. Determine the soil friction angle.
Experimental data for clay specimen obtained initial values of e1 = 1.12 and P1 = 90 kPa, and final values of e2 = 0.90 and P2 = 460 kPa Solve for the compression index
17. The results of a consolidated drained test for a normally consolidated clay were as follows: chamber confining pressure = 300 Kpa and deviator stress = 400 KPa a. Compute the angle of friction of the clay sample b. Compute the shear stress at failure plane c. Compute the normal stress on the plane of maximum shear.
A consolidated-undrained triaxial compression test was performed on a normalconsolidated clay sample. During the experiment, the confining pressure was 140 kPa, thedeviator stress was 125 kPa, and the pore water pressure was 75 kPa at the time of failure.According to the information given:i- Find the consolidated-undrained internal friction angle of the clay. ii- Find the drained friction angle of the clay
A drained triaxial test on a normally consolidated clay showed that the failure plane makes an angle of 58° with the horizontal. If the sample was tested with a chamber confining pressure of 103.5 kN/m^2, what was the major principal stress at failure?
A Consolidated-Drained Triaxial Test was conducted on a normally consolidated clay. The results were as follows:· Chamber confining pressure = 400 kPa· Deviator Stress = 600 kPaa. Compute the angle of friction of the clay sample b. Compute the shear stress on the failure plane
The figure below shows a 24 m thick layer of normally consolidated clay (ϒt = 18.6 kN/m3) that is one-dimensionally loaded by Δσv = 100 kPa. The clay layer is below a 4 m thick layer of granular fill (ϒt = 19.6 kN/m3), and a dense, compacted glacial till underlies the clay. The water table is located at the top of the clay layer. A 1-D consolidation test is performed on a 2.50 cm thick, doubly drained specimen from the middle of the clay layer. When the stress conditions from the field (including Δσv = 100 kPa) are applied to this specimen, it takes 6 min for 90% average consolidation to occur.a. From the lab test data, determine cv for the soil.b. Compute the pore pressure at depth 22 m before and immediately after the 100 kPa stress is applied.c. At depth 22 m, compute the pore pressure 8.5 years after the 100 kPa is applied.
The figure below shows a 20 m thick layer of normally consolidated clay (ϒt = 18.6 kN/m3) that is one-dimensionally loaded by Δσv = 60 kPa. The clay layer is below a 5 m thick layer of granular fill (ϒt = 19.6 kN/m3), and a dense, compacted glacial till underlies the clay. The water table is located at the top of the clay layer. A 1-D consolidation test is performed on a 3.00 cm thick, doubly drained specimen from the middle of the clay layer. When the stress conditions from the field (including the Δσv = 60 kPa) are applied to this specimen, it takes 1.5 minutes for 60% average consolidation to occur.a. From the lab test data, determine cv for the soil.b. Compute pore water pressure at 20 m depth 7 years after the Δσv is applied to the clay layer. c. Compute the average degree of consolidation 7 years after Δσv application.
A clay sample was consolidated in a triaxial cell under a backpressure of 50 kPa and cell pressure of 150 kPa. The drainage valve was then closed and the cell pressure was increased to 200 kPa when the pore pressure increased to 98 kPa. What is Skempton’s B-parameter? The above sample was then subjected to a vertical deviator stress, which was increased from zero under undrained conditions. The sample failed when the pore water pressure was 160 kPa and the deviator stress was 70 kPa. What is Skempton’s A-parameter at failure? Assuming the clay is normally consolidated, find the friction angle in terms of effective stresses.
The following results were obtained at failure in a series of drained triaxial tests on fully saturated clay specimens originally 38 mm diameter by 76 mm long. All-round pressure (kN/m2) Axial compression (mm) Axial load (N) Pore-water pressure (kN/m2) 200 400 600 7.22 8.36 9.41 480 895 1300 25 75 100 (a) Determine the values of the shear strength parameters c and . (b) Determine the values of the shear strength parameters c and . (c) A different specimen of the same soil is tested in undrained triaxial compression at a cell pressure of 240 kN/m2 and fails when the deviator stress is 160 kN/m2. Calculate the pore water pressure in the specimen at failure.
In a triaxial test, a specimen of saturated [normally consolidated] clay was consolidated under a chamber confining pressure of 80 kPa. The axial stress on the specimen was then increased through the allowing the drainage from the specimen. The specimen fails when 120 kPa. The pore water pressure at the time was 50 kPa. What is the consolidated undrained friction angle [phi]?