Convection. A thin 100 cm long and 10 cm wide horizontal plate is placed in a large tank full of water at 60°C. At what uniform temperature, in °C, should be maintained in the plate if the rate of heat supplied to the plate is 2 kW as heat is dissipated from either side? The convection heat transfer coefficient at the lower side is h, = 384.5 W/m²K and h,= 3215.5 W/m²K at the upper side. %3D

Convection. A thin 100 cm long and 10 cm wide horizontal plate is placed in a large tank full of water at 60°C. At what uniform temperature, in °C, should be maintained in the plate if the rate of heat supplied to the plate is 2 kW as heat is dissipated from either side? The convection heat transfer coefficient at the lower side is h, = 384.5 W/m²K and h,= 3215.5 W/m²K at the upper side. %3D

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter2: Steady Heat Conduction

Section: Chapter Questions

Problem 2.38P: 2.38 The addition of aluminum fins has been suggested to increase the rate of heat dissipation from...

See similar textbooks

Similar questions

3.16 A large, 2.54-cm.-thick copper plate is placed between two air streams. The heat transfer coefficient on one side is and on the other side is . If the temperature of both streams is suddenly changed from 38°C to 93°C, determine how long it takes for the copper plate to reach a temperature of 82°C.
An electrical transmission line of 1.2-cm diameter carries a current of 200 amps and has a resistance of 310-4 ohm per meter of length. If the air around this line is at v, determine the surface temperature on a windy day, assuming a wind blows across the line at 33 km/h.
1.19 A cryogenic fluid is stored in a 0.3-m-diameter spherical container is still air. If the convection heat transfer coefficient between the outer surface of the container and the air is 6.8 , the temperature of the air is 27°C, and the temperature of the surface of the sphere is –183°C, determine the rate of heat transfer by convection.
Heat is transferred at a rate of 0.1 kW through glass wool insulation (density=100kg/m3) with a 5-cm thickness and 2-m2 area. If the hot surface is at 70C, determine the temperature of the cooler surface.
The air-conditioning system in a Chevrolet van for use in desert climates is to be sized. The system is to maintain an interior temperature of 20C when the van travels at 100 km/h through dry air at 30C at night. If the top of the van is idealized as a flat plate 6 m long and 2 m wide and the sides as flat plates 3 m tall and 6 m long, estimate the rate at which heat must be removed from the interior to maintain the specified
2.38 The addition of aluminum fins has been suggested to increase the rate of heat dissipation from one side of an electronic device 1 m wide and 1 m tall. The fins are to be rectangular in cross section, 2.5 cm long and 0.25 cm thick, as shown in the figure. There are to be 100 fins per meter. The convection heat transfer coefficient, both for the wall and the fins, is estimated to be K. With this information determine the percent increase in the rate of heat transfer of the finned wall compared to the bare wall.
Determine the rate of heat loss from the wall of a building resulting from a 16 km/h wind blowing parallel to its surface. The wall is 24 m long and 6 m high, its surface temperature is 27C, and the temperature of the ambient air is 4C.
A person puts a few apples into the freezer at 15°C cool them quickly for guestswho are about to arrive. Initially, the apples are at a uniform temperature of 20°C,and the heat transfer coefficient on the surfaces is 8 W/m2·K. Treating the apples as9-cm-diameter spheres and taking their properties to be 840 kg/m3, Cp 3.81 kJ/kg·K, k = 0.418 W/m·K, and α =10-7 m2/s, determine the center and surface temperatures of the apples in 1 h. Also, determine the amount of heat transfer from each apple. Solve this problem using analytical one-term approximation method (notthe Heisler charts). Answer: Center: 11.2 ℃, Surface: 2.7 ℃, heat transfer: 17.2 kJ
A heating system is to be designed to keep the wings of an aircraft cruising at a velocity of 900 km/h above freezing temperatures during flight at 12,200-m altitude where the standard atmospheric conditions are 55.4°C and 18.8 kPa. Approximating the wing as a cylinder the elliptical cross section whose minor axis is 30 cm and disregarding radiation, determine the average convection heat transfer coefficient on the wing surface and the average rate of heat transfer per unit surface area.
Four power transistors, each dissipating 12 W, are mounted on a thin vertical aluminum plate 22 cm * 22 cm in size. The heat generated by the transistors is to be dissipated by both surfaces of the plate to the surrounding air at 25°C, which is blown over the plate by a fan. The entire plate can be assumed to be nearly isothermal, and the exposed surface area of the transistor can be taken to be equal to its base area. If the average convection heat transfer coefficient is 25 W/m2·K, determine the temperature of the aluminum plate. Disregard any radiation effects.
Consider a 1.2-m-high and 2-m-wide glass windowwith a thickness of 6 mm, thermal conductivity k = 0.78W/m·K, and emissivity « = 0.9. The room and the wallsthat face the window are maintained at 25°C, and the averagetemperature of the inner surface of the window is measuredto be 5°C. If the temperature of the outdoors is 25°C,determine (a) the convection heat transfer coefficient on theinner surface of the window, (b) the rate of total heat transferthrough the window, and (c) the combined natural convectionand radiation heat transfer coefficient on the outer surface ofthe window. Is it reasonable to neglect the thermal resistanceof the glass in this case?
A 6 cm diameter sphere is initially at a temperature of 100C. Later, this sphere was thrown into water at 800C. Calculate how long it will take for the center temperature of the sphere to reach 500C by taking the convection heat transfer coefficient as 80W / m2K. Thermal properties of sphere material: k=0,627 W/moC a=0,151x10-6 m2/s