Conveyor warning signal program: A warning alarm rings for a duration of 10 seconds before a conveyor motor runs in a factory. Implement the ladder diagram program to turn on the alarm immediately when a push button is pressed. Once the alarm stops, the conveyor motor should automatically starts running. Provide a push button to reset the operation. Use TON in your solution.

Q: State the correct terminology used to describe each of the following 1.the current drawn by a motor…

A: For the following statements, we need to provide terminology of the given statement.

Q: In the simple lamp dimmer shown here, what method of power control is being used? LAmP AC supply…

A: The figure shows a lamp dimmer circuit, this circuit uses the DIAC and TRIAC combination for the…

Q: A single-phase electric motor is connected to a 240-volt, 30-ampere circuit. The motor nameplate…

A:

Q: 5. A thermostat of an air conditioner working in cool mode was working on a 3°C differential. If it…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: How does a lightning rod system work ?

A: LIGHTNING ROD:- Lightning rod is basically a metallic rod  that is used to protects a structure from…

Q: Consider a system with four pushbuttons and three lamps and three motors. PB 1 is used for main…

A: Solution- Given, Consider a system with four pushbuttons and three lamps and three motors. 1. PB 1…

Q: QUESTION 1 How does a N/O relay operate contacts are closed when the coil is de-energized and open…

A: Relay terminals Coils ( 2 nos) NC NO Common

Q: 8.a. What is the purpose of relay CRE in the roll stand machine? A. Relay CRE is used as an…

A: CRE relay is used to detect fault in the input circuit. It is used in stop button of contact welding…

Q: Three - wire control prevent the restarting of machinery when power is restored.

A:

Q: Rotor of the electrical machine, having 8 poles, is turned on 360 electrical degrees. How much is…

A: The mechanical degree corresponding to the electrical degree of the electrical machine needs to be…

Q: 9. When you're taking a PM motor apart you should exercise special care not to damage the A. brush…

A: The solution is given below.  The brush holder is taken into special car during operation of PM.

Q: At standstill condition, the back emf is zero, so the motor can be safely turned ON without a…

A:

Q: A closed-loop temperature control system has the ability to automatically maintain the temperature…

A: True

Q: For the Starting Up the Power Station Simulator Why are certain operations blocked by isolators

A:

Q: Input Timer True Figure 2 False Rung condition- Timed period- Timed duration 7. For Figure 2; The…

A: Since you have posted a question with multiple sub-parts, we will solve first Three subparts for…

Q: As a service engineer, you are troubleshooting at an electropneumatic system. You filled the…

A: PLC- Programmable Logic controller. It is an controller which works on the basis of implemented…

Q: Explain all part and its working in motion control lamp diagram

A: One can use motion sensors to automatically turn on a light when someone approaches in home. In this…

Q: At standstill condition, the back emf is zero, so the motor can be safely turned ON without a…

A: Choose the correct option At standstill condition, the back emf is zero, so the motor can be safely…

Q: Q3/ Chose the correct answer for the following 1. Synchronous motors are generally not self-starting…

A: In this question we will write about synchronous motor related answers... Note :- as per our…

Q: STUDENT DRILL PROBLEMS: Draw the basic building blocks of the following systems. Explain briefly the…

A: The Building block diagram is the summary representation of any system in which the energy flow and…

Q: 9- Controlled variable is the output of  a. Plant b. Controller c. None of the above d. Error…

A:

Q: 1. It is a machine that converts mechanical energy to electrical energy. 2. It is a machine that…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: What is the function of an arc chute

A: function of an arc chute

Q: Which one of the following is the application of DC machine? O a. Pumps O b. Oven O c. Cranes O d.…

A: DC motors are divided into three types 1 Series motor, 2 Shunt motor, and 3 Compound motor. The…

Q: Make a circuit to control the 3-phase AC motor, such that it will turn on when the on button (NO) is…

A: Make a circuit to control the 3-phase AC motor, such that it will turn on when the on button (NO) is…

Q: In the motor control circuit of Figure 11 in your study unit, the operation of any one of the…

A: Asked to choose correct option from given circuit.

Q: O a. The amount of energy transferred is dependent on the rotor size and the wind speed. O b. The…

A:

Q: During the baked bean production in oven process, it should fulfill the following requirements 1)…

A: PB1 (NO) starts the conveyor motor M1 when pressed. This action starts the timer T1 (TON - Timer On…

Q: Identify the count cycle and timing diagram of counters

A: A Counter is a device in digital logic and computing that saves (and occasionally shows) the number…

Q: . A maintained push button will A. hold its position after it is pressed and released. B. open after…

A:

Q: quieston 2: Assume all timers are set for 3 seconds. When the start button is pressed, motor #1…

A: Timers set to 3 second set time Each motor operate after 3 second except motor 1 To select correct…

Q: What is the first module in the rack after the power supply? O DC Input Card O DC Output Card O…

A: This question is related to Programmable Logic Controller (PLC). The foundation of PLC is the rack…

Q: Overloading a single-phase motor will result in: Select one: O a. overheating the motor O b. no…

A: Overload in a motor can be caused due to following reasons: a) Increase in load b) Low input voltage…

Q: In your opinion and own understanding as a student, why is that timer switches are important to the…

A: The digital circuits can be sequential or combinational circuits. The combinational circuits depend…

Q: What is the mechanism of operation motion control lamp

A: mechanism of operation motion control lamp:

Q: True or False

A:

Q: How can you safeguard your machine against sudden voltage changes?

A:

Q: What is the purpose of the magnetic contactor?

A: Magnetic contactor:- It is an electrically controlled magnetic switch It is used upto 1000 volts

Q: H.W: What instruction would you select for each of the following discrete input field devices to…

A: Devices that receive discrete digital signals—also known as digital input devices—can only transmit…