Cooling load calculation of a single family house using CLTD/GLF method

Q: For the given figure below, determine the force that would cause the bar to deform by 1.8x10^-2 inch...

A:

Q: Water in a rectangular, finished-concrete channel, n = 0.017 overflows a dam, as shown in the figure...

A: An open channel is a deep hollow surface with the top surface normally exposed to the environment. T...

Q: A cantilever beam 80 mm wide by 260 mm high and 9 m long carries a lpad that varies uniformly from z...

A: First find moment at 4m from free end . Use bending equation.

Q: Ship A left a Port at 12:00 noon and sails N 42°18' E at a rate of 3 mph. At 2:00 PM, ship B starts ...

A:

Q: 7-Both pulleys are fixed to the shaft and as the shaft turns with constant angular velocity, the pow...

A: Free body diagram can be drawn as

Q: A cube has a volume of 27,000 cm3. The cube is cut by a plane containing two diagonally opposite edg...

A:

Q: The cantilever beam carries a combination of a uniformly distributed load and a trapezoidal loading ...

A:

Q: ar and moment coordinate, then draw the diagram.

A:

Q: A high-strength steel band saw, 22 mm wide, runs over pulleys 700 mm in diameter. What minimum thick...

A:

Q: 6. If the cord at B suddenly fails, determine the horizontal and vertical components of the initial ...

A: free body diagram can be drawn as  

Q: Determine the design compressive strength (kips) of a A36 steel column, W 10 X 33 with a total lengt...

A:

Q: In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to in...

A:

Q: What is the shearing stress developed at the neutral axis of the beam with a circular cross section ...

A:

Q: Lantilever nethod F Solve for all the Sup port reactins. In dicote units & directions as well. JookN...

A:

Q: Determine the force in each members.  MN=104 SN=66

A: To find force in all members of the truss

Q: Water at 7 ft/s and 65 F flows in a 10 in schedule 40 pipe (inside diameter  from Table A.III.1(SI) ...

A: The given data is shown below: Velocity=7 ft/sDiameter=10.02 in.

Q: The length of rod AB is 10 m and it is supported at midspan by link CD. The length of line AC is 4 m...

A:

Q: f the motion of a jet after landing on a runway is shown by the a-t graph below. Note that att = 0 s...

A:

Q: For the state of str maximum in-plane results on a sketch with the planes of r stress. Using Analyt

A:

Q: 2. Determine the force in members LK, KC, and CD of the Pratt truss. State if the members are in ten...

A:   The answer is found to be Force in members 1. LK=62.22 KN  compression 2. KC=6.67 KN compression 3...

Q: 1- In civil construction, the use of T profiles for pillars is very common and also considers the in...

A: Centre of gravity gives the position through which the force of gravity acts.

Q: Refer from the figure shown below: a.) What force F must be applied to the following static componen...

A:

Q: Can someone explain where the 32.2 is coming from please

A: Question: where the 32.2 is coming 

Q: 1 kip 4 kips kip BY В C A 6.4 ft Do E F 2.4 kips -12 ft- -12 ft-

A: This is a symmetrical frame section. Point D is roller support while F is hinged support. This frame...

Q: Determine the force in each member of the space truss and state if the members are in tension or com...

A: Joint method: The joint method is a technique for computing unknown forces acting on truss component...

Q: A flat steel bar, 27 mm wide by 2 mm thick and 1.6 m long, is bent by couples applied at the ends so...

A:

Q: The "total" shear strength parameters of a soil are given as: Cohesion, c = 50 kPa; Angle of interna...

A:

Q: The lab apparatus shown in the figure maintains a constant head in both the upper and lower reservoi...

A:

Q: Explain how the designated port (DP) is selected in Spanning Tree Protocol.

A:

Q: Solve the absolute maximum shear force in the beam. 16 k 2 k/ft 8k 3 k/ft A B. E F 12 ft8 ft- 9 ft--...

A:

Q: The azimuth of a line is 207*. The back azimuth of the same line is A. 63* B. 297* C. 27* D. 117...

A: Azimuth is Angular measurement in a spherical coordinate system. Back Azimuth is calculated by addin...

Q: From the figure shown below, if the diameter of the steel and concrete is 6.5 in and 6 in respective...

A:

Q: eter of material 2, so that there is no conta material 2? eP= 385 kN eter of Material 1 85 mm son's ...

A:

Q: Determine the force in each members.    MN=104 SN=66

A: To find force in all members of the truss

Q: A wood with a dimension 53 mm and 131 mm with 131 mm is side positioned vertically is subjected to A...

A: Given that,  dimension of wood = bxd = 53mm x 131mm Length of the sample, L = 51 cm = 510 mm Modulus...

Q: "Determine the minimum width "b" of the beam shown if the flexural stress is not to exceed 13 MPa. A...

A:

Q: Solve via shear and moment ordinates then draw the diagram

A:

Q: t can be applied to the shaft if it has a outer diam of 5 mm? (answer in N-m)

A:

Q: Problem No. 1 A copper rod of length L =18.0 in. is to be twisted by torques T (see figure) until th...

A:

Q: Two tension ropes are connected to a wall and subject to forces as shown by the diagram below. Deter...

A:

Q: For the overhanging beam shown, calculate the deflection of the elastic curve midway between the su ...

A:

Q: Two circles have radii 3 inches and 8 inches. The distance between their centers is 18 inches. How l...

A:

Q: Four equal wheel loads of 30 kN each, separated by 1 m between each load, roll as a unit across a 14...

A:

Q: Enumerate all the necessary factors that you think are needed to be consider in selecting proper mat...

A: The necessary factors that are needed to be consider in selecting proper materials in engineering de...

Q: A 31 mm radius Steel is subjected to tensile test. Determine its yield and ultimate load it can carr...

A: Given that, radius = 31 mm steel grade = 60 and 40 modulus of elasticity, E = 231 GPa length = 31 m ...

Q: Determine the force in each member.  MN=104 SN=66

A: To find force in all members of the truss

Q: As shown in the figure, a rigid beam with a negligible mass is pinned at one end and supported by tw...

A: Given data in question  Area  Length Elasticity modulus  Load  Dimensions  To find out  Elongation i...

Q: A certain beam in its upright position is estimated to have a vertical bending moment Mux - 218 kN-m...

A: Given data : Mux=218 kN-mMuy=48 kN-mSx=2524×103 mm3Sy=251×103 mm3Zx=2901×103 mm3Zy=401×103 mm3Fy=248...

Q: The maximum tension in the steel rod is 580 N and the maximum stress in che link is 30 N/mm2. IT esi...

A:

Q: A closed tank 2.4 m long , 1.2 m wide and 1.4 m high contains water 1.1 m deep. A small hole is loc...

A: Length of tank (l) = 2.4m Width of tank (b) = 1.2m Height of the tank (h) = 1.4m Height up to which ...