For the given figure below, determine the force that would cause the bar to deform by 1.8x10^-2 inches. Other properties: x-sectional area: 0.25 in^2. E-steel = 29x10^6 lbs/in^2 E-alum = 10x10^6 lbs/in^2. P Steel Steel Aluminn O 3520 lbs O 2440 lbs 4450 lbs O 4550 Ibs

For the given figure below, determine the force that would cause the bar to deform by 1.8x10^-2 inches. Other properties: x-sectional area: 0.25 in^2. E-steel = 29x10^6 lbs/in^2 E-alum = 10x10^6 lbs/in^2. P Steel Steel Aluminn O 3520 lbs O 2440 lbs 4450 lbs O 4550 Ibs

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter8: Engineering Materials

Section: Chapter Questions

Problem 7ETSQ

See similar textbooks

Related questions

Q: Problem The compound shaft is subjected to the torque as shown in the figure. Find the required diam...

Q: 50 lb/it 200 lb-ft - 20 ft- 10 ft -

Q: Find out the safe load P carried by the bracket at an eccentricity of 300mm to a column thr 6 bolts ...

A: Step 1: d=20mm d0=22mm fu=410 MPa tf=9.1mm Design shear strength of blots= 45272 N Kb is least of p/...

Q: Design a concrete mix for use in plain cement concreté (PCC) from the following data : Characteristi...

Q: Given data : Mass=2 kg Velocity=3 m/s Determine kinetic energy

A: Introduction : The energy in body due to motion is called kinetic energy . For a body to have kineti...

Q: Given data : Work done=16 J Distance moved%38 m Determine the force

Q: A certain force F has a moment of 18Q N-m dockwise about point O and 9T N-m counterdockwise about po...

A: Hi there! since you have not given the value of Q and T so, I am taking it as 0.

Q: For sitework computation: If a footing labeled as F-4 (occurring 3 times on the foundation plan) is ...

Q: section 0.3 m by 0.3 m is driven 15 m inte consolidated clays with properties as de From the ground ...

A: According to given data A square prestressed concrete pile with a cross section 0.3 m by 0.3 m is d...

Q: The vertical reducing section shown in the figure contains oil with S flowing upward at the rate of ...

Q: Determine the force of the members CF and CG. 2 kN 2 m В 2 m 2 m A SN kN 3 m F E

Q: The circular tube with the cross section shown is subjected to the axial force P and bending moment ...

Q: Solve the support reaction at B. 16 k :黃 2 k/ft 8 k 3k/ft A D F 12 ft8 ft- -- 9 ft- 12 ft +9 ft- 3 f...

Q: e Models of Surface irrigation system design?

Q: A proposed industrial building will carry unfactored column loads ranging from 280 to 1,200kN and se...

A: given

Q: Assuming elastic behavior, why does the maximum shear stress always correspond to the neutral axis l...

A: Step: 1 Shear stress: - When a load acts parallel to face of cross- section then it produces a shea...

Q: A. In the figure, a longitudinal hole is bored across the length of a cantilever beam having a recta...

Q: A 16 in square concrete column carries factored ultimate column loads of PU = 370 k andMU = 70 k@ft....

A: Given; Factored ultimate column load,Pu=370 k Factored ultimate moment,Mu=70 k-ft C/S dimension of s...

Q: The line of action of force F1 = 3TT N is passing through point A(+2,+3,+1) towards B(+5,+5,+4), whi...

Q: Example 2 What is the volume of air needed to burn 1000 m' of gaseous fuel containing methane 30%, h...

Q: Compute the length of a vertical summit curve having tangent grades of 3% and -3% if the passing sig...

Q: 5. A nail and a hammer are modeled by a linear spring and an incident mass according to the figure. ...

A: To determine the maximum force between the hammer and the nail, and the duration of the impulse. G...

Q: If the 3-day BOD (BOD3) of a waste is 100 mg/L & the BOD decay constant, k is 0.345 per day, its ult...

Q: Why is it essential to measure the porosity and permeability of the soil?

Q: Find Inside Area of these Rooms and inside Length of the walls 10.0 3.2 4,5- R0.7 R0,6 A1 2,1 A4 2.2...

A: To Determine Inside Area of these Rooms and inside Length of the walls.

Q: A water company wants to check that it will have sufficient water if there is a prolonged drought in...

Q: A proposed building column will carry a downward maximum unfactored load combinationof 250 k and a s...

A: load combination-250 k service load -185 k g - 119 lb/ft3 da- 0.75 in c′ = 0, f′ = 32°, N60 = 30

Q: 2. Figure 2 shows a 0.8 m wide of rectangular sluice gate is hinged at point A on the wall of a rese...

Q: The man stands 60 ft from the wall and throws a ball at it with a speed of 50 ft/s. Determine the an...

A: The man stands 50ft form the wall and throws ball at speed vo= 50ft/s Height of ceiling = 20ft It ha...

Q: A triangular slab ABC shown in Fig. 15.7 is simply supported along edges AB and AC but has a free ed...

Q: section rx = 209 mm ly = 16.1 x 106 m Sy = 156 000 mr mm?

A: work out admissible development of the beam according to ASDallowable movement MB=Fy×Sx ...

Q: of a so that the resultant of the three forces is to be vertical, and (b) the sultant force. Lastly ...

Q: Absolute value of bending torque Max = ? kNm Width of the web (integer) = ? mm

A: Given Data: The yield strength of the aluminum material of the beam is σy=280 MPa The width of the b...

Q: B 1.5P 35° 35° 55° 4 m 4 m

Q: The weights of Crates A and B are 150 lb and 50 lb, respectively. Determine their speed when they be...

Q: 2-43. If 30 and F-250 lb, determine the magnitude of the resultant force acting on the bracket and i...

Q: 2. A tension member has a span of 9 m and carries a tensile load of 981 kN. The member is to have tw...

Q: A wide flange section has the following properties. A = 6645 mm2 bf = 152.40 mm tf = 10.80 mm %3D d ...

Q: Design this simply supported beam with double overhangs and provide the required reinforcement so it...

Q: Determine the allowable value of force P (in Newtons), if a bar of diameter d = 23 mm and length L =...

A: Given, Length L= 0.90 m=900 mm d=23 mm modulus E= 47 GPa Allowable normal stressσallowable =137 MPa

Q: Determine the Maximum positive shear from the shear diagram. Attach here the shear diagram and compu...

Q: You have been instructed to join two existing roads by an even grade from point X to Y. Point X is a...

A: Given data:

Q: The cable structure shown in figure 6.4 is used to support a roof for outdoor activities. Determine ...

A: Determination of maximum horizontal component of tension in cable##

Q: Find the R value of a pane of 0.125-in thick glass

Q: A beam is simply supported at the left end and is fixed at the right end. It is subjected to a conce...

A: According to given data A beam is simply supported at the left end and is fixed at the right end. I...

Q: A simple beam having a span of 10m carries a dead load (including its own weight) of 6.5 kN/m. The b...

A: Step 1: W =6.5 kN/m Design Shear force = 6.5 x 10/2 =32.5 kN Design Moment= 6.5 x 102/8 =81.25 kNm ...

Q: e) Given the household and demographic data presented in Table 1, calculate the total number of AM P...

A: Calculate the value of TA , and TP by using formula as given as, TA=1500+8.5I+0.15A0+0.05ARTP=0.4V+0...

Q: pls answer with solution choices: in kg/m3 490 8050 77000 7850

Q: The declination at a point Q is 3* 15 east. The true bearing of a line QR is S 30* 30' W. The magnet...

A: To find magnetic bearing of line

Q: The rigid bar ABC shown is hinged at A and supported by a steel rod at B. Determine loadP that can b...

Concept explainers

Wind Energy

Wind energy is a renewable energy source that is used to generate electricity by wind power. The term, wind power, means utilization of kinetic energy of wind to generate electricity. Wind energy is termed renewable source energy because it can never be exhausted. There are other renewable energy sources, such as solar energy, geothermal energy, hydropower energy, and so on. All of them contribute to power the thermal energy stations to generate electricity.

Question

Consider the given choices

For the given figure below, determine the force that would cause the bar to deform by
1.8x10^-2 inches. Other properties:
x-sectional area: 0.25 in^2.
E-steel = 29x10^6 lbs/in^2
E-alum = 10x10^6 lbs/in^2.
tom
P
Steel
Steel
Aluminn
O 3520 lbs
O 2440 Ibs
4450 lbs
O 4550 Ibs

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Please show solutions on how to get the 1500 value. The circle green in the figure. Civil engineering- steel design Note: I thought the value of area 2 is 3750. Area 2: 25x150= 3750 mm2. Feel free to correct me . What should put in circle in the figure.
An alloy steel having a diameter of 0.45 in. extends 0.002 in. over a gage length of 2.2 in. due to a tensile load of 3900 lb. What is the modulus of elasticity of this alloy steel? A)29,010 ksi B)27,000 ksi C)30,000 ksi D)28,000 ksi
Answer 2.78in Please fast. A steel bar showed a percentage reduction in cross-sectional area of 19.5%. The final diameter of the bar was 2.5 in. Calculate the initial diameter of the bar.
Create a diagram and describe the following terms: 1. 2. Wood 3. Unfinished Lumber 4. S2- and S4-types 5. Cobblestone (lumber) 6. Undressed or Surface Lumber 7. Wood Plank 9. Plywood ten (lumber) Eleven. Flitch. Twelve. Fine-grained. 13. Cross-grained or crooked
The compound bar containing steel, bronze, and aluminum segments carries the axial loads shown in the figure. The cross-sectional area of the steel, bronze, and aluminum are 0.75 in2, 1.08 in2, and 0.56 in2 respectively.Determine the change in length (in inches) of the bar if P = 11599 lb.The moduli of elasticity are 30022 ksi for steel ,12071 ksifor bronze, and 10028 ksi for aluminum. Round off the final answer to four decimal places.
A steel plate (called a cover plate) having cross-sectional dimensions W2 5.0 in. x 0.4 in. is welded along the full length of the bottom flange of a W, 12.0 in. x 87.0 in. wide-flange beam (see the figure, which shows the beam cross section). I W2 cover plate What is the percent increase in the smaller section modulus (as compared to the wide-flange beam alone)? Round your answer to two decimal places. % in smaller section modulus =
Unit for Reinforcing Bars a. Kilograms b. Tons c. Pieces d. All of the above
HELP WITH COMPLETE SOLUTION AND 4 DECIMAL PLACES, PLEASE DO NOT MAKE IT COMPLICATED THANK YOU Line AB was determined to be 2395.25m when measured with a 30m‐steel tape supported throughout its length under a pull of 4kg and at a mean temperature of 35°C. The cross‐sectional area of the tape is 0.03 cm^2, coefficient of thermal expansion is 0.0000116/°C and modulus of elasticity of steel is 2.0x10^6 kg/cm^2. Determine a. Correction for the measured length due to temperature if the tape usedis of standard length at a temperature of 20°C. Is the tape too long or tooshort? b. Correction for the measured length due to tension if the tape used isof standard length at a pull of 5 kg. Is the tape too long or too short? c. Correction for the measured length due to sag if it weighs 0.04kg/m d. the corrected length of line AB considering corrections from (a), (b) and (c)
Please solve in handwritting step by step. again in hand writting.
Calculate all 5 failures paths. Show step by step solution. A flat bar PL 12.7mm X 165mm Cross sectional area is 2095.5mm2 in metric Imperial units must be converted to metric Textbook reference: Handbook of steel construction CISC
multiply and simplify the following: (2x-1)(x2-3x+25)
A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the figure. The cross-sectional area of the bronze, aluminum, and steel are 412 mm2, 601 mm2 , and 260 mm2 respectively.Determine the change in length (in mm) of the bar if P = 30280 N.The moduli of elasticity are 81.17 GPa for bronze ,71.07 GPafor aluminum , and 202.36 GPa for steel . Round off the final answer to four decimal places.