The figure shows a heat engine (HE) working between two reservoirs. The amount of heat (Q2)rejected by the heat engine is drawn by a heat pump (HP). The heat pump receives the entireworkoutput(W)oftheheatengine.Iftemperatures.T₁ > T3 > T2, then the relation between the efficiency (n) of the heat engine and the coefficientof performance (COP) of the heat pump is#HEHPT.a

Given data; Temperatures T1>T3>T2Heat pump receives the entire work output (W) of the heat…

Answered: (COP) of the heat pump is

Engineering

Mechanical Engineering

(COP) of the heat pump is

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A thermodynamics steady flow system receives 4.56 kg/min of a fluid where the pressure is 137.9 Kpa specific volume of 0.0388 m3/kg, velocity of 122m/s and internal energy of 1160Kj/Kg. the fluid leaves the system at a boundary where pressure is 551.6Kpa , specific volume of 0.193 m3/kg , velocity of 183 m/s and internal energy of 52.8 Kj/kg. during the passage through the system, the fluid receives 3,000 Joules/s of heat. Determine the steady flow work in. Kj/min and kj/s
A heating system must maintain the interior of a building at TH = 20°C when the outside temperature is TC = 2°C. If the rate of heat transfer from the building through its walls and roof is 16.4 kW, determine the electrical power required, in kW, to heat the building using (a) electrical-resistance heating, (b) a heat pump whose coefficient of performance is 3.0, (c) a reversible heat pump operating between hot and cold reservoirs at 20°C and 2°C, respectively.
A heat pump with a COP of 3.2 is used to heat a perfectly sealed house (no air leaks). The entire mass within the house (air, furniture, etc.) is equivalent to 1200 kg of air. When running, the heat pump consumes electric power at a rate of 5 kW. The temperature of the house was 7°C when the heat pump was turned on. If heat transfer through the envelope of the house (walls, roof, etc.) is negligible, the length of time the heat pump must run to raise the temperature of the entire contents of the house to 22°C is (a) 13.5 min (b) 43.1 min (c) 138 min (d) 18.8 min (e) 808 min
A power station with an efficiency e generates W watts of electric power and dissipates D J of heat energy each second to the cooling water that flows through it. The cooling water increases its temperature by T degrees of Celsius. Find the mass of cooling water which flows through the plant each second. Specific heat capacity of water cw = 4,184 J/kgC e = 0.2W = 4.9 x 108 wattsD = 2.5 x 108 JT = 4 C Enter value in tons (1 ton = 1000 kg).Enter two digits after decimal point.
give a specific example of a process that has the energy changes and transfers described. (For example, if the question states “ΔEth > 0, W = 0,” you are to describe a process that has an increase in thermal energy and no transfer of energy by work. You could write “Heating a pan of water on the stove.”) ΔEth < 0, W ≠ 0, Q ≠ 0
A student buys a 5000 Btu window air conditioner for his apartment bedroom. He monitors it for one hour on a hot day and determines that it operates approximately 60 percent of the time (duty cycle = 60 percent) to keep the room at nearly constant temperature. (a) Showing all your work and using unity conversion ratios, calculate the rate of heat transfer into the bedroom through the walls, windows, etc. in units of Btu/h and in units of kW. (b) If the energy efficiency ratio (EER) of the air conditioner is 9.0 and electricity costs 7.5 cents per kilowatt-hr, calculate how much it costs (in cents) for him to run the air conditioner for one hour.
2. A gas undergoes a thermodynamic cycle consisting of the following processes:i) Process 1-2: Constant pressure p1 = 1.4 bar, V1=0.028 m3, W1-2=10.5 kJii) Process 2-3: Compression with pV=Constant, U3=U2iii) Process 3-1: Constant Volume, U1-U3 = -26.4 kJThere are no significant changes in KE and PEi) Sketch the cycle on a p-V diagramii) Calculate the network for the cycle in kJiii) Calculate the heat transfer for process 1-2iv) Show that ƩW = ƩQ
A closed system executes a series of processes for Wn = 80 BTU, U1 = 40 BTU and U2 = 5 BTU are given for each process. What is the value of heat in BTU? Is it added or rejected?
during the working stroke of an engine the heat transferred out of the system was 160kJ/kg of working substance. the internal energy also decreased by 405kJ/kg of working substance. Determine the work done
The figure below shows a turbine-driven pump that provides water to a mixing chamber located dz⁢= 5 m higher than the pump, where m˙=50 kg/s. Steady-state operating data for the turbine and pump are labeled on the figure. Heat transfer from the water to its surroundings occurs at a rate of 2 kW. For the turbine, heat transfer with the surroundings and potential energy effects are negligible. Kinetic energy effects at all numbered states can be ignored. Determine:(a) the magnitude of the pump power, in kW.(b) the mass flow rate of steam, in kg/s, that flows through the turbine.
Energy balance results (in kW) obtained for the same medium speed single cylinder diesel engine are reported in the following table. For case 1, if the coolant temperature is 105 °C at the outlet of the engine and the volumetric flow rate is 0.22*10-3 m3/s, the temperature of the coolant at the inlet is (in °C): (The coolant is considered water with a density 999 kg/m3 and a specific heat 4.2 k/kg.K). Case N (rpm) bmep (bar) W. O ambient Q ahast shaft 2.2 4.2 19.1 60.3 9.90 3.52 1 500 7.1 24.5 23.8 500 6.1 3.6 5.2 400 3.50 4.9 4.1 1.4 Select one: O a. 142.1 O b. 112.7 O c. 97.31 O d. 87.2 O e. 370.31
A heat pump cycle delivers energy by heat transfer to a dwelling at a rate of 40,000 Btu/h. The coefficient of performance of the cycle is 2.8. Evaluating electricity at $0.085 per kW•h, determine the cost of electricity during the heating season when the heat pump operates for 2000 hours.