Correct any seven of the following sentences, using suitable phrases. 1. The Z-parameters is called the current equation. 2. Maximum power transfer occur when the Z₁ is equal to the Zh at the load terminals. 3. Two-port network could be used to transfer the average energy to the load. 4. In the case all the flux is transferred between two coils, the coupling coefficient is greater than ha 5. When the total reactance is less than sum of two mutual reactance's, the connection is series add. 6. The current passing through the coil itself will produce a mutual voltage. 7. The generator power is always less than the maximum power transferred to the load?.

Correct any seven of the following sentences, using suitable phrases. 1. The Z-parameters is called the current equation. 2. Maximum power transfer occur when the Z₁ is equal to the Zh at the load terminals. 3. Two-port network could be used to transfer the average energy to the load. 4. In the case all the flux is transferred between two coils, the coupling coefficient is greater than ha 5. When the total reactance is less than sum of two mutual reactance's, the connection is series add. 6. The current passing through the coil itself will produce a mutual voltage. 7. The generator power is always less than the maximum power transferred to the load?.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.52P

See similar textbooks

Similar questions

A 500 KV ,300 km transmission line has following line parameters.X=0.36 ,Y=5.2*10^-6 s/km calculate characteristic impedence,Propagation constant,surge impedence loading.The transmission line mentiotioned above delivers 1200 MW load at unity pf and the load voltage is 500 KV,Determine the sending end vlotage and current
a) Calculate the unit ramp input steady state error (e_ss) for the following control system. b) Δ(s)=2s^3+2s^2+s+K calculate the range of K values over which the system is stable, given the characteristic polynomial.
2) 400 km, 138 kV, 50 Hz transmission line has the following parameters: r=0.106Ω/km,x=0.493Ω/km, y=j3.36 x 10-6 S/km. Losses are neglected.(a) Compute the corresponding ABCD parameters (use T equivalent circuit and derive the relatedequations).
A single phase, 50Hz transmission line connected between two buses having line resistance of 3Ω, inductive reactance of 0.2 Henry. Both the ends of transmission lines are connected with series capacitors of 400microfarads each for series compensation. Then series impedance of the line is a.(3-j31) Ω b.(3-j59.6) Ω c.(3+j31)Ω d.(3+j59.6) Ω 2- Fast decoupled algorithm is not as accurate as the exact Newton Raphson algorithm for Variable number of iteration Fixed number of iteration Variable time per iteration Fixed time per iteration
TOPIC: Transmission Lines, Power Systems, and Powerplants:INSTRUCTIONS:- Answer in this format: Given, Illustration, Required Conversion, Solution, Final Answer.- Step-by-step solution, do not skip even simple calculations to avoid confusion.- If answered in written form, make sure it is readable.PROBLEM:A 138-kV, three-phase short transmission line has a per-phase impedance of (2 + 14) 2. If the line supplies a 25-MW load at 0.8 power factor lagging, calculate the sending-end voltage in kV. 139.8 137.9 139.5 138.6
What are the transformation relations between the scattering (S) parameters and the Z, Y, ABCD and T parameters?( NEED NEAT HANDWRITTEN SOLUTION ONLY OTHERWISE DOWNVOTE).
a) In a single line bus system with the impedance characterizes of the following R = 0.15pu while XL = 0.45pu. Find the inverse of the impedance given that Z = R + jx. b) Given the following line impedance of a four-bus system, obtain its admittance matrix. Line (bus to bus) : 1 - 2 1-3 2-3 2-4 3-15 Rpu : 0.05 0.10 0.15 0.10 0.05 Xpu : 0.15 0.30 0.45 0.30 0.15 c) Identify three (3) residual measures you can use to mitigate the effects on the power system frequency d) Enumerate 3 voltage control equipment and its usage
What should ZL be for the maximum power transfer in the circuit given below and calculate the maximum power
2) A 3-bus power system is shown below. The three busses are connected through three 340 kV transmission lines of 200km, 150 km, and 150 km long. These transmission lines have the series resistance of 0.05 Ω/km and series reactance of 0.3Ω/km. (a) Find the value of the transmission lines series impedances. (b) Find the bus admittance matrix (Y-bus) of this power system.
a) What is the use of Schering bridge in measurement system? b) Draw the schematic diagram of Anderson's bridge. c) Write down the balanced equations for Maxwell's bridge.
If the power system has 'n' number of generators, then the size of the B- coefficient matrix is (nxn). Select one: True False
175 km, 138 KV, 50 Hz transmission line has the following distributed parameters: r = 0.24 Ω/km, x = 1.12 Ω/km, y = j7.68 x 10 ‾⁶ S/km. Losses are neglected. (a) Compute the nominal π equivalent circuit parameters and draw the circuit. (b) Derive the corresponding ABCD parameters. (c) The line delivers 40 MW at 132 kV with a power factor of 0.95 lagging (Δ connected). Using the ABCD parameters, compute the sending end voltage, current and δ angle. (d) Draw the approximate voltage profile of this line for the following power delivered: (i) 0 MW, 15 MW, 45 MW, and surge impedance loading. Indicate the methods available to maintain the voltages within the range of 0.97 and 1.03.