(cp = 1.005 kJ/kg.K, cy = 0.718 kJ/kg.K, R= 0.287 kJ/kgK, k =1.4) %3D P= 100 kPa In an ideal Brayton cycle operating according to the acceptance of air standards, air enters the compressor at 20 °C and 100 kPa pressure. The highest temperature of the cycle is 1100 °C. Since the mass flow rate of the air is 10 kg/s and the pressure ratio of the cycle is 12, (Assume the specific heats do not change with temperature.) a) Find the compressor work (kW). b) Find the turbine work (kW). c) Find the amount of heat (kW) entering the system. d) Find the thermal efficiency of the cycle.

(cp = 1.005 kJ/kg.K, cy = 0.718 kJ/kg.K, R= 0.287 kJ/kgK, k =1.4) %3D P= 100 kPa In an ideal Brayton cycle operating according to the acceptance of air standards, air enters the compressor at 20 °C and 100 kPa pressure. The highest temperature of the cycle is 1100 °C. Since the mass flow rate of the air is 10 kg/s and the pressure ratio of the cycle is 12, (Assume the specific heats do not change with temperature.) a) Find the compressor work (kW). b) Find the turbine work (kW). c) Find the amount of heat (kW) entering the system. d) Find the thermal efficiency of the cycle.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The pressure and temperature at the beginning of compression of an air-standard Diesel cycle are 100 kPa and 300 K, respectively. At the end of the heat addition, the pressure is 6821 kPa and the temperature is 2050 K. Determine a. the compression ratio. b. the cutoff ratio. c. the thermal efficiency of the cycle. d. the mean effective pressure, in kPa.
At the beginning of the compression process of air-standard Diesel cycle operating with a compression ratio of 18, the temperature is 300 K and the pressure is 0.1 MPa. The cut-off ratio for the cycle is 2 and the mass flow rate in the system is 1900 kg/hr. Cp= 1.006 kJ/kg K Cv= 0.717 kJ/kg K 1) which figure represents the diagram for the process 2) which formula should be used to determine the temperature after compression? 3) calculate the temperature after isentropic compression in the presentable unit 4)which formula should be used to determine the temperature after heating? 5) calculate the temperature after isentropic compression in the presentable unit? 6) calculate the temperature after isentropic expansion in the presentable unit? 7) calculate the pressure after compression in kPa ? 8) which formula should be used to determine the work output of the engine? 9) calculate the work output of the engine kW? 10) calculate the thermal efficiency of the cycle in %? 11) which…
The pressure and temperature at the beginning of compression of an air-standard Diesel cycle are 100 kPa and 300 K, respectively. At the end of the heat addition, the pressure is 6821 kPa and the temperature is 2050 K. Determine:(a) the compression ratio.(b) the cutoff ratio.(c) the percent thermal efficiency of the cycle.(d) the mean effective pressure, in kPa.
At the beginning of the compression process of air-standard Diesel cycle operating with a compression ratio of 18, the temperature is 300 K and the pressure is 0.1 MPa. The cut-off ratio for the cycle is 2 and the mass flow rate in the system is 1900 kg/hr. Cp=1.006 kJ/kg K Cv= 0.717 kJ/kg K 1) calculate the thermal efficiency of the cycle in %? 2) which formula should be used to determine the thermal efficiency of the cycle ?
Calculate the efficiency of an Diesel cycle assuming Cold Air-Standard Analysis operating in air (k= 1.4) with a compression ratio of 20 and a cutoff ratio of 1.7? (Enter your answer as a percent to the nearest 1/10th)
Question No.14: In an SI engine working on the ideal Otto cycle the compression ratio is 6. The pressure and the temperature at the beginning of compression are 1.013 bar and 27°C respectively. The Peak pressure is 30 bar. Determine the pressure and temperature at the salient points, the air standard efficiency and the mean effective pressure. Assume γ = 1.4
The pressure and temperature at the beginning of compression of a cold air-standard Diesel cycle are 90 kPa and 300 K, respectively. At the end of the heat addition, the pressure is 7.2 MPa and the temperature is 2050 K. Assume constant specific heats evaluated at 300 K.Determine:(a) the compression ratio.(b) the cutoff ratio.(c) the percent thermal efficiency of the cycle.(d) the mean effective pressure, in kPa.
The pressure and temperature at the beginning of compression of an air-standard Diesel cycle are 80 kPa and 300 K, respectively. At the end of the heat addition, the pressure is 6821 kPa and the temperature is 2150 K. (a) Determine the compression ratio. r = (b) Cutoff Ratio (c) Thermal Efficiency (d) Mean Effective Pressure
The pressure and temperature at the beginning of compression of an air-standard Diesel cycle are 90 kPa and 300 K, respectively. At the end of the heat addition, the pressure is 6821 kPa and the temperature is 1950 K. Determine: (a) the compression ratio, r. (b) the cutoff ratio, rc. (c) the thermal efficiency of the cycle, ?th (%). (d) the mean effective pressure, mep (kPa).
Air enters the compressor of an ideal air standard Brayton cycle at 100 kPa, 290 K, with a mass flow rate of 6 kg/s. The compressor pressure ratio is 10. The turbine inlet temperature is 1500 K. If a regenerator with an effectiveness of 70% is incorporated in the cycle, determine (i)turbine work, (ii) compressor work, (iii) heat supplied, and (iv) the efficiency of the cycle. Draw a suitable block diagram and T-s diagram. Take Cp=1.005 kJ/kg K and ϒ= 1.4
The temperature at the beginning of the compression process of air-standard otto cycle with a compression ratio of 10 is 21 °C , the pressure is 101 kPa, and the mass flow rate of air in the engine is 580 kg/min. The maximum temperature during the cycle is 1300 °C. Cp= 1.006 kJ/kg K Cv= 0.717 kJ/kg K 1) calculate the temperature after isentropic expansion in the presentable unit? 2) which formula should be used to determine the power obtainable from the cycle? 3calculate the power obtainable from the cycle in kW?
Given the same compression ratio for both air standard Otto and air standard Diesel cycle, which cycle has higher thermal efficiency? Answer the same question this time for the Otto cycle versus the Brayton cycle