mat 8 Current Attempt in ProgressA U-tube manometer is connected to a closed tank as shown in the figure below. The air pressure in the tank is 0.50 psi and the liquid inthe tank is oil (y = 54.0 lb/ft³). The pressure at point A is 2.00 psi. Determine: (a) the depth of oil, z, and (b) the differential reading, h, onthe manometer.(a) z =(b) h =ftftAirOilSG = 3.021.6ftOpenh

Answered: Image /qna-images/answer/5f93ab0e-0eaf-413e-936c-33acfcf78431.jpg

Current Attempt in Progress A U-tube manometer is connected to a closed tank as shown in the figure below. The air pressure in the tank is 0.50 psi and the liquid in the tank is oil (y = 54.0 lb/ft3). The pressure at point A is 2.00 psi. Determine: (a) the depth of oil, z, and (b) the differential reading, h, on the manometer. (a) z = (b) h = ! ft ft Air Oil A SG=3.02- 1.6ft Open

Current Attempt in Progress A U-tube manometer is connected to a closed tank as shown in the figure below. The air pressure in the tank is 0.50 psi and the liquid in the tank is oil (y = 54.0 lb/ft3). The pressure at point A is 2.00 psi. Determine: (a) the depth of oil, z, and (b) the differential reading, h, on the manometer. (a) z = (b) h = ! ft ft Air Oil A SG=3.02- 1.6ft Open

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The differential mercury manometer is connected to pipe A containing gasoline (SG = 0.65), and to pipe B containing water. Determine the differential reading, h, corresponding to a pressure in A of 20 kPa and a vacuum of 150 mm Hg in B. Express the answer in meters (m).
A U-tube manometer is connected to a closed tank as shown in Fig. below. The air pressure in the tank is 120 Pa and the liquid in the tank is oil (γ = 12000 N/m3). The pressure at point A is 20 kPa. Determine: (a) the depth of oil, z, and (b) the differential reading, h, on the manometer.
1. A U-tube manometer is connected to a closed tankc ontaining air and water is shown. At the closed end of the manometer the air pressure is 16 psia.Determine the reading on the pressure gage for a differential reading of 4 ft on the manometer.Express your answer in psi (gage). Assume standardatmospheric pressure and neglect the weight ofthe air columns in the manometer. (Figure 1) 2. Two pipes are connected by a manometer as shown.Determine the pressure difference, between the pipesin kPa. (Figure 2)
1. The horizontally lying device or fitting shown below connects three pipelines. Water (γwater = 9.81 kN/m3 ) enters the device through A with a speed VA = 8 m/s and a pressure PA = 70 kPa . Water exits through C at 9 m/s. Friction and minor head losses through the device are negligible. Note that B and C are not at atmospheric pressure. (a) Calculate the speed and flow rate of the water at B. Is the water flowing through B flowing into to the device or out of the device? (b) Calculate the pressures at B and C, PB and PC.
Subejct: Hydraulics/Fluid Mechanics Oil of sp.gr. of 0.750 flows through the nozzle shown and deflects the mercury in the U-tube gage. Determine the value of H in m if the pressure at A is 142 kPa.
A cylindrical tank contains water at a height of 55 mm, as shown. Inside is a small open cylindrical tank containing cleaning fluid (s.g = 0.8) at a height h. The pressure Pb=13.4 kPa gage and Pc=13.42 kPa gage. Assume the cleaning fluid is prevented from moving to the top of the tank. Use unit weight of water = 9.79 kN/m^3. (a) Determine the pressure Pa in kPa, (b) the value of h in mm, and (c) the value of y in millimeters.
A pump draws water from a reservoir A and lifts it to reservoir B as shown. The loss of head from A and lifts it to reservoir B as shown. The loss of head from A to (1) is 5 times the velocity head in the 12-inch pipe and the loss of head from (2) to B is 23 times the velocity head in the 7-inch pipe. Compute the pressure heads (2) in ft when the discharge is 447 gpm. Round your answer to 2 decimal places.
4.) A 75 mm diameter pipe, 2 m long is just filled with oil (sp. gr. = 0.822) and then capped, and place on horizontal position. It is rotated at 27.5 rad/sec about a vertical axis 0.5 m from one end (outside the pipe). What is the pressure in kPa at the far end of the pipe? Answer: 1865 Kpa Subject: Fluid Mechanic Lesson: Relative Equilibrium of Liquids Fundamentals of Fluid Flow
Question - Civil hydraulics The diameter of the U-tube is one-tenth the diameter of the enlarged ends, and a double column enlarged ends manometer is used to measure a minor pressure differential between two points of a system transporting air under pressure. Water is employed as the heavy liquid, and oil with a relative density of 0-82 is used as the lighter liquid in both limbs. Calculate the difference in pressure in millimetres of water for a manometer displacement of 50 mm, presuming the lighter liquid's surfaces stay in the larger ends. If carbon tetrachloride, which has a relative density of 1.6, were used in place of water but the pressure conditions remained the same, what would the manometer read?
3.Water flows from a tank through 22 meters of 150–mmdiameter pipe and then discharges into air as shown in the figure. The flow of water in the pipe is 120 L/s.Assume n = 0.013 and neglect minor losses. a. Find the velocity of flow in the pipe in m/s. b. Determine the total head loss in the pipe in meters. c. Calculate the pressure at the top of the tank in kPa.
Based on the provided differential-type manometer, calculate the difference in the pressure between points A and B (as in Δp = pA - pB = ?). SG of oil is 0.8
. A pump draws water from a reservoir and conveys it to another reservoir 30 m above. The sucLon pipe is 100 mm in diameter and 10 m long while the delivery pipe is 100 mm in diameter and 150 m long. if the velocity in the pipe is 3 m/s, the fricLon factor of the pipe 0.008, and the pump and motor efficiencies 85 % and 92 %, respecLvely. See Figure Q6.1. Calculate:(a) Gauge pressure at the pump's inlet (at C) (10)(b) Gauge Pressure at the pump's outlet (at D) (10)(c) input power to motor (5)