Current Attempt in Progress Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sy 58 ksi, Sy 15 ksi, and Sy = 18 ksi. (a) Draw Mohr's circle for this state of stress. (b) Determine the principal stresses and the maximum in-plane shear stress acting at the point. (c) Show these stresses on an appropriate sketch (e.g., see Fig. 12.15 or Fig. 12.16). (d) Determine the absolute maximum shear stress at the point.

Current Attempt in Progress Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sy 58 ksi, Sy 15 ksi, and Sy = 18 ksi. (a) Draw Mohr's circle for this state of stress. (b) Determine the principal stresses and the maximum in-plane shear stress acting at the point. (c) Show these stresses on an appropriate sketch (e.g., see Fig. 12.15 or Fig. 12.16). (d) Determine the absolute maximum shear stress at the point.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.3.1P: The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the...

See similar textbooks

Similar questions

Can you help me with this problem, please: At a material point in plane stress it is known that the hydrostatic component of the stress is 15 ksi and that the second stress invariant is 30 ksi. Determine the magnitude of the principal stresses and the maximum shear stress.
Explain the method of representing the combination of normal and shear stresses acting on any plane through an incremental element on shear stress–normal stress coordinates.
A rectangular block of material is subjected to a shear stress of 30MN/m2 together with it's associated complementary shear stress. Determine the magnitude of the stresses on a plane inclined at 30 degrees to the directions of the applied stresses,which may be taken as horizontal
The principal stresses at a point across two mutually perpendicular planes are 70 MN/m2 tension and 50 MN/m2 tension respectively. The shear stress across these planes is 30 MN/m? (Counter clockwise). Determine the magnitude of the normal, tangential, the resultant stress, and inclination of resultant stress on a plane inclined at 30° to the plane of greater principal stress. And also verify the answer by drawing the Mohr's circle.
A body is subjected to a direct tensile stress of 300 MPa in one plane accompained by a simple shear stress of 200 MPa. Determine maximum normal stress on the plane.
Considering the original state of stress as shown in figure below and recalling the already developed equations for normal and shear stress at an angle Ɵ c.c.w from x-axis, mathematically prove that the planes of maximum in-plane shear stress are inclined at 45o to the principal planes.
The principal stresses at a point across two mutually perpendicular planes are 70 MN/m2 tension and 55 MN/m2 tension respectively. The shear stress across these planes is 25 MN/m2 (Counter clockwise). Determine the magnitude of the normal, tangential, the resultant stress, and inclination of resultant stress on a plane inclined at 25o to the plane of greater principal stress. And also verify the answer by drawing the Mohr’s circle.
Direct stresses of 160N/mm tensile and 120 N/mm compressive exist on two perpendicular planes at a certain point in a body. They are also accompanied by shear stresses on the planes. The greatest principal stress at the point due to these is 200 N/mm?. a) What must be the magnitude of the shearing stresses on the two planes? b) What will be the maximum shearing stress at the point?
For the element shown below, determine: 1- The principal stresses and the maximum in-plane shear stress acting at the point by using equations, then show these stresses on an appropriate sketch. 2- The normal stresses 0 n and ¢ t and the shear stress T nt for element oriented 20° clockwise from the position shown, using Mobhr’s Circle. 75 MPa
a) Prime planes,b) Prime stresses, c) Maximum shear stress and thisin the plane of the stressdetermine the normal stress
Using Mohr's circle on each case, determine a)The principal stresses and maximun shear stress. Show all results on sketches of properly oriented elements b)Is there the invariance of normal stresses in each case?
For the stresses of plane stress state is ?? = −8 ??? , ?? = 7 ??? and??? = −6 ???Draw a Mohr’s circle diagram.Draw stress element for the given stressesFind the principal normal and shear stresses, and determine the anglefrom the x axis to ?1Draw the stress element for the principle stress.Using stress transformation, find the principle stresses and the angle of ?1Determine the stress transformation for the angle ∅ = 25° #Answer all in detail