Current Attempt in Progress Two 4-in.-wide wooden boards are to be joined by splice plates that will be fully glued onto the contact surfaces, as shown in the figure. The glue to be used can safely provide a shear strength of 150 psi. Determine the smallest allowable length L that can be used for the splice plates for an applied load of P = 13,000 lb. Note that a gap of a = 0.8 in. is required between boards (1) and (2). (1) (2) Answer: L = in.

Current Attempt in Progress Two 4-in.-wide wooden boards are to be joined by splice plates that will be fully glued onto the contact surfaces, as shown in the figure. The glue to be used can safely provide a shear strength of 150 psi. Determine the smallest allowable length L that can be used for the splice plates for an applied load of P = 13,000 lb. Note that a gap of a = 0.8 in. is required between boards (1) and (2). (1) (2) Answer: L = in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

•Timber beamSafe working stress = 25 MPaCross-section dimensions:height = 119 mm,width = 66 mmProving ring number 293. Steel beam Safe working stress = 200 MPa Cross-section dimensions:external height = 149 mm,external width = 50 mm,wall thickness = 3.0 mm,Proving ring number 1522.1)Calculate safe max bending moment in the central part of the beam using Mmax = (I)(max stress)/(D/2)2) calculate Safe applied force in the proving ring or tie rod, assuming a symmetrical setup as in the photowith a ‘lever arm’ of 600 mm
A simply supported beam has a maximum moment equal to 15 KN. The beam has a width of 200 mm and a depth of 250 mm and is made up of 80% grade Narra. What is the actual shearing stress of the beam in MPa? Blank 1 (use two decimal places, no need for unit) with complete diagram and solution
If the clamping force on the boards is 600 lb, determine the required magnitude of the couple forces that must be applied perpendicular to the lever AB of the clamp at A and B in order to loosen the screw. The single squarethreaded screw has a mean diameter of 1 in. and a lead of 0.25 in. The coefficient of static friction is μs = 0.3.
Two 4-in.-wide wooden boards are to be joined by splice plates that will be fully glued onto the contact surfaces, as shown in the figure. The glue to be used can safely provide a shear strength of 140 psi. Determine the smallest allowable length L that can be used for the splice plates for an applied load of P = 20,000 lb. Note that a gap of a = 0.8 in. is required between boards (1) and (2).
A simply supported beam has a maximum moment equal to 20 KN.m. The beam has a width of 200 mm and a depth of 250 mm and is made up of 80% grade Narra. What is the actual bending stress of the beam in MPa? Blank 1 (use two decimal places, no need for unit)\\ with complete solution
A beam cast monolithically with the slab thickness of 110 has a span of 4 m spaced at 6 m center to center. The width of the web is 300 mm and effective depth of 500 mm. It is reinforced on the tension side with 8-20 mm Φ rebars. Fc’ = 30 MPa fy = 310 MPa 1. Which gives the effective width of flange? a. 2000 mm b. 1500 mm c. 2500 mm d. 1000 mm 2. Which gives the depth of the compression stress block? a. 30.55 mm b. 32.56 mm c. 12.45 mm d. 42.14 mm
STRENGTH OF MATERIALS (NO EXPLANATION NEEDED. RATE WILL BE GIVEN) For the lap joint below, the maximum safe load P if the shearing stress in the rivets, (diameter of each rivet is 20 mm) is limited to 60 MPa is equal to?
A simply supported beam 4 m long is carrying a variable load of w = 0 KN/m at the left support and w = 15 KN/m at the right. The beam has a width of 200 mm and a depth of 250 mm and is made up of 80% grade Narra. Use dressed dimension by reducing its dimensions by 10 mm. What is the actual bending stress of the beam in MPa? Blank 1 (use two decimal places, no need for unit)
1) The crate weight W = 100 N and the coefficient of static friction at the surface is ? = 0.30. A force P is applied at an angle ? from the horizontal surface. A) Determine the value of ? to obtain the smallest possible value of P so that the crate is on the verge of moving. B) Determine the smallest value of P. C) Determine the normal reaction between the crate and the horizontal floor. Use method of joints or method of sections as much as possible
A cantilever of rectangular section is 70 mm wide and 250 mm deep at the fixed end andtapers uniformly to 75 mm wide and 100 deep at the free end. The projecting length is1800 mm, and there is a load of 1800 N at the free end. Calculate the deflection of thefree end and the maximum bending stress. Take E = 14000 N/mm2. The cantilever is madeof timber.
A simply supported beam has a maximum moment equal to 25 KN.m. The beam has a width of 200 mm and a depth of 250 mm and is made up of 80% grade Narra. Use dressed dimension by reducing its dimensions by 10 mm. What is the actual bending stress of the beam in MPa? Blank 1 (use two decimal places)
b. A steel tape is 30m long under a standard pull of 6kg with a constant cross-sectional area of 0.05cm2 . If the normal tension applied to make the tape equal to its nominal length when supported only at the end points, that is the effect of sag will be eliminated by the elongation of the tape due to the application of this load is equal to 16kg. Determine the unit weight of the tape. Modulus of elasticity of tape is 2x106 kg/cm2 .