(d) A generator spins at 3600 rpm. Convert that rotational speed to units of rev/s. (e) A generator spins at 3600 rpm with a torque of 200 N m. In SI units what is the power? (f) An automobile engine produces 94 kW at 6300 rpm. In SI units, what is the torque? (g) An automobile engine produces 221 lb ft of torque at 1800 rpm. In Hp, how much power does this engine produce?

(d) A generator spins at 3600 rpm. Convert that rotational speed to units of rev/s. (e) A generator spins at 3600 rpm with a torque of 200 N m. In SI units what is the power? (f) An automobile engine produces 94 kW at 6300 rpm. In SI units, what is the torque? (g) An automobile engine produces 221 lb ft of torque at 1800 rpm. In Hp, how much power does this engine produce?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

What is the differential relation between displacement, velocity and acceleration?
An electric motor is used to drive the shaft of a small water pump. During a performance test, the torque on the motor shaft is found to be 5.886 N•m when the motor is drawing 763.54 W of electrical power. What is the rotational speed of the shaft in rpm?
What are the SI and U.S. Customary units for energy?
A parent exerts a torque on a merry-go-round at a park. The torque has a magnitude given by τ = 2.5θ2 + 11.0θ − 13.5, where the torque has units of newton meters when θ is in units of radians. (a) How much work is performed by the torque as the merry-go-round rotates through 1.50 revolutions, beginning at θi = 0? (answer in joules)(b) If it takes the merry-go-round 8.40 s to go through the 1.50 revolutions, what is the power transferred by the parent to the ride? (Enter the average power over 8.40 s.) (answer in Watts)
1) An electric motor’s torque is a function of the speed at which it rotates. Many brushed AC motors have a linear toque curve as shown below. If the power output of the motor is equal to the torque (T) multiplied by the rotational speed in rad/s (w), what is the maximum power you can get out of the motor if the stall torque (Tstall) is 0.001 Nm and the no load speed (wno load) of 10,500 RPM? Give answer in Watts.
In your own words, explain why the internal combustion engine made by Etienne Lenoir is the most significant event or invention made that contributed greatly to the development of traffic and transportation?
Determine the torque needed to bring a turbine whose moment of inertia of 60 slugs-ft² to rest in 1.2 sec from an initial speed of 764 rpm. The correct answer is 400 lb-ft.
What is the SI unit of acceleration due to gravity?
A wind turbine has the maximum power output at the rated speed of 12 m/s and a rotor diameter of 82 meters. The cut-in and cut-out speeds for this type of wind turbine are 4 m/s and 23 m/s, respectively. The table below shows the annual wind data near a potential site for setting up a wind farm using this type of wind turbine and the power coefficient of the wind turbine at the specific wind speed. The air density is 1.22 kg/m3. (a). What is the maximum power output of this wind turbine, assuming Betz limit? (b). What is the average power output if the wind turbine is installed at this site?. (c). What is the capacity factor of the wind turbine at this site? (d). If a wind farm consisting of 100 such wind turbines is built at the site, how much energy does this wind farm generate in a year (in the unit of kWh)? (e). Is this a good site for using this particular type of wind turbine?
Q1: what is the required force to move a car (1300 kg) from rest to 80 m (with a 20 m/sec)?
Please indicate the given, assumption and illustration. A Jet plane having a wing area of 20 m2 and weighing 25 kN flies at 950 km/hr speed. The engine develops 8,500 kW and has a mechanical efficiency of 9%. With the specific weight of air at 12 N/m3, determine the following: A) The Coefficient of Lift (CL). B) The Coefficient of Drag (CD).
Question 03: Discuss with the help of an examplehow is a flywheel able to store energy. Also, compare solid and hollow flywheel, which one will be more effective and why?