Can you please provide a details explanation and solution for this question? also please provide the answer for the question part d Question 2:Consider the system shown in the figure below. The frames have 8,000 bits, ACKS arenegligible in size, and the frame processing time is negligible at intermediate nodes. Thespeed of light in the fiber is 200,000 Km/sec.40 Kbps0.5 sec RTTWirelessdedidade0000000000010 Mbps100 KmFiber40 Kbps0.5 sec RTTWirelessABa) Assume that the frame transmission is error-free. Find the effective data throughput fromA to B when each wireless link uses Stop and Wait.Hint: The effective data throughput through the system is equal to that of the bottleneck link.b) Repeat the calculation assuming now that Stop and Wait is used on the complete pathbetween A and B.Assume for questions c and d that the wireless links each have a BER of 1×10-5, the ACK transmissions are error free, and the fiber link is error free.Note: when the wireless links are not error free, the achievable throughput drops to(1-FER) multiplied by the error free effective data throughput of the system, where FER is the frame error rate.c) Find the Frame Error Rate (FER), then find the effective data throughput from A to B when each wireless link uses Stop and Wait.d) When Stop and Wait is used on the complete path between A and B, the Frame is error free if there is no error during the first wireless transmission and there is no error during the second wireless transmission.Find the Frame Error Rate FER in this case, then find the effective data throughput from A to B assuming now that Stop and Wait is used on the complete path between A and B.

For T1: Frame size = 8000 bits Link bandwidth = 40 Mbps RTT = 0.5 For T2: Frame size =…

d) When Stop and Wait is used on the complete path between A and B, the Frame is error free if there is no error during the first wireless transmission and there is no error during the second wireless transmission. Find the Frame Error Rate FER in this case, then find the effective data throughput from A to B assuming now that Stop and Wait is used on the complete path between A and B.

d) When Stop and Wait is used on the complete path between A and B, the Frame is error free if there is no error during the first wireless transmission and there is no error during the second wireless transmission. Find the Frame Error Rate FER in this case, then find the effective data throughput from A to B assuming now that Stop and Wait is used on the complete path between A and B.

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter8: Data And Network Communication Technology

Section: Chapter Questions

Problem 2RP

See similar textbooks

Similar questions

Que.a) Consider a CSMA/CD network that transmits data at a rate of 400 x 106 bits per second. The maximum signal propagation time from one node to another node is 20 microseconds. The minimum size of a frame in the network is(. bytes).
Please check my answer and correct the part which is need to be foxed.And provide justification for the answer. a) The transmission time of a frame can be calculated as follows: Propagation delay (Tp) = distance/speed = 5km / 200000 km/s = 0.0025ms Transmission time (Tt) = frame size/bandwidth = 10000 * 8bits / (1Mbps * 10 ^ 6) = 0.008sec = 8ms Total time for transmission = 2 * Tp + Tt(since the frame has to travel from A to D and then D to A) = 2 * 0.0025ms + 8ms = 0.005ms + 8ms = 8.005ms The transmission time of the frame from A to D is 8.005 ms. b) The efficiency of the CSMA/CD protocol is given by the formula: Tt is the transmission time of a frame C is the number of collisions, Tp is the propagation time of a signal from one end of the segment to the other. Efficiency = Tt / (C * 2 * Tp + Tt + Tp) Assuming that there are no other stations transmitting or attempting to transmit on the segment, the transmission from A to D will succeed without collisions. Therefore,…
Four channels, two with a bit rate of 120kbps and two with a bit rate of 880kbps, are to be multiplexed using multiple-slot TDM with no synchronization bits.Answer the following questions: a. What is the size of a frame in bits? b. What is the frame rate? c. What is the duration of a frame? d. What is the data rate?
8. A pure ALOHA network transmits 200-bit frames on a shared channel of 200 kbps.What is the throughput if the system (all stations together) produces?a. 1000 frames per second?b. 500 frames per second?c. 250 frames per second?
Consider a full-duplex 512 kbps link with length 36,000Km connecting two hosts. The data frames carry a useful payload of size 6000 bits. Assume that both ACK and data frames have 400 bits of header information, and that ACK frames carry no data. The propagation speed along this link is 3×108 m/sec. a) What is the RTT on this link? b) What is the effective useful data throughput, in kbps, when using Stop-and-Wait?
Q. 2. (b) Suppose Robi has 32 voice channels, each of 60 Mbps. They use synchronous TDM to multiplex these channels. If two characters at a time is multiplexed (two characters in each output slot), answer the following questions: i) What is the size of an output frame in bits? ii) What is the output frame rate? iii) What is the duration of an output frame? iv) What is the output data rate? v) Input bit duration?
1. Suppose, there are two channels to multiplex, one bits from each source and use TDM with 180Kbps and 190Kbps. Pulse stuffing is allowed if requires. What is the size of a frame in bits? (a) 1(b) 2(c) 4(d) Not available 2. Which can not be an implementation area of FDM?* (a) Cable TV (b) FM Radio Broadcasting (c) First generation cell phones (d)Air band radio
A distant planet is about 9 x 1010 metres from the surface of the Earth. What is the channel utilisation of a point-to-point connection that operates at 64 megabits per second and uses a stop-and-wait protocol for frame transmission? Let's say that the speed of light is 3 108 metres per second, and that the frame size is 32 kilobytes.
Earth to a distant planet is 9 x 10^10 m. A 64 Mbps point-to-point link using a stop-and-wait protocol for frame transfer has what channel utilization? Assume 32 KB frame size and 3 × 10^8 m/s light speed.
Consider a CSMA/CD with frame size is 20 KB and transmission rate is 10 Kbps, then maximum length of the cable (km) required, if signal speed is 15 km/sec.
Don't copy from Chegg or Bartleby they are wrong solutions If the maximum transfer unit i.e. maximum Frame Size, for the considered Physical layer technology 80 bytes then what is the maximum frame rate for the case considered? Suggest an appropriate Frame size, slot size, then the frame rate and bit-rate for the designed scheme
A planet located far from Earth is around 9 x 1010 meters away. If a stop-and-wait protocol is employed for frame transmission on a 64 Mbps point-to-point link, what is the channel utilization? Assume that the speed of light is 3 108 m/s and that the frame size is 32 KB.