Data sheet below shows design parameters for a Common Source FET Transistor amplifier.VDD = 12V , VD = 0.75 VDD , VG = 0.5 VDD , Cin = Cout = 5muF , K = 1mAV-2 , VTN = 1V , R2 = 10k and ID = 2mA Q. At DC condition,design the circuit by calculating values for VG,R1,RD,VGS,RS and gm of the FET amplifier (show all the calculated steps involved). Propose and draw the DC circuit from the calculated values.

Data sheet below shows design parameters for a Common Source FET Transistor amplifier.VDD = 12V , VD = 0.75 VDD , VG = 0.5 VDD , Cin = Cout = 5muF , K = 1mAV-2 , VTN = 1V , R2 = 10k and ID = 2mA Q. At DC condition,design the circuit by calculating values for VG,R1,RD,VGS,RS and gm of the FET amplifier (show all the calculated steps involved). Propose and draw the DC circuit from the calculated values.

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter25: Television, Telephone, And Low-voltage Signal Systems

Section25.1: Television Circuit

Problem 5R: From a cost standpoint, which system is more economical to install: a master amplifier distribution...

See similar textbooks

Similar questions

For the circuit in the figure below, consider rd = 100kΩ and determine the values of: a) VGS, VDS, ID b) RIN, ROUT c) gm and AV gain
In the common-emitter amplifier circuit shown in the figure, Vcc=9V, R1=27kΩ, R2=15kΩ, RE=1.2kΩ and RC=2.2kΩ. The transistor has β=100.a-) If Rsig=10kΩ and RL=2kΩ, calculate the IE value of the amplifier.b-) For small signal analysis of the transistor, find the value of Rin by deriving the π-modelc-) Calculate vo/vsig and io/ii.
Consider a voltage-divider configuration of n-channel enhancement-type MOSFET where R1 = 12 MΩ, R2 = 7 MΩ, RD = 3 kΩ, RS = 1 kΩ. The MOSFET has a threshold voltage VGS(Th) = 3V, and one example point on the transfer characteristics curve is VGS(on) = 6V, ID(on) = 5 mA. Determine VGSQ, IDQ, Vs, VD, VDS assuming VDD = ( 80 ÷ 10 ) +20 V
For the MOSFET amplifier, given VDD = VSS= 8V, Rsig = 2Kohm, R3=3Kohm, Kn =K’n(W/L)= 0.5 mA/V2, Vtn= 1.2V, λ ≅ 0, Q point (0.8mA, 2.5V).Determine RD in Kohm
The dc bias circuit for a common emitter amplifier is shown in the figure. In the circuit, Vcc=15v,RB1=20k Ω,RB2=100k Ω,Rc=5.1k Ω,and RE1=1k Ω, Assume that when the transistor is on, the voltage drop from base to emitter VBE=0.7v. Also assume that β= ∞, which implies that the base current can be considered zero (IB=0) in your calculations. Solve for the base voltage VB. Solve for the emitter voltage VE. Solve for the emitter current IB. Solve for the collector current IC
Enclosed figure has common gate amplified circuit designed with MOS transistor. Following values are given for circuit:Vdd = 15V RL = 9KΩ Is = 2mA.Transistor Vth = 1V, Kn = ½.µ.Cox.W/L = 2mA / v²,λ= 0 and Vt = 25 mV. Draw DC model of circuit. Calculate the RD value required to have VDSQ = 11V for the transistor. Please calculate gm ve ro values for transistor. Draw the small signal equivalent circuit of the circuit and calculate the AV = VO / Vin voltage gain.
A common emitter amplifier as shown in Figure Q2 has the following parameters, β = 100, R1= 33K, R2 = 10K, RC = 3K3, RE = 1K, ro =  and VBE = 0.7 V.State all assumptions made.i. Check whether βRE>>10R2 is satisfiedii. Use the appropriate approach of analysis to determine the Quiescent point; IBQ,ICQ and VCEQ.iii. Draw the small signal equivalent circuit. Determine input impedance, Zin, outputimpedance, Zout, and the voltage gain, AV, if RL=20kΩ.
In the circuit given in the figure, what is the voltage gain (Av) of the circuit when = 100, r0 = 40 kΩ, RB = 360 kΩ, RC = 3.3 kΩ, RE = 220 Ω, Rs = 15 kΩ and RL = 166 kΩ?NOTE-1: The output impedance r0 of the transistor will be taken into the calculations.NOTE-2: Capacitors are negligible at mid-band frequency.
Coonsider the common emitter amplifier shown in figure below. Assume a β of 100, VBE = 0.7V, VT = 25mA and VA = 100V. Draw an equivalent DC model and determine the rπ, transconductance (gm) and ro. Draw an equaivalent AC model using the small-signal model Find an expression for vbe and vo in terms of the input voltage
Find Ic, Ib, Vce, Vc, Vb, VeVrc,Vrb for all the CE amplifier circuit Show the solutions using kvl Draw the DC load line of each circuits
a. In AC, how are the capacitors treated? b. In AC, how are DC sources treated? c. What is the amplifier configuration of Figure 4? d. What is the expected phase shift of the sinusoidal input at the output side? e. What is Zi across RG, the gate resistor? f. It is the IC in its smallest form. g. The most commonly used metal as interconnect of the chip to external peipheral. h. How is pin 1 of the chip determined? i. An IC package similar to a DIP but with the pins bent outward. j. Which sensors are packed as IC?
In the circuit in the figure, Vcc = 18 V and RL = 2.2 kΩ, while C1 = C2 = CE = 0.1 μF. It is also known that for parasitic and wiring capacitors, Cwi = 15 pF, Cwo = 21 pF, Cbc = 27 pF, Cbe = 887 pF and Cce = 25 pF. Accordingly, what is the bandwidth of the system? NOTE-1: The output impedance of the transistor r0 will be neglected in the calculations. NOTE-2: The high frequency dependence of hfe, β, will be neglected.