Dechlorination contact tank (Wastewater Treatment) An activated sludge plant has a design flow (average daily flow) of 11 MGD. Determine dimensions of dechlorination tank. The design parameters: use 1 tank. detention time = 30 sec, depth = 10 ft, rectangular tank: L = 4 W. use maximum hourly flow (3 * Average design flow)

Dechlorination contact tank (Wastewater Treatment) An activated sludge plant has a design flow (average daily flow) of 11 MGD. Determine dimensions of dechlorination tank. The design parameters: use 1 tank. detention time = 30 sec, depth = 10 ft, rectangular tank: L = 4 W. use maximum hourly flow (3 * Average design flow)

Sustainable Energy

2nd Edition

ISBN:9781337551663

Author:DUNLAP, Richard A.

Publisher:DUNLAP, Richard A.

Chapter14: Ocean Thermal Energy Conversion And Ocean Salinity Gradient Energy

Section: Chapter Questions

Problem 14P

See similar textbooks

Similar questions

It was decided to design waste water collection system. The flow rate is 75000 L/d. A circular concrete pipe was constructed to convey waste water to small waste water treatment plant. Determine the flow velocity, pipe diameter and depth of water in the pipe.
Q#2 a) A treatment unit is 7.0m wide, 25m long and has a depth of 3.5m. If the wastewater flow rate through the tank is (18300) gallons per day. Calculate: 1. Hydraulic detention time 2. Surface loading rate
Water at T� = 25∘C∘C is drawn from an underground detention tank and discharged into a drain using a 9-mm-long pipe and pump (Figure 1). The pipe has a diameter of 100 mmmm and a friction factor of f� = 0.02. The atmospheric pressure is 101.3 kPakPa. The velocity through the pipe is 4 m/sm/s and hℎ = 2 mm. Neglect minor losses. Determine the available NPSH. Express your answer using three significant figures. Determine the required NPSH. Use the pump performance curves shown above. Express your answer using two significant figures.
Q- What is the surface area (m2) of settling tank used for design discharge of 1.5 m3/s? (Assume design overflow rate for tank as 40 m3/m2/day.)
Determine the flow in each of the pipes shown in the figure. Assume f=0.02 for all pipes. Problem 7-66 with the following conditions: - roughness coefficient for all pipes = 0.05 - elevation B = 100 m
A conventional activated-sludge system treats 11,000 m3/day of wastewaterin an aeration tank with a volume of 3400 m3. The BOD after primary clarification is 180mg/l. Given the operation conditions below, calculate the sludge residence timeMLVSS in the rector = 2,100 mg/lMLSS = (1.25)*MLVSSQw = 160 m3/daySVI = 125 mL/g (Ans. SRT = 7.0 days)
Three pipes 1, 2, 3 are connected as shown. If the total discharge forthe system is 610 L/s and the friction factor f is equal for all pipes,then:What is the flow rate (in L/s) in pipe 3?
a. Calculate the pump head b. Plot the EGL and HGL for the system
The discharge through a concrete pipe of 1 ft diameter and 3000 ft length is 1.0 cfs. What is the head loss (hr) if the water temperature is 60°F? Apply the Darcy- Weisbach equation
Design a septic tank for a small restaurant with 10 employees and averaging 220 customers per day and assuming 75% toilet usage for the customers. The estimated sewage flow rate for this restaurant is 7 gallons/person/day. The septic tank capacity is computed as 1.5 of the estimated flow rates. Determine the required dimensions of the digestive chamber and the leaching chamber. Assume 1.8 m liquid depth.
Assume that DLSUD lake is 100m2 and its average height is 5ft. Wastewater that flows into the lake are the following: Food square kitchen waste 7 m3/sec; Total Dissolved Solids (TDS) is 25,000 mg/L which operates 8hrs per day CIH 5m3 /hr kitchen waste; TDS is 20mg/L which operates 4hrs per day PCH 20m3 /day diluted laboratory waste ; TDS = 40mg/L (1)Determine the volumetric flow rate of the lake water can still accommodate prior to rainfall.
A sprinkler head has a discharge rate of 22.5 gal./min and a coefficient K = 5.65. What pressure is required at the sprinkler head?