defeat Water is pumped from a lake to a storage tank 80 m above at a rate of 0.005 m³/s. If the GL pump-motor efficiency is 75%, and the irreversible head loss is 15 m. a) Find the consumed electric power by the pump. b) Find the pressure difference across the pump. 20 80 m ZT² Pump Storage tank 20 Zz Z

defeat Water is pumped from a lake to a storage tank 80 m above at a rate of 0.005 m³/s. If the GL pump-motor efficiency is 75%, and the irreversible head loss is 15 m. a) Find the consumed electric power by the pump. b) Find the pressure difference across the pump. 20 80 m ZT² Pump Storage tank 20 Zz Z

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter13: Energy And Power

Section: Chapter Questions

Problem 3P: An elevator has a rated capacity of 2200 lb. It can transport people at the rated capacity between...

See similar textbooks

Similar questions

If the flow of 0.10 m3/s of water (mu = 1.31 x 10-3 Pa.s) is to be maintained in the system shown, what power must be added to the water by the pump? The pipe is made of steel and is 15 cm in diameter. Neglect minor losses. TV
A pump is installed in a pipe system, where at the suction side 1.0 m below the pump, an open manometer reads a vacuum of 20 cm of mercury. The pipw is 10 cm in diameter and the flow is 35 L/s of water. Find the total energy at the location of the manometr, relative to a datu, through the pump.CHOICES a.2.74 m. b.-4.67 m. c.2.56 m. d.-2.72 m.
Water from an open tank elevated 5m above ground is allowed to flow down to a pump. From the pump, it flows horizontally through 100m of piping, and out into the atmosphere. Assume a pump efficiency of 55%, and friction is negligible in the pump suction line. If there are 2 standard elbows and one wide open gate valve in the discharge line, Calculate for a) all friction losses in the system b) the power requirement of the pump if it is to maintain 0.8 m3 / min of flow.
For water supply of a town, water is pumped from a river 4km away into a reservoir. The maximum level difference of river and reservoir is 20m. Town population is 50,000 and per capita water demand is 120 lpcd. If the pumps operate for a total of 8hrs and pump efficiency is 60%, calculate pump B.H.P Assume friction factor as 0.0075 and pipe velocity as 2m/s and maximum daily demand as 1.6 times avg. daily demand.
Water from the reservoir is pumped over hill through a 90 cm diameter pipe, and the pressure of 200 kPa is maintained at the summit, where the pipe is 90 cm above the reservoir.The flow is 1.40 m^3/s with a headloss of 3.0 m between the reservoir and summit. If the pump is 90% efficient, what is the input power furnished to the water in KW. CHOICES: a.1734 b.1923 c.1865 d.1954
pump discharges 1129.52 kg/min of water to a vertical tank (10ft dia by 15 ft height). Find the total time (in min) the tank will be 3/4 full.
A pump is used to raised water to a reservoir through 1000 m. long of 20 cm diameter with Cw of Hazen-William's Equation equal to 100. If the pipe is to be replaced with a new one having the same length but with a diameter of 25 cm and Cw= 120, determine the power save if the flow is to be maintained at 75liters per second. Draw the approximate EGL and HGL
9.The pump shown delivers 115 li/s of oil, sg = 0.84, toreservoir D at elevation 72 m. The energy lost in thesuction line is 3.2 J/N and in the discharge line is 7.6 J/N. a.Compute the total head added by the pump. b.How many kW does the pump supply the system? c.If the pump is 85% efficient, how much power does it need?
What is the required pump power (Pa) for the system below? The source reservoir is on the right side of the figure The outflow is released as a water jet to the atmosphere (on the left) Discharge rate is 0.11 m3/s Pipe total length is 180 m Pipe diameter is 0.2 m Friction factor (f) is 0.01 Minor losses are negligibleCHOOSE ONE: 25 KiloWatt 169 KiloWatt 269 KiloWatt 112 KiloWatt
A reservoir A with elevation 30m connected with a pump to rise the water into two reservoirs B and C 90m and 60 m respectively the amount of flow from J to B is equal 0.11 m/sec use the following data to determine the flow in each pipe and the power of the pump: LAJ 450 m, DaJ = 300 mm, LJB= 300 m, DJB = 200 m, Q JB = 0. m'/sec, LJc 600, D Jc = 150 mm,f (all Pipes) 0.02
Q2: Water is flow by arate = (v/( “7— /20) m¥/s , the water is still stable due to using a pump as shown in figure below. A pipe of rectangular cross sectional area of dimension (10 *20 ) cm is used to connect the two reservoir, friction factor for the pipes(£=0.02), if K value in the entrance and in the exit are 0.1 and 1 respectively. Calculate the pump power:- ElL15m Water EL10m Water = o cotanantwe *10 = 50 m——
Water (γwater = 9810 N/m3) drains from the reservoir higher to the bottom, both with constant levels, by a pipe with a diameter equal to 75 mm, passing a turbine to power generation. Knowing that the total load loss between sections (1) and (4) is equal to 2.0 m and where the flow rate is equal to 10 L/s; can determine: The power on the turbine shaft in kilowatts (kW), whereas the performance of the machine is 75%. Consider that V1 ≈ 0; V4 ≈ 0. If the static pressure in section (3) is known, equal to 200 kPa, determine the piezometric (CP) and the total energy in this section. Also calculate the CP and the total energy in (2). Data: h1 = 10 m; h2 = 10 m; h3 = 4 m.