Define flow separations both statement and formulations around and along an airfoil in flow direction. Depending on the angle of attack, how can you retard/delay/diminish/control/postpone/decrease the flow seperation on airfoil? Write down at least five methots, briefly describe and draw schematic figures for each method.

Define flow separations both statement and formulations around and along an airfoil in flow direction. Depending on the angle of attack, how can you retard/delay/diminish/control/postpone/decrease the flow seperation on airfoil? Write down at least five methots, briefly describe and draw schematic figures for each method.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.30P: Air at 1000C flows at an inlet velocity of 2 m/s between two parallel flat plates spaced 1 cm apart....

See similar textbooks

Similar questions

Air at 20C flows at 1 m/s between two parallel flat plates spaced 5 cm apart. Estimate the distance from the entrance to the point at which the hydrodynamic boundary layers meet.
Evaluate the Nusselt number for flow over a sphere for the following conditions: D=0.15m,k=0.2W/mK, hc=102W/m2K.
The lift curve for the 4 digit NACA 2421 airfoil is shown in the Figure. Consider a wing with AR = 8, sweep ? = 15 ???, and airplane flies at the Mach number equal to 0.3. The Oswald efficiency span number ?1 = 0.95 Calculate the lift slope for the finite wing. Clearly show the formula and explanations in the solution.
Air flows at Ma = 2.5 past a half-wedge airfoil whoseangles are 4°, as in Fig. Compute the lift and dragcoefficient at α equal to (a) 0° and (b) 6°.
simple answer a)What is an adverse pressure gradient, and where does it occur on an airfoil (Show that onan airfoil using a free hand sketch)? b) Why do golf balls have dimples? Hint: Support your answer by a sketch
Consider an infinite wing with a NACA 1412 airfoil section and a chord length of 3 ft. The wing is at an angle of attack of 5° in an airflow velocity of 100 ft/s at standard sea-level conditions. Calculate the Reynold’s number, lift, drag, and moment about the quarter-chord per unit span. Cl = 0.67, Cmc/4 = -0.025 and Cd = 0.007Detailed solution pls
The so-called Rocket Man, Yves Rossy, fl ew across the Alps in2008, wearing a rocket-propelled wing-suit with the followingdata: thrust = 200 lbf, altitude = 8,200 ft, and wingspan = 8 ft(http://en.wikipedia.org/wiki/Yves_Rossy). Further assume awing area of 12 ft2, total weight of 280 lbf, CDq = 0.08 for thewing, and a drag area of 1.7 ft2 for Rocket Man. Estimate themaximum velocity possible for this condition, in mi/h.
Air at 20°C and 1 atm flows at 3 m/s past a sharp flat plate2 m wide and 1 m long. (a) What is the wall shear stress atthe end of the plate? (b) What is the air velocity at a point4.5 mm normal to the end of the plate? (c) What is the totalfriction drag on the plate?
A) How does an airfoil generate lift? Hint: Support your answer by a sketch. B) Compare between the laminar and turbulent boundary layers? Hint: Show their velocity profiles in a sketch and highlight the main differences. C) Which boundary layer is preferable when it comes to separation? Why? D) Why do golf balls have dimples? Hint: Support your answer by a sketch. E) What will happen to the critical Reynolds number for each of the following cases: i- Pressure gradient is made more adverse. ii- Surface roughness is decreased. iii-Free-stream turbulence is increased.
a)What is the impact of increasing Reynolds number on skin friction and pressure drags over an airfoil? What can be happened for separation in this case? b) What is an adverse pressure gradient and where does it occur on an airfoil (show that on a sketch)? c) Why lift-to-drag ratio is an important parameter for an aircraft? d)How can changing in altitude affect the aircraft power required, PR? Show thatmathematically and graphically?
Consider an aircraft that has the maximum takeoff weight (MTOW) of 19500kg. The aircraft is required to cruise at 10500 m at Mach 0.6. a) Analysis and sizing of the wing (lift and drag calculations, aerofoil selection etc.) Wing area: 118588.94mm^2
A straight-tapered flying-wing aircraft has the following characteristics: span, 20 ft; area, 100 ft2 ; root chord, 6 ft; tip chord, 4 ft; leading-edge sweep angle, 40 deg; sweep angle of line of maximum thickness, 24 deg; and Airfoil NACA 2412. Determine the wing's lift-curve slope and induced drag k value. Assume the flight Mach number is 0.25 in standard sea-level conditions.