Define holding current and latching current.

Q: Electronic balances must be ideally located in a room with continuous ventilation and natural flow…

A: This problem is from electronic balance.  The statement is true.

Q: ) State TWO (2) needs for the protection system under the abnormal operating condition.

A: The explanation is as follows.

Q: When does current flow in a circuit? What makes current flow in a circuit?

A: Current is the flow of electrons in an circuits per seconds. Now for electrons to flow the cir uit…

Q: In induction type energy meter, Recording system consists of a set of dials…

A: Induction type energy meter

Q: Which is a better source of information, the power supply or the DMM? Why?

A:

Q: 1.Compare Latching and Holding Current Ratio                      note::::::::: only short answer…

A: Latching current is associated with turn-on process of SCR. Holding current is associated with…

Q: How much current is flowing through the circuit?

A: from the previous solution, VD1=5 VVD2=-1.7 V The simplified circuit is drawn below:

Q: During electric interruption, what is being lose? Is it the voltage source, electric current or…

A: Electric interruption                  In Computer systems and other electronic devices that…

Q: Write a verilog and testbench for up down counter

A: Write a verilog and testbench for up down counter' Here we use High for Up Counter and Low for Down…

Q: List the different Wire Gauge and its uses. Note: Typical wires at home.

A: The wire gauge is used to measure the diameter of the wire. The measure of electric flow the wire…

Q: What should be the K range for the following system to be stable?

A: The solution can be achieved as follows.

Q: 2) Under which conditions do over voltages and under voltages occur?

A: Conditions for over voltage is lighting impulse or switching impulse. Eg:- lightning strikes on…

Q: 8. What is the purpose of a lockout-tagout procedure? 9. List protective equipment.     10. When…

A: (8) Purpose of a Lockout - tagout procedure - This procedure is used to protect the employee from…

Q: ) Why power electronics iS necued?

A: As per Bartleby guidelines we are allowed to solve only one question, please ask the rest again. The…

Q: Explain how this system works

A:

Q: what is fuse, outlet, switch and plug?

A:

Q: To test a voltage, should the circuit be energized?

A: To ensure the safety of the personnel carrying out the electrical repairing work, the circuit or…

Q: 7. What is the effect of potentiometer when short-circuited?

A: A potentiometer is a variable resistor and in this the resistance is manually assorted to control…

Q: A cable has a VSWR of 10. If the minimum voltage along the cable is 20 volts, what is the maximum…

A:

Q: What happen if you followed the basic electrical rules?

A: If we followed the basic electrical rules following circumstances would not happen: - Contact with…

Q: What screw size is use to secure a lighting outlet ?

A:

Q: Define Latching ad holding current in short

A: Latching current is minimum current flows from anode to cathode terminal of the SCR and the SCR will…

Q: hich type of resistivity tool can be used in a well which has been drilled with oil ist all factors…

A: As per Bartleby guidelines I can not give answer of more than three subparts of the question.

Q: Explain Coordination between fuses and over current protective devices.

A: Overcurrent is current that excels the ampere rating of conductors, devices, or equipment under the…

Q: (b) Explain what is power system protection and why is it important?

A:

Q: 5. Explain the advantages and disadvantages of various types of grounding and indicate where each…

A: The system earthing refers to the earthing of the transformer and generator's neutral points. A…

Q: This discussion relates to Bonding. Whys is bonding of the conduit necessary when using reducing…

A: Bonding becomes necessary to reduce the risk of shock and it also provides a low impedance path to…

Q: 1. Which statement is true for latching current? a. It is related to turn off process of the device.…

A: Since you have posted the multiple questions so we are supposed to answer 1st questions only.

Q: Explain how the circuit works

A:

Q: What is the dimension of voltage ?

A:

Q: Classify the following systems to open or closed-loopP control system: Conly 5) 1- Human Arm 2-…

A:

Q: Draw the primary protection zones for each element of the system in the figure shown.

A: We have to draw the primary protection zones for the given power system shown below:

Q: What is Latching current and holding current?

A: Latching current: Latching current is the minimum amount of the current which is flowing from anode…

Q: A switch is also an electrical conductor that serves as a mechanism to conveniently "open or close"…

A:

Q: THE TYPE OF WIRES AND WIRE GAUGES?

A: A wire is a single flexible strand of a metal, made up of materials which are good conductors of…

Q: Explain in detail what ring counters are and how they are employed.

A: given  we need to give a detailed explanation about ring counters and their applications

Q: What do you mean by stability of the system when the circuit open

A: Open-loop stability : Open loop is one-way system with no way to change how the machine works. A…

Q: Household refrigerators have arrays or coils of tubing on the outside, usually at the back or…

A: Household refrigerators have arrays or coils of tubing on the outside, usually at the back or…

Q: switch

A:

Q: Compare Latching and Holding Current Ratio

A:

Q: What is a VOLTAGE DROP?

A: Dear student please find the attachment.

Q: Question 4. Explain why grounding is important for the electrical safety of medical devices and how…

A: The obstruction that a current faces in its flow is called the impedance of that path. The currents…

Q: What is the current and voltage ?

A:

Q: Couses EEP Draw a WIRING DIAGRAM for wiring Two Way - One Gang Switches (51 and S2) to control…

A:

Q: Whenever closed conduits are used in a hydroelectric power plant, is/are used to limit the abnormal…

A: The surge tank is used to limit abnormal pressure in the conduit, whenever closed pipes are used in…

Latches and Flip Flop

Just like logic gates, the latches and flip-flops are the important elements of an electronic circuit. The logic gates form the important part of combinatorial circuits, while the latches and flip-flops form the essential part of a sequential circuit. Sequential circuits form the important concept of automata theory in electronics and electrical engineering, these circuits are a kind of logic circuit whose output depends on both present input and past inputs, that is, the input history.