5.A cylinder of 40 cm length and 10 cm diameter rotates about a vertical axisinside a fixed cylindrical tube of 105 mm diameter, and 0.4 m length. If thespace between the tube and the cylinder is filled with liquid of dynamicviscosity of 0.2 N.s/m2. Determine the external torque that led the cylinderto rotate by speed of 700 rev. /min.105 mmSolution100 mm40 cm

Answered: Image /qna-images/answer/185e0eeb-6e69-44fc-be18-68d61dedfb15.jpg

Answered: der of 40 fixed cyl etween the y of 0.2…

Engineering

Mechanical Engineering

der of 40 fixed cyl etween the y of 0.2 N e by speed

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q4: The hydraulic lift in a car repair shop has an output diameter of 30 cm and is to lift cars up to 2000 kg. Determine the fluid gage pressure that must be maintained in the reservoir.
To what height will 68˚F ethyl alcohol rise in a 0.005 in internal diameter glass capillary tube? The density of the alcohol is 49 lbm/ft3 note ? = 0.00156 ???/ ?? and ? = 0°.
A 1.2-m-diameter, 3-m-high sealed vertical cylinder is completely filled with gasoline whose density is 740 kg/m3. The tank is now rotated about its vertical axis at a rate of 70 rpm. Determine (a) the difference between the pressures at the centers of the bottom and top surfaces and (b) the difference between the pressures at the center and the edge of the bottom surface.
An open tank 5m long, 2m deep and 3 m wide contains oil of relative density 0.9 to a depth of 0.9 m. If the tank is accelerated along its length on a horizontal track at a constant value of 3 m/s2 , determine: (i) The new positon of the oil surface. (ii) The pressures at the bottom of the tank at the front and rear edges. (iii) The amount of spill if the tank is given a horizontal acceleration of 4.5 m/s2 instead of 3 m/s2 .
Assume an ideal fluid with mass density of 900kg/cu.m. The pressure and velocity at section 1 are 100kPa and 10 m/s, respectively. The velocity at section 2is 20 m/s. (a) Determine the reading on the manometer.(b) If the downstream piezometer was replaced with aPitot tube, what would be the manometer reading?Comment on the practicality of these arrangements.
The bottom quarter of a vertical cylindrical tank of total height 0.4 m and diameter 0.3 m is filled with a liquid (SG > 1, like glycerin) and the rest with water, as shown in the figure. The tank is now rotated about its vertical axis at a constant angular speed of ω. Determine (a) the value of the angular speed when the point P on the axis at the liquid-liquid interface touches the bottom of the tank and (b) the amount of water that would be spilled out at this angular speed.
two vertical parallel glass plates 0.1 mm apart are partially immersed in water. Considering that the water does not reach the upper edges of the sheets and that the liquid completely wets the glass, determine: a) the height that rises in the flat capillary, b) the attractive force between the plates. Consider the width of the sheet l=12cm and density y=72.8*10^-3 N/m
Determine the capillary action (rise or fall) of mercury in a capillary tube of diameter 1.5 mm. Surface tension is 0.514 N/m and contact angle is 140°.A. 7.87 mm rise C. 8.78 mm fallB. 8.78 mm rise D. 7.87 mm fall
The truck carries an open rectangular container that is 3.9m wide, 3.0m deep and 5.0m long, contains oil of density 811kg/m³ to a depth of 2.1m. If it has a constant acceleration of 6.9m/s². Determine the total force(in kN) acting at the rear wall of the container.
A cylindrical disk ofwood weighing 45.0 N and having adiameter of 30.0 cm floats on a cylinderof oil of density 0.850 g /cm3(Fig.). The cylinder of oilis 75.0 cm deep and has a diameterthe same as that of the wood.(a) What is the gauge pressure at thetop of the oil column? (b) Supposenow that someone puts a weightof 83.0 N on top of the wood, butno oil seeps around the edge of thewood. What is the change in pressureat (i) the bottom of the oil and(ii) halfway down in the oil?
A capillary tube is immersed vertically in a water container. Knowing that water starts to evaporate when the pressure drops below 3.5 kPa, determine the maximum capillary rise and tube diameter for this maximum-rise case. Take the contact angle at the inner wall of the tube to be 6° and the surface tension to be 1.00 N/m. Find the tube diameter for the maximum rise (in μm.)
A compressed air tank is designed to contain 50 standard cubic feet of air when filled to a gaugepressure of 200 atm at an ambient temperature of 70 F. Assume this is an air tank for scubadiving, and that the approximate shape of the tank is a cylinder with circular cross section. The interior volume of the tank is v=0.253 ft^3(a) If the interior length of the cylinder is 1 ft, what would be the inner diameter?(b) It is desired that the air tank be neutrally buoyant when empty. The density of aluminum is2700 kg/m3. If the tank is made of aluminum, what should be the wall thickness in order forit to be neutrally buoyant?