3. Derive a and b (shown to the right) for the S-N line from 103 to 10° cycles. Given:at N=10° cycles, S=f Sut•(f Sm)?Sea =At N=106 cycles,1(f SumS, = a Nºlogb =3Se- Low cycle-- High cycleFinite lifeInfinitelife10010°10'101010101010710Number of stress cycles, NFatigue strength S,. kpsi

Answered: Image /qna-images/answer/6855a172-c853-4eb6-9e1e-8e00c4107020.jpg

Answered: Derive a and b (shown to the right) for…

Derive a and b (shown to the right) for the S-N line from 10 to 10 cycles. Given: at N=10° cycles, Sp=f Sut a • At N=10 cycles, Se S; = a N° 1 log 3 - Low cycle -High cycle Finite life

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A steel shaft 3 m long is transmitting 1 MW at 240 rev/min. The working conditions to be satisfiedby the shaft are: (a) the shaft must not twist more than 0.02 radian on a length of 10 diameters.(b) the working stress must not exceed 60 MN/m2. If the modulus of rigidity of steel is 80 GN/m2. what is: (i) the diameter of the shaft required.(ii)the actual working stress. (iii) the angle of twist of the 3 m length.[Ans: 150 mm; 60 MN/m2 ; 0.030 rad]
60 degree F water flows through a horizontal turbine. The water speeds at the turbine inlet and the turbine outlet are identical. The water gage pressure at the turbine inlet is 46.4 psi while that at the outlet is 12.2 psi. Assume water frictional losses through the turbine are negligible. Deterimine the shaft work rate in ft*lb per slug of water passing through the turbine. Answer with a positive number if mechanical energy goes into the water and a negative number if mechanical energy comes out of the water as it passes through the turbine.
The connecting rod of a four stroke cycle Diesel engineis of circular section and of length 550 mm. The diameter and stroke of the cylinder are 150 mm and240 mm respectively. The maximum combustion pressure is 4.7 N/mm2. Determine the diameter ofthe rod to be used, for a factor of safety of 3 with a material having a yield point of 330 MPa.Find also the maximum bending stress in the connecting rod due to whipping action if the engine runsat 1000 r.p.m. The specific weight of the material is 7800 kg/m3. [Ans. 33.2 mm ; 48 MPa]
The values given for a radial plain bearing are:Shaft diameter = 40 mm, bearing width = 30 mm, Pem = 6 N / mm2, Radial force = 2 KN, Ty = 45 C, oil: ISO VG 15, bearing clearance = 35 µm, dynamic viscosity for given oil and temperature = 12 m Pa. sRequired:a) What is the working cycle of the shaft?b) Find the Sommerfeld number.
A compressor piston has a stroke of 380 mm and the clearance volume of 7% of thestroke volume. At the beginning of compression stroke the pressure of air is 0.99 barWhen the piston has travelled 260 m from the begining of the compression stroke thedelivery valves open and delivers air at 4 bar. Find the value of "n", iif the compressionfollows the law PVn = CA. 1.37B. 1.39C. 1.28D. 126
The shaft and the flange of a marine engine are to be designed for flange coupling, in which the flange is forged on the end of the shaft. The following particulars are to be considered in the design: Power of the engine=2.4 MW Speed of the engine 80 r.p.m Permissible shear stress in bolts and shaft = 60 MPa Number of bolts used =6 Pitch circle diameter of bolts=1.6* Dimeter of shaft Find 1.diameter of shaft; 2.diameter of bolts; 3.thickness of flange; and 4.diameter of flange. (25 degrea
The connection between an electric motor and a construction machine shaft is provided by means of a rigid coupling with flanges, through which the moment is transferred via the coupling flanges.The power of the electric motor is 35kw and the speed is 870rpm. The coupling flanges are connected with three bolts of quality 5.6 with a placement diameter of 40 mm.The surface pressure safety stress for bolts is 16 MPa. The contact length of the bolt with the coupling flange is 12 mm. The coefficient of friction on the flange surfaces is 0.14; the operating factor for the coupling is 0.8. The working conditions of the contact element, the material properties are very well known; since force and stress analyses can be performed with high accuracy,; question) Determine the bolt that should be used in the clutch from the table.
1. A LEV system has a centrifugal fan rotating at 714 rpm. The airflow is 6210 cfm, the fan total pressure is 4.07” w.g., and the brake horsepower is 3.12 hp. If the rotating speed is decreased to 620 rpm, what are the brake horsepower? a. 1.43 hp b. 2.04 hp c. 2.41 hp d. 2.67 hp 2.A LEV system has a centrifugal fan rotating at 714 rpm. The airflow is 6210 cfm, the fan total pressure is 4.07” w.g., and the brake horsepower is 3.12 hp. If the rotating speed is decreased to 620 rpm, what are the new value for fan total pressure? 4.15" w.g. 3.87" w.g. 3.07" w.g. 3.94" w.g.
Equation 6.16: εT = ln(li / l0)
Pls answer thank you! A turbine is connected to a generator by means of flange coupling that has a bolt circle diameter of 600 mm. The generator output is 80 MW, 60 hz and 95 percent efficiency. If there are 18 bolts, determine the force acting on each bolt.
An equation for determining the friction factor developed by Colebrook is 1/√f =-0.869 ln((ɛ/D)/3.7+2.523/(Re. √f)). Check the location of line ɛ/D=0.0002 on the Moody diagram with the equation above for a Reynolds number, Re is 10⁵.
ε0= 0.005B (hr-1Pa-1)=4.20E-34n=3.15 σ0 (Pa)= 550000000