Describe boring spacing and depth?

Q: Define Lateral movement

A: Lateral Movement: The movement of any body which is moving to any side of the body is known as…

Q: complete solution and drawing. if u can please add some explanation thankyou FN = 49 MN = 101…

A: To determine the internal loading as point E.   Following is the free body diagram of the given…

Q: Why is the Resident Project Representative required to submit sketches along with the Report of…

A: - A Resident Project Representative is a person who is assigned to a project to work along with the…

Q: Explain grid leveling.

A: LevelingLeveling is the method or procedure to determine the relative altitude of any point on the…

Q: In the plan below, shows a differential levelling from benchmark to another bench mark, along each…

A: 1. Compute the elevation of TP2? 2. Compute the elevation of BM2? 3. Compute the elevation of TP3 ?

Q: Please draw the steps in doing profile leveling using the date given. Please provide proper…

A: Given Data, Bm ---bench mark  Tp- Turning point  Bs -- Back sight  Is -- intermediate Sight…

Q: draw any plan using 3x1.5x2.4m

A:

Q: 23) Explain level parts and the procedures of setup with sketch.

A: Levelling or leveling is a branch of surveying, the object of which is to establish or verify or…

Q: Objectives, Conclusion (100 words) , and Recommendations

A: Traverse is a series of connected survey lines of known lengths and directions.Traversing refers to…

Q: How did the angle become 85 degrees on the one encircled with red pen below?

A: The sum of angles T a point on a straight line is 180°.

Q: Describe Source Correction Method.

A: Solution: The source correction method is the effective method that is used as effective methods to…

Q: Define Borings Spacing and Depth.

A: Borings should be placed at intervals not exceeding 100 feet and at the ends inside the existing…

Q: Give the coordinates for the following autocad drawing

A: The points are named as below

Q: To make a peg adjustment, the following notes were taken:     Wye level at 1 Wye level at 2 Rod…

A: Plane Surveying is that sort of looking over in which the mean surface of the earth is considered as…

Q: How does a plumbing contractor know what slope is required on sanitary piping installations?

A: The slope changes as the temperature changes in a sanitary installation.

Q: Name: - Section:- X 100 * 200 + 250 + 300 350 *400 x450 x350 +250 300 x 500 200 x400 150 500 Draw…

A: Contour interval = 50 m So, the difference between these levels should be 50m We will draw contours…

Q: What is tangent modulus?

A: The tangent modulus can be defined as it is the slope of a line tangent to the stress-strain curve…

Q: Level surface, Bubble line, Horizontal line, Level line, Line of collimation, Bench mark, Change…

A:

Q: Using neat sketches differentiate between true- datum or skidless instruments and Surface- datum or…

A:

Q: figure, Draw up a level book page and reduce the levels by the height of instrument method.

A:

Q: Why double roaded lines are used?

A: After the complete construction of roads, the markings on roads are done. The purpose of these…

Q: What perameters are used for Existing ground level ?

A: Solution: Ground level means the existing level of the site at any of the point. When earth filling…

Q: Q2: Draw front and side view projection for the following 36 12, 34

A: Given section: If you look at the given section from the front, the red coloured area will be…

Q: List the four types of sketches grouped by projection methods

A: The four types of sketches grouped by projection methods are listed below-

Q: Q24. Draw the plan, section and elevation of the given line diagram. W BED KITCHEN 2500x2500 D…

A:

Q: Define the standard penetration number ?

A: Standard Penetration Number is used in the standard penetration test which is used to determine the…

Q: What is the contour Interval?

A: To determine the contour interval from the given topographic map.   From the given map, the known…

Q: number shown is the R.L. of the land at the corner of the grid next to the number. DRAW AND LABEL…

A: Given:- grade = 0.5% To find:- label and draw contours at 1m INTERVALS

Q: Explain the method of traversing?

A: Solution: Traverse is a method used in the field of surveying that is used to control the networks.…

Q: To make a peg adjustment, the following notes were taken: Wye level at 1 wye level at 2 Rod reading…

A: Wye level at 1 ( midway between the PQ) The reading at P = 1.241m The reading at Q = 1.513m. As…

Q: Does the use of a CAD system eliminate the need for trial sketches and other preliminary placement…

A: CAD is the latest technology to design any form of structure. There are so many benefits of this…

Q: Draw a simple weir drawing plan (show side elevation and top view)

A: Weir is a hydraulic structure used for various purposes like storage, discharge measurements, silt…

Q: step by step procedure on doing this lab report (drawing/illustration) open compass traverse

A: Brief concept- Open compass traverse- A compass traverse is a technique for adding detail to a…

Q: What are point positioning equations?

A: Point positioning are used for positioning with GPS. In point positioning, a GPS receiver which…

Q: what station is the cross-drainage pipes be situated?

A:

Q: help

A:

Q: Draw half sectional Front View and Top View of the following component. 05 HOLE SIDI R25 P20 100…

A:

Q: is x correct?

A: Data Availabe: Asked: Centroid

Q: Define the Correlation between Angle of Frictionand Standard Penetration Number ?

A: The angle of friction is the angle formed by the normal reaction made with the normal force and the…

Q: Define oriented water.

A: Oriented water or water oriented:

Q: How much surveying must be supplied by the design firm?

A: Surveys can make a major impact depending on its quality.

Q: Differentiate between Profile leveling and cross sectioning (with the help of diagrams)

A: Profile Leveling: Profile levelling involves determining the elevations of the various points in…

Q: Arrange the following description in the form of profile level notes complete to elevation. A level…

A: Given:- A level is set up to take up the reading The reading of the benchmark = 3.120 m The…

Q: Determine the centroid coordinates, Xc and Yc, use table attached.

A: We have the properties of the given sections as,  W18X46 area, A = 13.5 in2 Depth of section, d =…

Q: res for a property survey.. Determine the adjusted length nd adjusted bearing of each course.…

A:

Q: Explain the method of grid leveling?

A: Leveling:- Leveling is a subset of surveying whose goal is to establish, verify, or measure the…