Design a basic wide-band, RC band stop filter with a lower cut-off frequency of 200HZ and a higher cut-off frequency of 900HZ. Vac Band Stap Flepone -3d8 Pass Band Paes Band Freguency fie) Low Pa Response Hgh Pa Response Frequancy e) Figure 1: Band Stop Filter Characteristics Assuming a capacitor, C value for both filter sections (CLP. CHP) of 0.2uF, calculate the values of the two resistors, RLP and RHP using the formula: 1. From the Low pass filter formula, Find RLP: 1. f. 2. From the High pass filter formula, Find RHP: 1 fr 2nRypCHP 3. Calculate the center frequency (f) and Bandwidth (BW): a. fc = Vfi x fr %3D b. BW = fr - f

Design a basic wide-band, RC band stop filter with a lower cut-off frequency of 200HZ and a higher cut-off frequency of 900HZ. Vac Band Stap Flepone -3d8 Pass Band Paes Band Freguency fie) Low Pa Response Hgh Pa Response Frequancy e) Figure 1: Band Stop Filter Characteristics Assuming a capacitor, C value for both filter sections (CLP. CHP) of 0.2uF, calculate the values of the two resistors, RLP and RHP using the formula: 1. From the Low pass filter formula, Find RLP: 1. f. 2. From the High pass filter formula, Find RHP: 1 fr 2nRypCHP 3. Calculate the center frequency (f) and Bandwidth (BW): a. fc = Vfi x fr %3D b. BW = fr - f

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Design a fourth-order Butterworth low-pass filter with a cutoff frequency of500 Hz and a passband gain of 10. Use as many 1kΩ resistors as possible.Compare the Bode magnitude plot for this Butterworth filter with that of theidentical cascade filter.
Design a high pass filter with a cut of frequency of K1 and a passband gain of K2. Take K1 equal to 27 in kHz and K2 is the 7 (b) Plot the Bode plot of the frequency response of the designed circuit using a python script and validate your answer. (c) How would you increase the passband gain by a factor of five without changing the cutoff frequency?
(a) as shown for a maximally flat second-order low-pass filter with fo =25 kHz, using the circuit as shown. Assume C =0.005μF.What is the filter bandwidth? (b) Use frequency scaling to change fo to 50 kHz.
The input power of a filter is 200 mW and its output power in dBm scale is 20 dBm. Accordingly, a) Does this filter provide Attenuation or Gain in a circuit? Why is that? b) What is the value of the power loss or gain in this filter?
For the filter circuits given below; a-) Determine the filter types and find the cut-off frequencies. b-) Input amplitude peak to peak for both circuits is 200mV; Plot the output signals as an amplitude time graph by applying a sinoicidal input signal with a frequency of 1kHz to scale with respect to the input signal.
There is a system that works with a sampling rate of 48 kpsp and requires a bandpass filter that lets the spectral components pass between the fa=12kHz and fb=16kHz sequences. If you are using a 32-tap FIR filter. What is the value of the central frequency, f0, in Hz of the band that passes the filter? And what is the outline of the frequency response for the filter passes bands?
A passive first order low pass filter is designed in way such that its cut-off frequency is 1 kHz. If the value of the resistance present in the filter circuit is 400 ohm, then what will be the value of the capacitance present in the filter circuit?
Derive an expression for the cut off frequency of a low pass RC filter
Practically, the de-emphasis filter in an FM receiver unit is often a simple resistance-capacitance (RC) circuit with transfer function. Hde(f)=1/(1+j2πfRC) i) Determine the 3-dB bandwidth and equivalent bandwidth. ii) Presume the modulating signal has bandwidth W, the carrier amplitude is A, and the single-sided power spectral density of the white Gaussian noise is N0. Solve for the noise power at the output of the de-emphasis filter circuit. iii) Find the noise power without the de-emphasis filter. iiii) Supposing RC = 6 × 10−5, and W = 15 kHz. Calculate the improvement in the output signal-to-noise ratio (SNR) provided by the de-emphasis filter. Express it in decibel (dB).
Draw frequency response curve of a bandpass filter whose end frequencies are 0.1 MHz and 0.4 MHz respectively. Consider peak amplitude as 1. Use your own scale and necessary values.
Supply voltage:V1=10Vppsin(2πf) Desingning RC and RL Low conquer Passive filter circuits? Cutoff frequencies in these filter circuits fc=37200Hz BW=? R=? C=?
Describe the possibility of building a second order filter with only resistors and capacitors? and design the cutoff frequency of second order filter for low pass filter. (Expected: Describe the possibility, design the second order filter for low pass filter circuit and design the cutoff frequency as equation only).