Design a common-emitter amplifier with an NPN transistor with B = 100 and whose voltage gain is - 20, Zin> 5K, Zout> 5K. The amplifier is biased in a voltage divider configuration with a bias source of + 20V and the peak AC input voltage is 300mV. The amplifier load is 1K. 1. Design of the polarization circuit.

Design a common-emitter amplifier with an NPN transistor with B = 100 and whose voltage gain is - 20, Zin> 5K, Zout> 5K. The amplifier is biased in a voltage divider configuration with a bias source of + 20V and the peak AC input voltage is 300mV. The amplifier load is 1K. 1. Design of the polarization circuit.

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter25: Television, Telephone, And Low-voltage Signal Systems

Section25.1: Television Circuit

Problem 5R: From a cost standpoint, which system is more economical to install: a master amplifier distribution...

See similar textbooks

Similar questions

In the common-emitter amplifier circuit shown in the figure, Vcc=9V, R1=27kΩ, R2=15kΩ, RE=1.2kΩ and RC=2.2kΩ. The transistor has β=100.a-) If Rsig=10kΩ and RL=2kΩ, calculate the IE value of the amplifier.b-) For small signal analysis of the transistor, find the value of Rin by deriving the π-modelc-) Calculate vo/vsig and io/ii.
The multistage amplifier circuit of Figure Q.2(b) have the following parameters:Q1 and Q2 : β = 200, VBE = 0.7 V, VT = 26 mV , VA = ∞Given that ICQ1 = 2 mA and VCEQ1 = 2 V. (i) Determine the value for RB4. List the assumption/approximation made in the analysis.(ii) Sketch and label the small-signal hybrid-π equivalent circuit at midbandfrequency range.(iii) Calculate the small signal hybrid-π model parameters: gm and rπ for Q1 and Q2. Then, determine Zi2 and Zo.
a) Differentiate between Common Emitter (CE), Common Collector (CC) and Common Base (CB) amplifiers. b) Do the DC Analysis of the circuit below and find out the DC collector voltage?c) Do the AC Analysis of the circuit below and find out the AC collector voltage?R1=30kΩΩ=610Ω
The common-emitter amplifier given in the figure in the circuit, Vcc=9V, R1=27kΩ, R2=15kΩ, RE=1.2kΩ and RC=2.2kΩ. Transistor β=100 has value. a-) If it has values of Rsig=10kΩ and RL=2kΩ Calculate the IE of the amplifier. b-) For small signal analysis of transistor Find the value of Rin by deriving the π-model c-) Calculate vo/vsig and io/ii.
4) By drawing the small signal model of the circuit given below, we can determine the total voltage and current gain values of the circuit, without the bypass capacitor on and without the bypass capacitor. Calculate separately for the two cases as it will be in the circuit (connected to the emitter end of the transistor). (β = 100, rS = 600 Ω, R1 = 27 KΩ, R2 = 4.7 KΩ, RC = 3.3 KΩ, RE = 680 Ω, RL= 15 KΩ, VCC = 10 V)
The dc bias circuit for a common emitter amplifier is shown in the figure. In the circuit, Vcc=15v,RB1=20k Ω,RB2=100k Ω,Rc=5.1k Ω,and RE1=1k Ω, Assume that when the transistor is on, the voltage drop from base to emitter VBE=0.7v. Also assume that β= ∞, which implies that the base current can be considered zero (IB=0) in your calculations. Solve for the base voltage VB. Solve for the emitter voltage VE. Solve for the emitter current IB. Solve for the collector current IC
In the common emitter amplifier, R1 = 50Ω, R2 = 1kΩ, and CL=1 pF. Determine the quiescent collector current, ICQ, needed such that the unity gain frequency, fu, = 1 GHz. Show your complete solution and state all your assumptions.
(a) Suppose υbe(t) = 0.005 sin 2000πt V in the bipolar amplifier as shown . Write expressions for υbe(t), vce(t), and υCE(t). (b) What is the maximum value of IC that corresponds to the active region of operation?
Draw the equivalent circuit for a common-emitter bipolar transistor amplifier andderive suitable formulae for the amplifier current gain, voltage gain and power gain.Neglect bias,decoupling and coupling components
A.What is the phase relationship between the AC input and output voltages in a common emitter amplifier ? What is the reason for the phase reversal ? B.What is the phase relationship between the ac input and output signal voltages in conmmon bas amplifier?what is the reason?
1. Find the overall noise figure of the following amplifier device?
What is the minimum base current required in A bipolar power transistor has a forward current gain of 20 and an inverse current gain of 0.1.How much base current is required to achieve a saturation voltage of 0.1 V at a collector current of 10 A? if βR of the transistor changes to 0.2?