Design a CT-FWR to supply a load of (50) with a waveform of the following specifications: -  Vdc = 12 V  Ripple factor = 0.1 %  the main power supply is (220 Vrms, 50 Hz). Determine the following values: - 1- The value of capacitor filter. 2- The maximum load voltage (VmR) 3- The transformer turns ratio (a)

Design a CT-FWR to supply a load of (50) with a waveform of the following specifications: -  Vdc = 12 V  Ripple factor = 0.1 %  the main power supply is (220 Vrms, 50 Hz). Determine the following values: - 1- The value of capacitor filter. 2- The maximum load voltage (VmR) 3- The transformer turns ratio (a)

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.14P: A single-phase 50-kVA,2400/240-volt,60-Hz distribution transformer is used as a step-down...

See similar textbooks

Similar questions

If we have a transformer (500: 50) connected to a 220V voltage source with a frequency of 60Hz, if it is connected to a bridge uniform circuit, a full wave of the bridge type, as well as with the throttle input filter, calculate the continuous voltages after filtering, the effective remaining voltages, the ripple factor, the critical inductance, and the minimum filtering capacitance if the value of inductance is equal to L = 30H, amplitude of 500uF, and load impedance RL = 700
An ideal battery of terminal voltage Vs= 120V supplies a resistive load of resistance 10 Ω as shown in the bellow class-A chopper circuit. The chopping frequency is f =1000 Hz and the duty cycle is set to be 0.25. (a) Sketch approximately to scale the output voltage waveform. (b) Determine the average output voltage. (c) Determine the rms output voltage. (d) Determine the dc power and ac power. (e) Determine the ripple factor and the chopper efficiency
For type A chopper, dc source voltage = 250 V, load resistance = 10 Ω. Take a voltage excess of 2V across chopper when it is on. For a duty cycle of (0.004*Vs ), calculate (a) average and rms values of output voltage and (b) chopper efficiency.
-) The active and reactive power drawn by the mixer fed from a 230 Vrms, 50 Hz single phase AC network was measured as 600 W and 100 VAR, respectively. According to this information: a) Calculate the apparent power drawn from the network? b) Calculate the current drawn from the network? c) Calculate the cos(a).
Is it possible to measure the phase-shift angle in an AC single-phase circuit by an indirect method using an ammeter and a voltmeter? - Yes, but an instrument must be added to measure the active resistance of the load. - Yes, but an instrument must be added to measure the active power dissipated by the load. - Yes, but an instrument must be added to measure the frequency.
2) A single -phase power transformer of 150 MVA, 15/200 kV has a Resistance in unit of 1.1% and reactance per unit of 4.5%. The Magnetization impedance is J95 per unit. a) Find the equivalent circuit of the transformer referred to the bass side voltage. b) Calculate the transformer voltage regulation under conditions Nominal and F.P. 0.9 in delay.
Define the harmonic frequency and interharmonic frequency used in power system quality.
A non-sinusoidal quasi-square wave voltage v(t) is applied to a nonlinear load, resulting in a non-sinusoidal current i(t). The voltage and current waveforms are shown below. Assume any values of your choice for Vp (≤ 200 V) and Ip (≥ 5 A). 1. calculate the average power and net power factor of the load. 2. The total load harmonic distrotion (THD) of the load current, assuming the smallest frquency term as fundamental.
A transformer has a ratio of 4:1. The high voltage side is connected to a 240 Vrms source. The low voltage side (secondary) is connected to an impedance ZL = 20 + j10 Ω.a. What is the value of the load impedance when referred to the primary?b. (in A rms) What is the current out of the source?
A Step-Down Transformer. A transformer connected to a 120 V (rms) ac line is to supply 12.0 V (rms) to a portable electronic device. The load resistance in the secondary is 5.00 Ω. (a) What should the ratio of primary to secondary turns of the transformer be? (b) What rms current must the secondary supply? (c) What average power is delivered to the load? (d) What resistance connected directly across the 120 V line would draw the same power as the transformer? Show that this is equal to 5.00 Ω times the square of the ratio of primary to secondary turns.
A transformer has a ratio of 4:1. The high voltage side is connected to a 240 Vrms source. The low voltage side (secondary) is connected to an impedance ZL = 20 + j10 Ω.a. (in Vrms) What is the value of the source voltage when referred to the secondary? b. (in A rms) What is the current at the secondary?c. (in V rms) What is the voltage at the secondary?
In the circuit given on the side Ra=Rb=Rc=Basic frequency of 13 Ohm loadsit is powered by an AC voltage of f= 60 Hz. Power derived from the sourceits value was measured as Pk=9372.12 Watts. Each switchingthe element is triggered in such a way that it will be at 180 degrees.The DC bus voltage (E=?) and the effective value of the ic phase current(ic rms=?) calculate.