Design a DC motor circuit to drive A fan-type load with a torque equation equal to: TL=1.34×10−7ω2TL=1.34×10−7ω2 N.m The fan speed range is from 500 to 1200 rpm. To achieve the required operation, the armature voltage of the motor is adjusted by a single-phase, full-wave, ac/dc converter. The input voltage and frequency to the converter are 480 V (rms) and 50 Hz. choose the motor type, show the motor rating, αα range, Supply voltage, and frequency, and any required other information Modify the design to automatically adjust the voltage drive the load within the specified speed range. show the control variable, controller type, connection, and controller weights. design the single-phase, full-wave, ac/ dc converter. show design specifications, the reason for DC motor selection. correct manual circuit, and correct automatic closed-loop control circuit

Design a DC motor circuit to drive A fan-type load with a torque equation equal to: TL=1.34×10−7ω2TL=1.34×10−7ω2 N.m The fan speed range is from 500 to 1200 rpm. To achieve the required operation, the armature voltage of the motor is adjusted by a single-phase, full-wave, ac/dc converter. The input voltage and frequency to the converter are 480 V (rms) and 50 Hz. choose the motor type, show the motor rating, αα range, Supply voltage, and frequency, and any required other information Modify the design to automatically adjust the voltage drive the load within the specified speed range. show the control variable, controller type, connection, and controller weights. design the single-phase, full-wave, ac/ dc converter. show design specifications, the reason for DC motor selection. correct manual circuit, and correct automatic closed-loop control circuit

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter32: Three-phase Motors

Section: Chapter Questions

Problem 6RQ: Name three factors that determine the torque produced by an induction motor.

See similar textbooks

Similar questions

Design a DC motor circuit to drive A fan-type load with a torque equation equal to: TL=1.34×10−7ω2TL=1.34×10−7ω2 N.m The fan speed range is from 500 to 1200 rpm. To achieve the required operation, the armature voltage of the motor is adjusted by a single-phase, full-wave, ac/dc converter. The input voltage and frequency to the converter are 480 V (rms) and 50 Hz. choose the motor type, show the motor rating, αα range, Supply voltage, and frequency, and any required other information Modify the design to automatically adjust the voltage drive the load within the specified speed range. show the control variable, controller type, connection, and controller weights.
A four-pole induction motor drives a load at 2500 rpm. This is to be accomplished by using an electronic converter to convert a 400-V dc source into a set of three-phase ac voltages. Find the frequency required for the ac voltages assuming that the slip is 4 percent. The load requires 2 hp. If the dc-to-ac converter has a power efficiency of 88 percent and the motor has a power efficiency of 80 percent, estimate the current taken from the dc source.
A 4-pole induction motor drives a load at 2500 rpm. This is to be accomplished by using an electronic converter to convert 400 Volts DC into a set of 3-phase AC voltages. Find the frequency required for the AC voltages assuming that the slip is 4 percent. The load requires 2 hp. If the DC-to-AC converter has a power efficiency of 88 percent and the motor has a power efficiency of 80 percent, estimate the current taken from the DC source.
Q5:- Adjust a fire angle for a three-phase fullwave semi-controlled converter to feed the separately exciter DC motor to get a load torque that can be reached to 730 rpm. When the supply voltage of converter is 160 volts per-phase and the absorbed current through the armature 40A with resistance 0.2 and a constant back emf 0.4v/rpm. Then find the maximum speed for motor assume the previous parameters values are a constant.
A 80 kW, 440V, 800 rpm DC. Motor is operating at 600 rpm and developing 75 % rated torque when controlled by a 3-phase, six-pulse thyristor converter. If the back emf at rated speed is 410 V, determine the triggering angle of the converter. The input to the converter is 3-phase, 415 V, 50 Hz AC supply.
A brushed DC motor is spinning at a maximum no-load speed of 6206 rpm. The nominal brush voltage drop is 0.67 V and the rated terminal voltage of the machine is 13 V. Determine the voltage constant, Ke, of the machine in Vs/rad.
A 6060-HzHz induction motor is needed to drive a load at approximately 840rpm. a) Determine the maximum number of poles required to drive the load at 840 rpm. b) Determine the maximum number of poles required to drive the load at 840 rpm.
A 100V shunt motor is developing 6Hp while operating at an overall efficiency of 86%. The armature and shunt field resistances are 0.06Ω and 50Ω respectively. Determine the SPL.
A 0,9 kW DC shunt motor is loaded by a constant torque of 12 Nm. The armature resistance of the motor is 5 Ω, and the field constant KØ = 3 Vs/rad. The motor is driven by a half wave thyristor converter. The power source is a 140 V, 50 Hz. The triggering angle of the converter is 450 and the conduction period is 1650 . Calculate the motor speed and the developed power.
The armature resistance of a compound direct current motor with a long shunt is given as 0.25 Ω, the series winding resistance is 0.35 Ω and the shunt windingresistance is 600 Ω. Ifthe armature of the direct current motor rotates at 1200 rpm, and it draws 25 amps from the armature windings to create a torque of 140 Nm, find the efficiency of the motor.
A DC chopper is used in regenerative breaking mode of a dc series motor. The dc supply is 600 V, the duty cycle is 70%. The average value of armature current is 100 A. It is continous and ripple free. What is the value of power feedback to the supply ?
A 50-KW, 220V, 50 Hz, squirrel-cage three-phase induction motor is needed to rotate a mine conveyor belt drive. The motor starts sometimes under load, but most of the time is needed to run at rated speed and slip of 3.5%. Propose an appropriate design of this drive motor in order to suit the application. Motivate and then illustrate your design with suitable drawings and speed (slip)-torque graphs.