Design a double angle tension member that is fillet welded to a gusset plate. Assume that the angles will be made from A36 steel, and the gusset plate from A572 Gr. 50 steel. Use 70ksi electrode. Design the system to resist a factored load of 200 kips. Check all applicable limit states that are possible. Provide your results on a sketch with standard weld symbols and details.

Design a double angle tension member that is fillet welded to a gusset plate. Assume that the angles will be made from A36 steel, and the gusset plate from A572 Gr. 50 steel. Use 70ksi electrode. Design the system to resist a factored load of 200 kips. Check all applicable limit states that are possible. Provide your results on a sketch with standard weld symbols and details.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter8: Eccentric Connections

Section: Chapter Questions

Problem 8.4.15P

See similar textbooks

Similar questions

Select an American Standard Channel shape for the following tensile loads: dead load = 54 kips, live load = 80 kips, and wind load = 75 kips. The connection will be with longitudinal welds. Use an estimated shear lag factor of U = 0.85. (In a practical design, once the member was selected and the connection designed, the value of U would be computed and the member design could be revised if necessary.) The length is 17.5 ft. Use Fy=50 ksi and Fu=65 ksi. a. Use LRFD. b. Use ASD.
a. Use LRFD and design a welded connection for the bracket shown in Figure P8.4-19. All structural steel is A36. The horizontal 10-inch dimension is a maximum. b. State why you think your weld size and configuration are best.
Use an elastic analysis and compute the extra load in the weld (in kips per inch of length) caused by the eccentricity.
Use an elastic analysis and compute the extra load in the weld (in kips per inch of length) caused by the eccentricity.
Find the Load Capacity of the weld if the throat thickness is 8. 13 mm, Nominal Tensile Strength, Fu = 520 MPa, and length of weld = 400 mm.
5. Determine the size of the fillet weld required for the shear and tension connection if p = 200KN, 5 = 150mm, b = 150mm and d = 20mm. Use E70 electrodes and assume the column and bracket plate does not control the strength. Steel Column Bracket (out from resection UNMA COC
If the structural frame is replaced to structural steel and the connections is to be designed, determine the following Determine the centroid of the weld measured from the given origin A. Determine the direct shear load in the welds. Determine the required size of the fillet weld(E60xx) if the maximum resultant load is 750,000 N/mm
a. Determine the design strength of a 1-in length of a 1/4-in fillet weld formed by the shielded metal arc process (SMAW) and E70 electrodes with a minimum tensile strength FEXX = 70 ksi. Assume that load is to be applied parallel to the weld length.b. Repeat part (a) if the weld is 20 in long.c. Repeat part (a) if the weld is 30 in long.
Determine the maximum factored load P, that can be carried by the connection shown in the Figure P7. 1. The weld is 6 mm fillet weld. All structural steel is A36. E70 electrode is used
For the gable frame shown in fig . below , roof dead load = 60 KN / m . Determine total static load applied on the member CB . And find a suitable E ? XX is the most popular electrode used for fillet welds made by the SMAW method if length at both point B .and C is equal 30 cm
Design a welded connection (E70) for an MC 9x23.9 of A992 Grade 50 steel connected to a 3/8-inch-thick gusset plate. The gusset plate is A36 steel. Minimize the length of the longitudinal welds by using the maximum fillet weld size permitted (AISC J-2b). Show your results on a sketch, complete with dimensions. Use LRFD. Hint: Design it with both longitudinal welds and a transverse weld. For simplicity in the iteration of this problem take U = 1.0 and thus no shear lag effects. Also, do not forget to consider the block shear that will occur in the gusset plate.
Determine the maximum service load, P, that can be applied if the live load to dead load ratio is 2.5. Each component if PL 5/8x7 of A242 steel (Fy = 50 ksi and Fu = 70 ksi). The weld is a 5/16-inch fillet weld, E70 electrode. Use LRFD. Note: Block shear cannot occur for this connection.