Design a pipe to supply water from the elevated tank to the demand point at a discharge rate of 0.05 m³/s. Use Galvanized Iron pipe and assume water temperature as 15°C Minor losses can be neglected due to smooth transitions, Tables and charts are available here: Exam References.pdf Tank 3 m-X -70 m- -352 m- 2 m Demam Point

Design a pipe to supply water from the elevated tank to the demand point at a discharge rate of 0.05 m³/s. Use Galvanized Iron pipe and assume water temperature as 15°C Minor losses can be neglected due to smooth transitions, Tables and charts are available here: Exam References.pdf Tank 3 m-X -70 m- -352 m- 2 m Demam Point

Residential Construction Academy: House Wiring (MindTap Course List)

4th Edition

ISBN:9781285852225

Author:Gregory W Fletcher

Publisher:Gregory W Fletcher

Chapter10: Electrical Box Installation

Section: Chapter Questions

Problem 8RQ

See similar textbooks

Similar questions

Include a free body diagram The water level in a tank is 34 ft above the ground. A hose is connected to the bottom of the tank at the ground level and the nozzle at the end of the hose is pointed straight up. The tank cover is airtight, but the pressure over the water surface is unkown. Determine the minimum tank air pressure (gage) that will cause a water stream from the nozzle to rise 72 ft from the ground.A. 13.5 psiB. 15.5 psiC. 16.5 psiD. 14.4 psi
Solve the F2-7 Question
Design a bar screen for the following conditions:Peak design flow = 54451 m3/d Velocity through the rack at peak flow = 0.9 m/s Angle with the horizontal = 60o
The water level in a tank is 34 ft above the ground. A hose is connected to the bottom of the tank at the ground level and the nozzle at the end of the hose is pointed straight up. The tank cover is airtight, but the pressure over the water surface is unkown. Determine the minimum tank air pressure (gage) that will cause a water stream from the nozzle to rise 72 ft from the ground. Include your fbd. Choices: A.13.5 psi B.16.5 psi C.15.5 psi D.14.4 psi
A water main is an 18-in diameter concrete pressure pipe. Calculate the energy loss over 1-mile length if it carries 7.50ft^3/s of water. Answer is HL=28.5ft Please show how to get there.
A fan is used to force air having a temperature of 20°C theough the 200 mm diameter galvanized sheet metal duct. Determine the head added if the length of the duct is 150 m and the flow is to be 0.15m^3/s. Take f=0.023 and kinematic viscosity of air = 15.1x10-6 m2/s.
The water level in a tank is 34 ft above the ground. A hose is connected to the bottom of the tank at the ground level and the nozzle at the end of the hose is pointed straight up. The tank cover is airtight, but the pressure over the water surface is unkown. Determine the minimum tank air pressure (gage) that will cause a water stream from the nozzle to rise 72 ft from the ground. Show FBD and hoode the correct answer below A. 16.5 psi B. 13.5 psi C. 15.5 psi D. 14.4 psi
Input-F=209
1. What is the velocity at the 50 mm pipe in m/s? 2. What is the velocity at 30 mm pipe in m/s? Thankyou ill upvote
Estimate the total installed cost (in 1998 dollars) of the baghouse of Problem 6,11, assuming it is mild steel, is uninsulated, and uses 6-inch Nome^ bags on cages that snap in from the top, with built-in venturis.
A venturi meter of 150 × 75 mm size is fixed in a horizontal pipe carrying water. The pressure gauge at entry read 137.34 kN/m^2 (gauge). The pressure at the throat was 37.5 cm of mercury (vacuum). -Calculate the coefficient of discharge for the venturi meter if the flow rate is 102 m^3/hr. choices: a.) 0.088 m^3/s b.) 0.345 m^3/s c.) 0.197 m^3/s d.) 0.441 m^3/s STRICTLY SHOW COMPLETE FBD need asap
The water closet having an integral part of trap S and P-type outlet have a water seal size of ____________. a.) 25 mm b.) 50 mm c.) 75 mm d.) 100 mm