Design a regulator circuit as given below for V; = 16V and V, = 12V. The powers dissapatedby the BJT transistor and the Zener diode required as Par = 16mW and Pz = 12.7mW,respectively. Assume the transistor parameters as ß = 50, VBE = 0.7V. Find Vz, Iz, VCe, Ic, IL.R1, Ig, Ig, R.(regulated)(unregulated)RL.

Answered: Image /qna-images/answer/6f1878d6-f2c9-45bb-9e5c-71e6f48a87b7.jpg

Design a regulator circuit as given below for V = 16V and V, = 12V. The powers dissapated by the BJT transistor and the Zener diode required as PaT = 16mW and Pz = 12.7mW, respectively. Assume the transistor parameters as ß = 50, VBE = 0.7V. Find Vz, Iz, VCe, Ic. IL. R1, Ig, IR. R. %3D (unregulated) (regulated) RL

Design a regulator circuit as given below for V = 16V and V, = 12V. The powers dissapated by the BJT transistor and the Zener diode required as PaT = 16mW and Pz = 12.7mW, respectively. Assume the transistor parameters as ß = 50, VBE = 0.7V. Find Vz, Iz, VCe, Ic. IL. R1, Ig, IR. R. %3D (unregulated) (regulated) RL

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Consider a voltage-divider configuration of n-channel enhancement-type MOSFET where R1 = 12 MΩ, R2 = 7 MΩ, RD = 3 kΩ, RS = 1 kΩ. The MOSFET has a threshold voltage VGS(Th) = 3V, and one example point on the transfer characteristics curve is VGS(on) = 6V, ID(on) = 5 mA. Determine VGSQ, IDQ, Vs, VD, VDS assuming VDD = ( 80 ÷ 10 ) +20 V
In order to express the effect of the internal capacitors of BJT and the high frequency reception, the current gain expression depending on the frequency (Figure b) (hfe) is used in the case of collector emitter short circuit, voltage source connected at base end and emitter grounded (Figure la).. The catalog information of the 2N2222 transistor is given in Figure Ic. In the catalogue, when Ic=20 mA, it is seen as fT=250 MHz. a) Find the total capacitor effect for the case where gm> > wCμ. (Cpi) + (Cμ) = ?pF
If RB=12KΩ, RC=150Ω, VBB=7V, VCC=18V determine the IB, IC, IE and collector – emitter voltage in the circuit given below. The transistor has a gain (β) =150. Assume forward voltage drop of the BE junction is 0.7 V (Fig Q2 (d))
Using IC that is approximately equal to IE. Determine the value of emitter voltage VE, when VCC=19V, RC=1476 ohms, RE=207 ohms, VC=6 V and R2=4811ohm
For the transistor , IS = 4 × 10−16 μA,βF = 75, and βR = 4. (a) Label the collector, base,and emitter terminals of the transistor. (b) What isthe transistor type? (c) Label the emitter-base andcollector-base voltages, and label the normal direction for IE , IC, and IB. (d) Write the simplified formof the transport model equations that apply to thisparticular circuit configuration. Write an expressionfor IE /IB. Write an expression for IE /IC. (e) Findthe values of IE , IC, IB, VC B, and VE B.
The following are the required circuit parameters for the T1 transistor in the following circuit. VBE=0.7 V, β=100, Cbc=Cμ=100pF,Cπ=Cbe=200pF, VA=∞, VT=26mV, and ro negligence;a) Find IB, IC, IE currents.b) Find VCE, VB, VC and VE voltages.c) Set the Q working point by drawing the load line of the circuit.d) Find the lower sector frequency value.e) Find the upper cut frequency value.R: 409
4) By drawing the small signal model of the circuit given below, we can determine the total voltage and current gain values of the circuit, without the bypass capacitor on and without the bypass capacitor. Calculate separately for the two cases as it will be in the circuit (connected to the emitter end of the transistor). (β = 100, rS = 600 Ω, R1 = 27 KΩ, R2 = 4.7 KΩ, RC = 3.3 KΩ, RE = 680 Ω, RL= 15 KΩ, VCC = 10 V)
For the transistor , IS = 6×10−16 μA,αF = 0.985, and αR = 0.25. (a) What type oftransistor is in this circuit? (b) Label the collector, base, and emitter terminals of the transistor.(c) Label the emitter-base and collector-base voltages, and label the normal direction for IE , IC, andIB. (d) Write the simplified form of the transportmodel equations that apply to this particular circuitconfiguration. Write an expression for IE /IC. Writean expression for IE /IB. (e) Find the values of IE ,IC, IB, βF , βR, VE B, and VC B.
Given VTH=1.2 and k=0.5mA/V2, determine the following a) The value of ID, VGS and VDS b) Mode of operation of the MOSFET. (Verify this answer)
A. Design a fixed bias-transistor circuit using VBB = VCC = 10 V for a Q-point of IC = 5 mA and VCE_ 4 V. Assume βDC = 100.The design involves finding RB and RC. B. 4. Design an emitter bias network at Q-point ICQ = ½ ICsat and VCEQ = ½ VCC. Use VCC = 20 V, ICsat = 10 mA, β = 120, and RC = 4RE
For the transistors in this question, use |Vt| = 0.1V, |VA| = 10V, kn,p = 12.5mA/V2. The signal source has 0.1 mV amplitude and 1 kHz frequency. Calculate Rout, Gm and Av for the circuits separately ?
Q 3 emitter voltage divider-biased circuit. Given that RB = 25kΩ, R2 = 2.5kΩ, RC = 5kΩ, RE = 1kΩ, VCC = 22V, VBE = 0.7V, C1 = C2 = 10µF and β= 90, (i) the Thevenin equivalent circuit. (ii) the base current, IBQ, the collector current, ICQ and the collector-emitter voltage, VCEQ. (iii) the collector voltage, VC, the emitter voltage, VE, and the base voltage, VB. (b) If the circuit in Figure Q3 has ro = 40kΩ, (i) Draw the AC equivalent circuit using re model. Label all currents, voltages, resistors and directions correctly. (ii) Analyze the circuit to determine re, input impedance, Zi, output impedance, Zo and voltage gain, Av.