Design a square key for a 3 in diameter shaft to withstand a torque of 30000lb-in. The design stresses in shear and bearing can be safely taken as 11 ksi and 22 ksi, respectively. Find the length (inches) From Table AT 19, b=t=3/4 in

Design a square key for a 3 in diameter shaft to withstand a torque of 30000lb-in. The design stresses in shear and bearing can be safely taken as 11 ksi and 22 ksi, respectively. Find the length (inches) From Table AT 19, b=t=3/4 in

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.3P: A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at...

See similar textbooks

Related questions

Q: Ammonia contained in a piston-cylinder assembly, initially saturated vapor at 0˚F, undergoes an…

Q: Ammonia contained in a piston–cylinder assembly, initially saturated vapor at T1 = 6°F, undergoes an…

A: Introduction: The isothermal process is classified into two categories. one isothermal expansion…

Q: 2.4-4 A horizontal rigid bar ABC is pinned at end A and supported by two cables at points B and C. A…

A: given; P=10KN AD=1.5mAB=1.5mBC=1.5mAC=3mminimum cross sectional area of cable(A)=?yield…

Q: 0.4 m D d = 0.15 m Part A If the 5.2-kg block is suspended from the pulley B and the sag of the cord…

Q: A refrigerant 22 vapor compression system includes a heat exchanger in the system. The heat…

Q: An uninsulated 100-mm diameter steam pipe runs for 25-meters inside a room whose walls and air are…

Q: For the following figure in writing the dimensions if we write the symbol R Instead of the value of…

A: Here I am going to explain, what will happen if we write the symbol R instead of the value of the…

Q: 1. An engineering manufacturing company has established that the relationship between the quantity…

A: Given: Quantity solved per month or demand per month=D And sales price for each product=p And demand…

Q: #3/ 1516 13 16 1016 15. 48 63 126 2516 74 31b Find R+O

Q: During heating and humidification process briefly describes how the psychrometric properties below…

A: As per our guidelines we are supposed to solve only 3 subparts if multiple subparts are asked.…

Q: The space between two 6-in. long concentric cylinders is filled with glycerin (viscosity = 8.5 X 10³…

Q: Both portions of the rod ABC are made of an aluminum for which E= 70 GPa. Given: P = 5 kN. 0,4 m 0.5…

A: The given information in the problem is shown in the following attached image:

Q: Car A is traveling at a location where the speed limit is 100 km/h. The police officer in car P…

Q: 500 MMSCFD of supercritical steam generated in the steam generator (shown in the sketch below) at…

A: Note: As per Guidelines only 3 part will be answered, please post again this question and asked for…

Q: A beam is supported and loaded as shown in (Figure 1). Use the following data: 1 = 0.90 m, a = 0.25…

Q: In an archery test, the acceleration of the arrow decreases linearly with distances from its initial…

Q: 2.48 Knowing that a = 20°, determine the tension (a) in cable AC, (b) in rope BC. Answer Fig. P2.48…

Q: he third force so that the resultant of the three forces is vertically downward with a magnitude of…

Q: The flanged steel cantilever beam with riveted bracket is subjected to the couple and two forces…

Q: The deceleration of the mass center G of a car during a crash test is measured by an accelerometer…

A: Given DataX=0.8m

Q: How high a relative humidity must be for a 35°C air in order to obtain a saturated air at 18°C by…

A: Given:Initial Air temperature, T1=35oCFinal air condition, T2=18oC, saturated airFind:Relative…

Q: Shown in figure below, the manometer fluid of density 875 kg/m3 shows a column height difference of…

A: Given data the density of the manometric fluid (ρm) = 875 kg/m3 ∆h = 3 cm Po = 101 kPa To…

Q: Question 27 Three particles of mass m, 4m and 4m are constrained to move along a frictionless…

Q: A 5m copper tube is heated externally to 100degC. Air is heated by passing it through the 40mm…

A: Given Temperature, T1 = 100oC Inlet temperature, Ti = 20 oC Exit temperature, Te = 88 oC Diameter, d…

Q: Draw the Material Science tetrahedron and discuss briefly the interrelation of each component.

Q: At the beginning of compression in an ideal dual combustion cycle, the working fluid is 1 lb of air…

Q: 5. A student living in a 4 m x 6 m x 6 m dormitory room turns on her 150 watts fan before she leaves…

Q: A 13m bar of negligible weight rests on the smooth planes as shown in the figure. Determine the…

A: Apply force equilibrium in horizontal direction. RAsin30°-RBsin45°=0RA=1.4142RB ...... (1)…

Q: 2. A 12 cm diameter long bar initially at a uniform temperature of 40C is placed in a medium at 650C…

Q: Example-1:- V A rigid tank with a volume of 1.8 m3 contains 15 kg of saturated liquid- -: vapor…

Q: Create a solving problem about Longitudinal Vibration. Show problem and solution.

Q: 138) Given: Find: p= 150 psi max. Longitudinal Jom T Finex = 33 x/f+ Hoop fr Girth joint Fmax Long…

A: Given data:- Internal pressure p=150 psi And suppose the thickness is unit ft that means t= 1 ft And…

Q: d. Determine the velocity in the discharge side. e. Determine the velocity on the suction side. f.…

A: Since you have posted a question with multiple sub-parts, we will solve the first three subparts for…

Q: Starting from rest at home plate, a baseball player runs to first base (90 ft away). He uniformly…

Q: A 40- kg block is placed on the uniform 10-kg beam, that is supported by the cable, which is…

Q: how does mechanical efficiency affect net power output calculation of a gas turbine power plant.…

A: Any internal combustion engine that uses gas as the working fluid to turn a turbine is referred to…

Q: 2. (a) Find the resultant of these three forces in vector form. (b) Find the magnitude of part (a)…

Q: mes checks the pressure on his front left tire, and it reads 25 pound per square inch (psi). His…

A: pressure required=32psi current pressure=25psi

Q: 04-Neglecting friction forces, and the radius of the pulley. Determine the following: 1- The tension…

Q: The acceleration of a particle is given by a = 6t-21, where a is in meters per second squared and t…

Q: For the bell crank shown in equilibrium in figure below, determine the normal and shearing stress of…

A: The given information in the problem is represented in the following attached image:

Q: -AB, AC, and AD cables are used to support the 30-kg flowerpot as shown in Fig.2. Determine the…

Q: A placekicker is attempting to make a 41-yard field goal. If the launch angle of the football is…

A: The vertical and horizontal speed of the ball can be expressed as shown below. The horizontal…

Q: Passengers in the jet transport A flying east at a speed of 800 km/h observe a second jet plane B…

A: Given, Velocity of A, VA =800 km/hr To determine, the velocity of B

Q: The flanged steel cantilever beam with riveted bracket is subjected to the couple and two forces…

A: Given:Forces acting on the cantilever:F1=2.10 kNF2=1.15 kN

Q: Air (assuming constant specific heats of Cp = 1.008 J/kgk. Cy=721 J/kgk, k = 1.4) is compressed…

Q: 2. One cubic foot of oxygen at 100°F and 15 psia is compressed adiabatically to 0.4 ft. What then,…

A: Given data: P1=15 psiT1=100°F=310.93 KV1=1 ft3V2=0.4 ft3 Need to determine the final temperature and…

Q: Two rods and one cable are attached to the supports at O. If two of the forces are as shown,…

A: Given:Three forces acted as given:F1=400 lbF2=FF3=840 lbResultant of the three forces=1060 lb in…

Q: A student living in a 4-m x 6-m x 6-m dormitory room turns his 150-W fan on before she leaves her…

Q: 1. The specific weight of water at ordinary pressure and temperature is 62.4 lb/ft (9.81 kN/m³). The…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

100%

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft has a full quarter-circular fillet, and the smaller diameter D1= 100 mm. If the allowable shear stress at the stress concentration is 100 MPa, at what diameter will this stress be reached? Is this diameter an upper or a lower limit on the value of D2?
A full quarter-circular fillet is used at the shoulder of a stepped shaft having diameter D2= 1.0 in. (see figure), A torque T = 500 lb-in. acts on the shaft. Determine the shear stress at the stress concentration for values as follows: D1= 0.7,0.8, and 0.9 in. Plot a graph showing versus D?
Repeat Problem 10.3-15 using L = 3.5 m, max = 3 mm, and EI = 800 kN·m2.
A stepped bar with a hole (see figure) has widths h = 2.4 in. and c = 1.6 in. The fillets have radii equal to 0.2 in. What is the diameter d max of the largest hole that can be drilled through the bar without reducing the load-carrying capacity?
The propeller shaft of a large ship has an outside diameter 18 in. and inside diameter 12 in,, as shown in the figure. The shaft is rated for a maximum shear stress of 4500 psi. If the shaft is turning at 100 rpm, what is the maximum horsepower that can be transmitted without exceeding the allowable stress? If the rotational speed of the shaft is doubled but the power requirements remain unchanged, what happens to the shear stress in the shaft?
A propeller shaft of solid circular cross section and diameter d is spliced by a collar of the same material (see figure). The collar is securely bonded to both parts of the shaft. What should be the minimum outer diameter dyof the collar in order that the splice can transmit the same power as the solid shaft?
A solid circulai' aluminum bar AB is fixed at both ends and loaded by a uniformly distributed torque 150N·n/m. The bar has diameter d = 30 mm. Calculate the reactive torques at the supports and the angle of twist at midspan. Assume that G = 28 GPa.
A stepped shaft ACB having solid circular cross sections with two different diameters is held against rotation at the ends (sec figure). If the allowable shear stress in the shaft is 6000 psi, what is the maximum torque (T0) that may be applied at section C? Find (T0)max if the maximum angle of twist is limited to 0.55º. Let G = 10,600 ksi.
A steel punch consists of two shafts: upper shaft and lower shaft. Assume that the upper shaft has a diameter d1= 24 mm and the bottom shaft has a diameter d2= 16 mm. The punch is used to insert a hole in a 4 mm plate, as shown in the figure. If a force P - 70 kN is required to create the hole, what is the average shear stress in the plate and the average compressive stress in the upper and lower shaft of the punch?
A torque T is applied to a thin-walled tube having a cross section in the shape of a regular hexagon with constant wall thickness t and side length b (see figure). Obtain formulas for the shear stress rand the rate of twist